MOTOR FOR BRIDGEPORT VARIABLE SPEED HEAD WITH 1.5 HP MOTOR. THIS MOTOR HAS BEEN CLEANED AND ASSEMBLED WITH NEW BEARINGS AND FACTORY PAINT. FULLY TESTED IN GOOD CONDITION. SHAFT DIAMETER IS 15/16 OR.

Item has been previously owned but is in great condition. Photos were taken as best as possible. Outside packaging may have distress. Distress can include scuffs, scratches, dents, tears, holes, or marking of any kind, see pictures. Please look through photos carefully prior to purchasing. Item is used and I believe it is missing a spring on the end shown in the last photo is a comparison of a new one with the spring and the current listing without the spring. Thank you for your patience and understanding as we balance work and family time. We will solve any problems quickly and efficiently! We will choose the quickest option.

4PCS stepper motor drivers DQ542MA 4.2A 50VDC 125Microsteps. 2PCS power supply 350W 36V. 3.0Nm(425oz. In). Stepper Motor Driver DQ542MA. DQ542MA is a type of two-phase hybrid stepping motor driver, The drive voltage of which is from 18VDC to 50VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Holding torque when DQ542MA runs under high speed, is also significantly higher than the other two-phase driver, what’s more. The positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine. CNC machine, Computer embroider machine, packing machines and so on. High performance, low price. Average current control, 2-phase sinusoidal output current drive. Supply voltage from 18VDC to 50VDC. Overvoltage, under voltage, overcurrent, phase short circuit protection. 15 channels subdivision and automatic idle-current reduction. 8 channels output phase current setting. Offline command input terminal. Motor torque is related to speed, but not related to step/revolution. High holding torque under high speed. Not condensation, no water droplets. Prohibition of combustible gases and conductive dust. POWER SUPPLY 350W 36V. 350W Single Output Switching Power Supply. AC input range selected by switch. Protections:short circuit/overload/over voltage/over temperature. 100% full load burn-in test. Low cost, high reliability. AC input voltage range: 90. AC inrush current: cold start 25A/115V, 50A/230V. DC adjustment range:±10% rated output voltage. 135%, hiccup mode, auto recovery. Setup, rise, hold up time: 200ms, 50ms, 20ms/230VAC at full load. Working temperature and humidity:-10? Set pins according to software as follows. Output pin: P1, P2, P3, P4, P5, P6, P7, P8, P9, P14, P16, P17. P2 – X axis Pulse, P3 – X axis Direction. P4 – Y axis Pulse, P5 – Y axis Direction. P6 – Z axis Pulse, P7 – Z axis Direction. P8 – A axis Pulse, P9 – A axis Direction. P14 – B axis Pulse, P1- B axis Direction. P16 – C axis Pulse, P17- C axis Direction. Input pin: P10, P11, P12, P13, P15. Set them for Emergency Stop and X Y Z Limit switch.

For sale is a drive motor cable set. These are not chinese but used OEM HAAS cables.

MicroKinetics Micro Mill Mighty Drive MN400E Motor Control Sherline Drive control for MicroKinetics motors. Originally came from a Sherline micro mill, works fine. Includes both the Mighty Drive Spindle box as well as the MN400E control box (which has USB).

USED, MOTOR PULLEY FOR THE M HEAD. I PUT IT ON A MOTOR AND THE PULLEY RUNS FINE. NO EXCEPTIONS; NO MATTER HOW CLOSE YOU THINK YOU LIVE TO MY LOCATION.

With MT3 Collet Set , MT3 Milling machine is equipped with a set of MT3 collets set. Chuck × 8 (4-3, 5-4, 6-5, 8-7, 10-9,12-11,14-13,16-15) , wrench × 1 , handle × 1. RCOG-25V Brushless Precision Milling and Drilling Machine 110V 1100W Spindle Taper MT3.

Pulled from a dismantled vmc40. This is the second one from this machine. Functionality is guaranteed for 30 days.

IT IS3 PHASE ; 220V; 1/2HP; 1200 RPM. THE SWITCH MOUNT BRACKET HAS BEEN BRAZED (SEE PICTURES). I HOOKED THE MOTOR UP TO POWER AND IT RUNS. I CAN FEEL A LITTLE VIBRATION WHEN THE MOTOR IS RUNNING.

Application:Mainly used in CNC machine tool industry, automated production line and other high-precision positioning transmission industry.