Z-Axis power feed is made of aluminuml;Power Parameter:90Watt, 110V input voltage, 50/60Hz, single phase;Rotate Speed:0-200 RPM. Max Torque:450in-lb;Max feed rate: 650mm/min; Max return speed: 850mm/min. This power feed fits some milling machines like Bridgeport, Precision Matthews, Enco, Jet, Sharp, Acer, Webb, etc. AUTOMATIC AND MANUAL CONTROL? You can set this power feed to work at automatic constant speed to free your hands or work by manually adjusting the speed control knob to do more precise milling work. And this mulitfunctional milling machine power feed can work with excellent speed control in the entire range according to your needs. This power feed adopts Gleason Spiral Bevel Gear with advantages of stable transmission ratio, low transmission noise, high transmission efficiency and high bearing capacity. And when fast transmission, if the tool collides with the work piece or reverses instantaneously, the special safety device protects the transmission plastic gear and electronic parts from damage. PORTABLE AND EASY TO INSTALL? This power feed for milling machine is compact and portable. Weight: 3.75kg/8.27lbs, Size: 73.512.8 inch. And whether it is for a novice or a skilled operator, it is very easy to install this power feed according to the instruction and online video or by yourself. This milling table power feed fits some vertical knee type mills with the same mounting pattern and a 5/8 diameter shaft on the end, But it will NOT fit mills with a different mounting pattern or different sized leadscrews like powermatic and some other odd sized machines, so please make sure yours is the typical Bridgeport type as mentioned above. Rotate Speed: 0-200 RPM. Max Torque: 450 in-lb. Max Feed Rate: 650 mm/min. Max Return Speed: 850 mm/min. Dimension: 8″x4.5″x13. Package Size: 11.8″x8.7″x13.8. Gross Weight: 16.5 lbs. 1 x Power Feed Z-axis for Milling Machine. 1 x Copper Gear & 1 x Flat Key Pin. 2 x Limit Block. 15 x Round Flat Washer. 1 x Nominal Diameter. 4 x Install Screw. 1 x Limit Switch Box. 2 x Limit Switch Spring+1 x Handle Spring. 1 x Bearing Inner Ring. 1 x Connecting Rod & 1 x Flange.

WIDE APPLICATION? Designed to fit milling machines such as Bridgeport, Precision Matthews, Enco, Jet, Sharp, Acer, Webb, and more, this power feed is versatile. Whether you are a novice or a skilled operator, installing this power feed is a breeze.

1 x Power Feed Z-axis for Milling Machine. Max Torque: 450 in-lb. Max Feed Rate: 650 mm/min. Rotate Speed: 0-200 RPM. 1 x Copper Gear & 1 x Flat Key Pin. 2 x Limit Switch Spring+1 x Handle Spring. 1 x Connecting Rod & 1 x Flange.

1 x Power Feed Z-axis for Milling Machine. Max Torque: 450 in-lb. Max Feed Rate: 650 mm/min. Rotate Speed: 0-200 RPM. 1 x Copper Gear & 1 x Flat Key Pin. 2 x Limit Switch Spring+1 x Handle Spring. 1 x Connecting Rod & 1 x Flange.

1 x Power Feed Z-axis for Milling Machine. Max Torque: 450 in-lb. Rotate Speed: 0-200 RPM. 1 x Copper Gear & 1 x Flat Key Pin. Max Feed Rate: 650 mm/min. 1 x Connecting Rod & 1 x Flange. 2 x Limit Block.

For more information on our products. Please send message to us. AS-250 150Lbs Torque Power Feed Milling Machine X-Axis ALSGS 0-200RPM. What Customers Have To About Us. Just As It Says, Got here fast. Have not used yet. Can’t wait to use it. Item was received quickly and was exactly as described. THANKS to a great Ebayer. “5++ Stars the product works wonders”. Extremely professional, takes care of cust. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). 110 V, 60 Hz. 33 cm (13 inch). 20 cm (7.9 inch). 18 cm (7 inch). 6.5 kg(14.3 lb). AS-250-150 X-Axis Power Feed for Milling Machine. Set of Necessary Accessories. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. All items are dispatched from our warehouse in HACIENDA HEIGHTS, CA. Some products may be dispatched in more than one carton. International Buyers – Please Note. If you have a problem with the product. We will require a picture of the damaged part for verification. We offer detailed product descriptions and images to give you a real advantage in finding the products you’re looking for. 25 years Industry Experience. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “happystore-01″ and is located in this country: US. This item can be shipped to United States.

• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13\
• Gross weight: 6.5 kg(14.3 lb)
• Warranty: Lifetime
• UPC: 0895800908447
• EAN: 0895800908447
• Brand: VEVOR
• Function: Milling
• Control: Manual
• Machine Type: Milling Machine
• Power Source: Electric
• Max Spindle Speed (RPM): 200 RPM
• Voltage: 110 V
• Model: AS-250
• MPN: ZCXUN00525

The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Please contact our customer service team immediately if: 1. You changed your mind and wish to request a return. Your product was damaged during transit. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “fansdealonline” and is located in this country: US. This item can be shipped to United States.

• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13\
• Gross weight: 6.5 kg(14.3 lb)
• Warranty: Lifetime
• UPC: 0895800908447
• EAN: 0895800908447
• Brand: VEVOR
• Function: Milling
• Control: Manual
• Machine Type: Milling Machine
• Power Source: Electric
• Max Spindle Speed (RPM): 200 RPM
• Voltage: 110 V
• Model: AS-250
• MPN: ZCXUN00525

Better price, Top Quality, expert Service support. Live demo of multiple products. Owned and operated company. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. AS-250-150 X-Axis Power Feed for Milling Machine X 1. Set of Necessary Accessories X 1. Product Manual X 1. All items are dispatched from our warehouse in CANJAL. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. We never want our customers to wait for parts, we have plenty of parts available for every product. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. The item “Power Feed X-Axis 150 Lbs Torque For Bridgeport Type Milling Machines 0-200 RPM” is in sale since Thursday, March 11, 2021. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “best-homepro” and is located in Westbury, New York. This item can be shipped to United States.

• Brand: BEST-HOMEPRO
• Model: AS-250-150
• MPN: ZY8LX00361
• Voltage: 110V
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″
• Gross weight: 6.5 kg(14.3 lb)
• Warranty: 5 Years
• Function: Milling
• Machine Type: Milling Machine
• Power Source: Electric
• Control: Manual

The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Your product was damaged during transit. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that¡¯s why our customers keep coming back. The item “AS-250 X AXIS POWER FEED KNEE MILLS FOR BRIDGEPORT MILLING MACHINE 0-200 RPM” is in sale since Friday, March 5, 2021. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “vipshopmarket” and is located in Westbury, New York. This item can be shipped to United States.

• Voltage: 110V
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″
• Gross weight: 6.5 kg(14.3 lb)
• Warranty: 5 Years
• Function: Milling
• Machine Type: Milling Machine
• Power Source: Electric
• Control: Manual
• Brand: VEVOR
• Model: AS-250-150
• MPN: ZCXZG0085

The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Your product was damaged during transit. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that¡¯s why our customers keep coming back. The item “Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM” is in sale since Tuesday, December 15, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “vipshopmarket” and is located in Westbury, New York. This item can be shipped to United States.

• Brand: VIPSHOPMARKET
• Model: AS-250-150
• MPN: ZY8LX00361
• Voltage: 110V
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″
• Gross weight: 6.5 kg(14.3 lb)
• Warranty: 5 Years
• Function: Milling
• Machine Type: Milling Machine
• Power Source: Electric
• Control: Manual