Sign up to Newsletters. X-Axis Power Feed 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage: 110 V, 60 Hz. Rotate speed: 0-200 rpm. Length: 33 cm (13 inch). Width: 20 cm (7.9 inch). Height: 18 cm (7 inch). Gross weight: 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “AS-250 150Lbs Torque Power Feed Milling Machine X-Axis ALSGS L. A. Ship 0-200RPM” is in sale since Monday, September 11, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “supply2worldwide” and is located in Ontario, California. This item can be shipped to United States, all countries in Europe, Mexico, Australia.

• Brand: VEVOR
• MPN: g787400924
• Model: AS-250-150
• Country/Region of Manufacture: CHINA
• RPM: 0~200
• TORQUE: 150LBS
• Type: X-axis
• VOLTAGE: 110 V, 60 Hz
• Gross weight: 6.5 kg(14.3 lb)

Best ALB-310 Horizontal 110V/220V power feed. Note:The shaft is 16mm. It is a very useful power feed system for the X axis to provide a smooth, variable speed drive to the travers of the table. This will enable control of the cut finish to a much greater extent than achievable by hand. With simple controls for left/right movement, auto stop in any position on the table provided by movable stops, overload protection and a fast traverse button giving 40 per min speed. Simple to fit and powered by a standard 110V/220V plug, so no wiring is required. If item Defective after 12 Month, Buyers can still send it back for repair. The item “Best price! ALSGS ALB-310 Horizontal 110V 220V power feed milling free shipping” is in sale since Friday, August 3, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “88490755″ and is located in China. This item can be shipped worldwide.

• Model: ALB-310
• Modified Item: No
• Country/Region of Manufacture: China
• Custom Bundle: No
• MPN: No have
• Brand: ALSGS
• Non-Domestic Product: No

Sign up to Newsletters. Brand New AL-310S X-Axis Power Feed Kit For Milling Machine. Our Brand New AL-310S X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). To stop jog operating, you must first turn FEED KNOB to 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Brand new power feed. X traverse (left-right travel). Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Rotate speed: 0-200 RPM. Max torque: 450 in-lb. Max feed rate: 650mm/min. Max return speed: 850mm/min. Dimension: 8 x 4.5 x 13 inches. Package size: 11.8 x 8.7 x 13.8 inches. Gross weight: 16.5 lbs. 1 x Power Feed For Milling Machine. 8 x Adjustable Pad. 2 x Tiavel Stop Assembly. 1 x Bevel Gear. 1 x Dial Nut. 1 x Locking Nut. 1 x Product Manual. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “Best price ALSGS AL-310 110V 220V Power feed for Vertical milling machine X axis” is in sale since Wednesday, October 18, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “houxiaoxi0i-4″ and is located in Ontario, California. This item can be shipped to United States, Canada, Germany.

• Brand: VEVOR
• MPN: LXQIC009
• Bundle Listing: Yes
• Model: AL-310S
• Country/Region of Manufacture: CHINA
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Max torque: 450 in-lb
• Max feed rate: 650mm/min
• Max return speed: 850mm/min
• Dimension: 8 x 4.5 x 13 inches
• Gross weight: 16.5 lbs

Power Feed X-Axis 450 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. AL-310S X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed adjust knob Speed can be adjust according to operator’s requirement, ranging from 0-9. Jog switch Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). To stop jog operating, you must first turn “FEED KNOB” to “0″(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Brand new power feed. X traverse (left-right travel). Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Type : X traverse (Left-Right Travel). Rotate speed : 0-200 RPM. Max torque : 450 in-lb. Max feed rate : 650mm/min. Max return speed : 850mm/min. Dimension : 8 x 4.5 x 13 inches. Gross weight : 16.5 lbs. Power Feed For Milling Machine x 1. Tiavel Stop Assembly x 2. Why shop with us? All items are dispatched from our warehouse in HACIENDA HEIGHTS, CA. Some products may be dispatched in more than one carton. International Buyers – Please Note. Please do check everything carefully when receiving the package. Failure to do so might result in damage to your own rights and interests. If you have a problem with the product. We offer detailed product descriptions and images to give you a real advantage in finding the products you’re looking for. With our comprehensive parts support, we help to keep your unit humming. The item “HOT ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX US FAST” is in sale since Tuesday, July 17, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “pestech” and is located in Hacienda Heights, California. This item can be shipped to United States.

• Brand: pestech
• Model: AL-310S
• MPN: ZY8LX00363
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Max torque: 450 in-lb
• Max feed rate: 650mm/min
• Max return speed: 850mm/min
• Dimension: 8″ x 4.5″ x 13″
• Gross weight: 16.5 lbs

ALSGS ALB – 310 Horizontal 110V 220V Power Feed Table For Milling Machine X Y Z. Milling machine X axis. A very useful power feed system for the X axis to provide a smooth, variable speed drive to the traverse of the table. This will enable control of the cut finish to a much greater extent than achievable by hand. With simple controls for left/right movement, auto stop in any position on the table provided by movable stops, overload protection and a fast traverse button giving 40 per min speed. Simple to fit and powered by a standard 230V three pin plug, Or 110V so no wiring is required. For ZX series mills only. Item includes: 1AL-310S Horizontal power feed. There are 110V and 220V, please leave a massage to us when place the order, if not we will send the. It includes accessories for installion. There are X, Y, Z axis power feed for choose from, we will send X aixs one if not specify. We reserve the right to cancel any order for any reason at any time. We are not responsible for undeliverable addresses. Your feedback very important to us, after you get your package and you are. Satisfied with our sevice. If you have any problem with your order / any questions please before leave any type of feedback. Thank you for shopping at our store. The item “ALSGS ALB 310 Horizontal 110V 220V Power Feed Table For Milling Machine X Y Z” is in sale since Friday, April 6, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “discountparts_90″ and is located in Hong Kong. This item can be shipped worldwide.

• Color: Silver
• Manufacturer: Dani
• Model: ALB-310
• Brand: Does not apply
• UPC: Does not apply
• ISBN: Does not apply
• EAN: Does not apply
• MPN: Does not apply

Power Feed APF-500X Torque for Type Milling Machines 0-210 RPM Feeding Device. You are looking at our new Power Feed X for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. 107T for plastic transmission gear and 6T for motor shaft gear 107 is not divisible by 6, 107 % 6 = 17.8333333333… The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Set the fix stand on work table, set table bearing bushing on the axis screw, then set the power table feed on the fix stand, take out the gear housing. Use one hand to hold the center transmission shaft. Set the bevel gear on axis screw with the other hand. Then check if the backlash between gears is between 0.1-0.2mm. Add shims (1.0t, 0.25t, 0.1t) if the backlash is too large. Repeat step 2-3 until reaching satisfying backlash. Tighten the handle to start setting socket parallel key and bevel gear. Rotate the handle slightly to feel if any interfere occurs in between. If do, please repeat step 3-4 to add more shims. If not, go to next step. Take out the handle, add proper shim (43×33), adjust the backlash between dial & bevel gear and lock with fix ring. Set the handle and tighten, slightly rotate the handle. Normally it should be smooth without any interfere. Finally, set the gear housing and limit switch. Power supply switch and reset switch. The right side of power switch is ON. The left side is OFF. Red light will show when machine is on. The red round button on right side is reset switch. Reset button will jump up to cut off the power if the machine overloads. The operator must reduce cutting load, then press reset switch to continue operating. Feed knob and rapid button. Rotate feed knob after power is on. Turn left for left side feeding and vice versa. The button in the middle is rapid button. Tool will travel rapidly to left side if you keep pressing the button. Release to make power table feed will back to normal speed. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. NOTE: To stop jog operating, you must first turn FEED KNOB TO 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Add an auto power table feed to your milling machine. A simple and inexpensive way to increase productivity. Small volume and easy installation. Excellent speed control in the entire range. Jog function operates at any feed speed. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Package Dimensions: 11713(275175335mm). 1 x X-Axis Fix Stand with Bushing. 1 x Bevel Gear with Fix Ring. 1 x Handle Washer. 2 x Stop Blocks. 2 x Stop Set. 2 x Socket Screws (M8P1.2535). X Socket Screws M8P1.0. 6 x Small Shims. 2 x Small Shims 26.2. 3 x Small Shims 26.2. 4 x Large Shims. 2 x Spring Pins. 1 x Cable Clamp. 1 x User Manual. Sign up to newsletter. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “Best price! ALSGS APF-500X Horizontal 110V power feed milling free shipping” is in sale since Thursday, April 13, 2017. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “technology-etrade” and is located in Ontario, California. This item can be shipped to United States, all countries in Europe, Canada, Mexico, Australia.

• Brand: VEVOR
• MPN: 4AZY8008
• Model: APF-500X
• Country/Region of Manufacture: CHINA
• Torque: 135lbs
• Weight: 13.2lbs
• Color: White
• Current: 2.8A
• R.P.M.: 0-210
• Package Dimension: 11 x 7 x 13 inch

For more information on our products. Please send message to us. Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. What Customers Have To About Us. ” Delivered as promised and item is as described “. Just what i was looking for. Had a problem-was able to successfully resolve it. AL-310S X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8in Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed adjust knob Speed can be adjust according to operator’s requirement, ranging from 0-9. Jog switch Normally, jog switch should be at FEED position. For jog movement, just switch to 0 position. Kept holding the switch until it travels to requires position. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). To stop jog operating, you must first turn “FEED KNOB” to “0″(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. X traverse (Left-Right Travel). 8 x 4.5 x 13 inches. Power Feed For Milling Machine. Brand new power feed. X traverse (left-right travel). Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. All items are dispatched from our warehouse in Azusa, CA. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Your product was damaged during transit. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. 25 years Industry Experience. The item “ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA” is in sale since Saturday, June 23, 2018. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “fans-autoparts” and is located in Hacienda Heights, California. This item can be shipped to United States.

• Brand: FANS-AUTO
• Model: AL-310S
• MPN: ZY8LX00363
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Max torque: 450 in-lb
• Max feed rate: 650mm/min
• Max return speed: 850mm/min
• Dimension: 8″ x 4.5″ x 13″
• Gross weight: 16.5 lbs

ALB-310SX X-Axis Power Feed Milling Drill Machine 200RPM 450in-lb 110V / 220V Product parameters – Name: electronic power feed, electronic feeders – Model: ALB-310SX (Horizontal) – Main motor power: 95w – Speed range: 0-200 – Maximum speed: 200RPM – Maximum torque: 450in-lb – Power Requirements: AC110V / AC220V, 50 / 60HZ (optional) – Applicable models: vertical turret milling machines, drilling and milling machine, other machinery. Milling machine power feeding easy to install with low noise, large torque, high speed, convenient installation and flexible operation, good appearance, as to meet the requirements of ergonomics. We plug is three categories: US plug, UK plug, European plug. Our product is the default US plug. Please do tell us the needed voltage and the Plug type when you place order Package Content: 1 x ALB-310SX X-Axis Power feed Milling drill Machine 200RPM 450in-lb 110V / 220V (as picture). International buyers please note: a. These charges are buyers responsibility. The item “ALSGS 110V/220V Power Feed for Vertical Milling Machine X Y Axis ALB-310SX” is in sale since Thursday, January 25, 2018. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “cybereveryday” and is located in HK. This item can be shipped worldwide.

• Brand: Unbranded/Generic
• MPN: Does Not Apply
• Model: ALB-310SX
• Main motor power: 95w
• Speed range: 0-200
• Power Requirements: AC110V / AC220V, 50 / 60HZ (optional)

Sign up to Newsletters. Brand New AL-310S X-Axis Power Feed Kit For Milling Machine. Our Brand New AL-310S X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). To stop jog operating, you must first turn FEED KNOB to 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Brand new power feed. X traverse (left-right travel). Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Rotate speed: 0-200 RPM. Max torque: 450 in-lb. Max feed rate: 650mm/min. Max return speed: 850mm/min. Dimension: 8 x 4.5 x 13 inches. Package size: 11.8 x 8.7 x 13.8 inches. Gross weight: 16.5 lbs. 1 x Power Feed For Milling Machine. 8 x Adjustable Pad. 2 x Tiavel Stop Assembly. 1 x Bevel Gear. 1 x Dial Nut. 1 x Locking Nut. 1 x Product Manual. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In USA” is in sale since Wednesday, October 18, 2017. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “popularitemstore” and is located in Ontario, California. This item can be shipped to United States, Canada, Germany.

• Brand: Vevor Gewindebohren
• MPN: ZY8LX00363
• Bundle Listing: Yes
• Model: AL-310S
• Country/Region of Manufacture: CHINA
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Max torque: 450 in-lb
• Max feed rate: 650mm/min
• Max return speed: 850mm/min
• Dimension: 8 x 4.5 x 13 inches
• Gross weight: 16.5 lbs

ALSGS 110V 220V Power Feed for Vertical Milling Machine X Y Axis AL-310SX. Item include: 1AL-310 power feed for X axis. It includes accessories for installion. The item “ALSGS Power Feed for Vertical Milling Machine 110V X Y Axis AL-310SX In US STOCK” is in sale since Friday, July 29, 2016. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “goodlucksell” and is located in Walton, Kentucky. This item can be shipped to United States.

• Brand: Unbranded
• MPN: Does Not Apply