feed Subscribe to feed
pic
23. 07
2018

Manual Helical Milling

Written by: admin - Posted in: Uncategorized - Tags: , ,

23. 07
2018

Bridgeport Vertical Milling Machine Jhead Dro (30217)

Written by: admin - Posted in: Uncategorized - Tags: , , , ,
Bridgeport Vertical Milling Machine Jhead Dro (30217)


Bridgeport Vertical Milling Machine Jhead Dro (30217)


Bridgeport Vertical Milling Machine Jhead Dro (30217)


Bridgeport Vertical Milling Machine Jhead Dro (30217)


Bridgeport Vertical Milling Machine Jhead Dro (30217)


Bridgeport Vertical Milling Machine Jhead Dro (30217)


Bridgeport Vertical Milling Machine Jhead Dro (30217)


Bridgeport Vertical Milling Machine Jhead Dro (30217)


Bridgeport Vertical Milling Machine Jhead Dro (30217)


Our stock number: 30217. BRIDGEPORT VERTICAL MILLING MACHINE. Table Size: 9″ x 42″. Vertical Travel Of Knee: 16. Spindle Speeds: (8) 80 – 2720 RPM. Spindle, Power Feeds: (3). 1 HP Spindle Motor. Newall C-80 Two Axis Digital Readout. Approximate Weight: 2000 Lbs. Bank Wire Transfers and Checks. Skids shown in pictures are not included with the item. 02 to discuss any trade-ins or items you have available for sale. Located in Cincinnati, Ohio. Is a worldwide dealer in new and pre-owned conventional and CNC Metalworking Machinery. In addition to Machinery and Equipment Sales, C. Woods Machinery Moving Division has the capacity to move a single piece of equipment or entire facility! The item “BRIDGEPORT VERTICAL MILLING MACHINE JHEAD DRO (30217)” is in sale since Wednesday, July 11, 2018. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “buyusedcheaper” and is located in Cincinnati, Ohio. This item can be shipped to United States.

  • Model: SERIES I
  • MPN: SERIES I
  • Brand: Bridgeport
23. 07
2018

ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA

Written by: admin - Posted in: Uncategorized - Tags: , , , , , , , ,
ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA


ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA


ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA


ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA


ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA


ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA


ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA


ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA


ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA


ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA


ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA


ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA



For more information on our products. Please send message to us. Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. What Customers Have To About Us. ” Delivered as promised and item is as described “. Just what i was looking for. Had a problem-was able to successfully resolve it. AL-310S X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8in Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed adjust knob Speed can be adjust according to operator’s requirement, ranging from 0-9. Jog switch Normally, jog switch should be at FEED position. For jog movement, just switch to 0 position. Kept holding the switch until it travels to requires position. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). To stop jog operating, you must first turn “FEED KNOB” to “0″(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. X traverse (Left-Right Travel). 8 x 4.5 x 13 inches. Power Feed For Milling Machine. Brand new power feed. X traverse (left-right travel). Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. All items are dispatched from our warehouse in Azusa, CA. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Your product was damaged during transit. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. 25 years Industry Experience. The item “ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA” is in sale since Saturday, June 23, 2018. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “fans-autoparts” and is located in Hacienda Heights, California. This item can be shipped to United States.

  • Brand: FANS-AUTO
  • Model: AL-310S
  • MPN: ZY8LX00363
  • Voltage: 110V, 50/60Hz
  • Rotate speed: 0-200 RPM
  • Max torque: 450 in-lb
  • Max feed rate: 650mm/min
  • Max return speed: 850mm/min
  • Dimension: 8″ x 4.5″ x 13″
  • Gross weight: 16.5 lbs

Search this blog