feed Subscribe to feed
pic
10. 03
2019

As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM

Written by: admin - Posted in: Uncategorized - Tags: , , , , , , , , ,


As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM


As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM


As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM


As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM


As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM


As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM


As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM


As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM


As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM


As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM


As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM


As-250 X Axis Power Feed Knee Mills For Bridgeport Milling Machine 0-200 RPM


Better price, Top Quality, expert Service support. Live demo of multiple products. Owned and operated company. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. AS-250-150 X-Axis Power Feed for Milling Machine X 1. Set of Necessary Accessories X 1. Product Manual X 1. All items are dispatched from our warehouse in Azusa, CA. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. We never want our customers to wait for parts, we have plenty of parts available for every product. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. The item “AS-250 X AXIS POWER FEED KNEE MILLS FOR BRIDGEPORT MILLING MACHINE 0-200 RPM” is in sale since Saturday, March 2, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “ac-racing” and is located in Hacienda Heights, California. This item can be shipped to United States.

  • Brand: AC-RACING
  • Model: AS-250
  • MPN: ZY8LX00361
  • Voltage: 110V, 50/60Hz
  • Rotate speed: 0-200 RPM
  • Torque: 150 lbs
  • Package size: 13″x8″x7″
Tags: , , , , , , , , ,

No Comments

No comments yet.

RSS feed for comments on this post.

Sorry, the comment form is closed at this time.

Search this blog