4PCS stepper motor drivers DQ542MA 4.2A 50VDC 125Microsteps. 2PCS power supply 350W 36V. 3.0Nm(425oz. In). Stepper Motor Driver DQ542MA. DQ542MA is a type of two-phase hybrid stepping motor driver, The drive voltage of which is from 18VDC to 50VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Holding torque when DQ542MA runs under high speed, is also significantly higher than the other two-phase driver, what’s more. The positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine. CNC machine, Computer embroider machine, packing machines and so on. High performance, low price. Average current control, 2-phase sinusoidal output current drive. Supply voltage from 18VDC to 50VDC. Overvoltage, under voltage, overcurrent, phase short circuit protection. 15 channels subdivision and automatic idle-current reduction. 8 channels output phase current setting. Offline command input terminal. Motor torque is related to speed, but not related to step/revolution. High holding torque under high speed. Not condensation, no water droplets. Prohibition of combustible gases and conductive dust. POWER SUPPLY 350W 36V. 350W Single Output Switching Power Supply. AC input range selected by switch. Protections:short circuit/overload/over voltage/over temperature. 100% full load burn-in test. Low cost, high reliability. AC input voltage range: 90. AC inrush current: cold start 25A/115V, 50A/230V. DC adjustment range:±10% rated output voltage. 135%, hiccup mode, auto recovery. Setup, rise, hold up time: 200ms, 50ms, 20ms/230VAC at full load. Working temperature and humidity:-10? Set pins according to software as follows. Output pin: P1, P2, P3, P4, P5, P6, P7, P8, P9, P14, P16, P17. P2 – X axis Pulse, P3 – X axis Direction. P4 – Y axis Pulse, P5 – Y axis Direction. P6 – Z axis Pulse, P7 – Z axis Direction. P8 – A axis Pulse, P9 – A axis Direction. P14 – B axis Pulse, P1- B axis Direction. P16 – C axis Pulse, P17- C axis Direction. Input pin: P10, P11, P12, P13, P15. Set them for Emergency Stop and X Y Z Limit switch.

4PCS stepper motor drivers DQ542MA 4.2A 50VDC 125Microsteps. 2PCS power supply 350W 36V. 3.0Nm(425oz. In). Stepper Motor Driver DQ542MA. DQ542MA is a type of two-phase hybrid stepping motor driver, The drive voltage of which is from 18VDC to 50VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Holding torque when DQ542MA runs under high speed, is also significantly higher than the other two-phase driver, whats more. The positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine. CNC machine, Computer embroider machine, packing machines and so on. High performance, low price. Average current control, 2-phase sinusoidal output current drive. Supply voltage from 18VDC to 50VDC. Overvoltage, under voltage, overcurrent, phase short circuit protection. 15 channels subdivision and automatic idle-current reduction. 8 channels output phase current setting. Offline command input terminal. Motor torque is related to speed, but not related to step/revolution. High holding torque under high speed. Not condensation, no water droplets. Prohibition of combustible gases and conductive dust. POWER SUPPLY 350W 36V. 350W Single Output Switching Power Supply. AC input range selected by switch. Protections:short circuit/overload/over voltage/over temperature. 100% full load burn-in test. Low cost, high reliability. AC input voltage range: 90. AC inrush current: cold start 25A/115V, 50A/230V. DC adjustment range:±10% rated output voltage. 135%, hiccup mode, auto recovery. Setup, rise, hold up time: 200ms, 50ms, 20ms/230VAC at full load. Working temperature and humidity:-10. Set pins according to software as follows. Output pin: P1, P2, P3, P4, P5, P6, P7, P8, P9, P14, P16, P17. P2 X axis Pulse, P3 X axis Direction. P4 Y axis Pulse, P5 – Y axis Direction. P6 Z axis Pulse, P7 Z axis Direction. P8 – A axis Pulse, P9 – A axis Direction. P14 – B axis Pulse, P1- B axis Direction. P16 – C axis Pulse, P17- C axis Direction. Input pin: P10 , P11, P12, P13, P15. Set them for Emergency Stop and X Y Z Limit switch. The item “US Nema23 stepper motor 435oz+driver DQ542MA 18-50V+Power supply350w 36v” is in sale since Monday, July 27, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “cncmotor111″ and is located in Rowland Heights, California. This item can be shipped worldwide.

• Machine Type: Milling Machine
• Power Source: Electric
• MPN: Does Not Apply
• Function: Drilling
• Brand: wantai
• Control: Automatic
• Voltage: 36v/48VDC

CNC Spindle Motor & Tool Parts. Stepper Motor & Driver. Servo Motor & Driver. HMI & PLC Panel. CNC Router & Tools. Rotary 4th Axis 100mm 3-jaw Lathe Chuck Nema23 Stepper for CNC Router Engraver. Rotary 4th Axis F100mm 3-jaw Lathe Chuck Nema23 Stepper for CNC Router Engraver. (1), CNC 4th axis (A aixs, Rotary axis) with chuck for cnc router cnc miiling machine (2), hollow shaft Rotary axis 3 Jaw 100mm chuck CNC 4th Axis CNC dividing head for cnc router (3), Rotation 6:1 A axis for Mini CNC router/engraver woodworking engraving machine. K11 100MM 3-jaw chuck. 0.3 degrees / step. 6:1 (Synchronous belt). Two phase 57 NEMA23 stepper motor. 4th axis pulse equivalent SETUP. Of pulses of 1 Degree. Number of pulses of Motor/lap. Micro-stepping levels of Drive reduction ratio/360 degree. Two phase Nema23 Motor. Control card system setting. The angle of one-pulse. Micro-stepping levels of Drive reduction ratio. 360÷(200×16×50)=0.00225. The replace algorithm of X or Y Axis. Peremeter (number of pulses of Motor/lap micro-stepping levels of Drive reduction ratio). Feedback is very important to us. So that we can address your concerns. It is impossible to address issues if we do not know about them! Your satisfaction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. If you need any CNC parts or repairs, welcome to contact me, we will try our best to help you. If it’s non-workdays, please kindly be patient and wait till Monday. The item “Rotary 4th Axis 100mm 3-jaw Lathe Chuck Nema23 Stepper for CNC Router Engraver” is in sale since Monday, September 12, 2016. This item is in the category “Business, Office & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “vipwindows_168″ and is located in Shenzhen. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

• Brand: Unbranded/Generic
• Model: K11-100 Hollow Shaft
• MPN: Does Not Apply
• Axis: Rotary Axis , 4th Axis
• EAN: Does not apply

CNC Spindle Motor & Tool Parts. Stepper Motor & Driver. Servo Motor & Driver. HMI & PLC Panel. CNC Router & Tools. 4th 5th CNC Dividing Head Rotary Axis Nema23 Stepper Motor Rotation Axis 6:1 8:1. 4th 5th CNC Dividing Head Ratio 6:1 8:1 Stepper Motor Rotary Rotation Axis CNC Engraving Router. (1) CNC5th axis (A aixs, Rotary axis) with chuck fo CNC router cnc miiling machine (2) Rotation 6:1 A axis for Mini CNC router/engraver woodworking engraving machine. The output diameter of shaft. 6:1 and 8:1. Two phase 57mm 3A NEMA23 stepper motor. 5th axis pulse equivalent SETUP. Number of pulses of 1 Degree. (number of pulses of Motor/lap micro-stepping levels of Drive reduction ratio)/360 degree. Such as: Two phase Nema23 Motor micro-stepping levels: 16 reduction ratio:50. Control card system settings. The angle of one-pulse. 360 degree/(number of pulses of Motor/lap micro-stepping levels of Drive reduction ratio). Such as : Two phase Nema23 Motor micro-stepping levels : 16. 360÷(200×16×50)=0.00225. The replace algorithm of X or Y Axis. Perimeter/(number of pulses of Motor/lap micro-stepping levels of Drive reduction ratio). Feedback is very important to us. So that we can address your concerns. It is impossible to address issues if we do not know about them! Your satisfaction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. If you need any CNC parts or repairs, welcome to contact me, we will try our best to help you. If it’s non-workdays, please kindly be patient and wait till Monday. The item “4th 5th CNC Dividing Head Rotary Rotation Axis Nema23 Stepper Motor fr CNCRouter” is in sale since Monday, May 8, 2017. This item is in the category “Business, Office & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “vipwindows_168″ and is located in Shenzhen. This item can be shipped to all countries in Europe, all countries in continental Asia, United States, Canada, Australia.

• Brand: Unbranded/Generic
• MPN: Does Not Apply
• UPC: Does not apply