Here is nice running Hurco CNC Mill. This Mill can be inspected under power in Mpls MN. To set up an inspection or to see a video of this machine, please contact Jim. Note: We will Load on your truck for free. 3 AXIS CNC KNEE MILL. CONTROL: HURCO ULTIMAX II. TABLE SIZE: 38″X12″. TRAVELS CNC: X, Y, Z, 24″, 14″, 5. RAM TRAVEL: MANUAL: 14. KNEE TRAVEL: MANUAL: 15.5. SPEED RANGE: LOW 60-499 RPM. 2 SPEED VARI- DRIVE TRANSMISSION. NOSE TO TABLE DISTANCE MAX: 17.3. MAX WORK LOAD 750#. WIRED 240 VOLT 3 PHASE. 66″W 96″D 89H. Air Oil Mist. ULTIMAX CONTROL AND MAINT. New Hope MN 55428. The item “HURCO KM3P 3 AXIS CNC KNEE MILL Hurco Milling Machine” is in sale since Thursday, May 10, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “jimmers0_0″ and is located in Minneapolis, Minnesota. This item can be shipped to United States.

• Brand: Hurco
• Model: KM3P

Excellent Atlas Index Centers for Atlas 7 Metal Shaper. This indexing pin is missing and the spindle is very stiff from many decades of storage, the crank does not turn easily.. The unit needs a good cleaning and lubrication. These are considered the rarest of Atlas shaper accessories From Original Brochure for the Atlas 7 Shaper: For dividing operations requires in splining, fluting, gear cutting and squaring shafts. Heavy base casting is held to T-slots in shaper by cap screws – support for inner center is cast with base. Outer Center support may be positioned for work up to 8 inches long. Screw with ball crank operates adjustable center. Spindle is locked in position by coordinate clamp. SPECIFICATIONS: 8″ maximum distance between centers, maximum swing 5-1/2″, base 14-1/4″ x 6″ x 7/8 thick. This sale is for Excellent Atlas Index Centers for Atlas 7 Metal Shaper. This indexing pin is missing and the spindle is very stiff from many decades of storage, the crank does not turn easily. These are considered the rarest of Atlas shaper accessories. Please see further pictures below the description. From Original Brochure for the Atlas 7 Shaper: For dividing operations requires in splining, fluting, gear cutting and squaring shafts. A scale shown is for size reference only and not part of the sale. Thank you for looking Please check my other auctions of precision watchmakers, machinists tools and other unique items. All items are described to the best of my ability and questions are encouraged. I have No way to know when and if these charges will be applied. It is understood that by purchasing any item the purchaser assumes all liability and holds harmless and indemnifies JSR & Father Industrial Machinery & Supplies Inc. And its directors against any damage or penalties associated with: 1. Compliance to current or future laws, rules or regulations pertaining to the use or possession of any equipment device or components, 2. Any property damage caused directly or indirectly by the use, operation or possession of any equipment, device or component. Machine Safety: it is the user’s responsibility to provide proper safety devices and equipment to safeguard the operator from harm for any particular use, operation or setup, and to adequately safeguard the machine, or machines, to conform to all Federal, State and Local Government Safety Standards and All Industry Safety Standards. Get images that make Supersized seem small. Track Page Views With. Auctiva’s FREE Counter. The item “RARE Atlas Index Centers Dividing Head for Atlas 7 Metal Shaper” is in sale since Monday, August 20, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “jrwoodca” and is located in Perth, Ontario. This item can be shipped to United States, Canada.

You may also like. Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage: 110 V, 60 Hz. Rotate speed: 0-200 rpm. Length: 33 cm (13 inch). Width: 20 cm (7.9 inch). Height: 18 cm (7 inch). Gross weight: 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. Protective packing material will be added in your package if we believe item can be damaged easily in transit. Tracking numbers will be available in 24 hours except weekends and holidays. Best Prices: By avoiding too many other companies marketing and packaging costs, we deliver the same quality products at a fraction of the cost. Our products are also tested for quality assurance purposes. We trust that you will have a happy experience when shopping with us! We appreciate your business! E-mails are answered Monday through Saturday. Please allow up to 48 hours for a response to your message. The item “Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM” is in sale since Tuesday, August 21, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “niuqiang29″ and is located in cn. This item can be shipped worldwide.

• Brand: VEVOR
• MPN: ZCXZG0085
• Model: AS-250-150
• Country/Region of Manufacture: CHINA
• RPM: 0~200
• TORQUE: 150LBS
• Type: X-axis
• VOLTAGE: 110 V, 60 Hz
• Gross weight: 6.5 kg(14.3 lb)