Grinding Disc Crusher Grinding machine. The small disc mill crusher is a piece of high-efficiency equipment specifically designed for grinding and crushing ore materials. By means of its compact structure, flexible operation and stable performance, it is widely used in the scenarios such as laboratory sample preparation, small-scale mining processing and building material testing. It can precisely crush various kinds of ore (such as iron ore, limestone and granite) to meet material processing requirements with different fineness demands. Material of grinding disc: Manganese steel Voltage: 220V 50/60Hz 1PH Motor power: 1500W Driving mode: Belt driving (including a belt cover) Finished product collecting mode: Bottom collecting box Grinding fineness adjusting mode: Use the handwheels to adjust the gap between the grinding discs. Is integrally made of cast iron, stably supports the whole machine, ensures there is no obvious shake during operation and guarantees the grinding precision. Manganese steel grinding disc assembly. Comprises upper and lower manganese steel grinding discs rotating relatively, and is a core part for material crushing. The manganese steel material improves the grinding efficiency and wear resistance. Is composed of a 1.5KW 220V motor, belt pulley and driving belt. After the motor runs, the grinding discs are driven by the belt to rotate so as to grind the material. The belt cover is arranged outside the driving system to avoid the phenomenon that the belt is exposed to cause potential safety hazards. Is composed of an adjusting handwheel, adjusting screw rod and other components. The handwheel can be rotated to drive the screw rod to adjust the gap between the grinding discs, and then the material crushing fineness can be controlled. Is located on the top of the machine. The funnel design is adopted, facilitating material feeding. Meanwhile, the feeding speed can be controlled to avoid the phenomenon that due to too fast feeding, the machine is overloaded. Finished product collecting box. Is installed at the bottom of the machine and abuts against the discharging outlet below the grinding discs. The crushed material automatically falls into the collecting box. The collecting box adopts the pull-out or flip type design, so it is conveniently taken out and cleaned. Installation of collecting box. Operator requirements: Operators must be familiar with the contents of this manual and master the equipment operation methods and safety precautions before they can start working. Non-professionals are strictly prohibited from operating the equipment without authorization, and children are prohibited from touching and operating the machine. Power safety: The equipment must use the 220V single-phase AC power supply that meets the requirements, and the leakage protection device must be installed. It is strictly prohibited to operate the power switch with wet hands to avoid electric shock accidents. When the device is running, it is forbidden to plug or unplug the device. Protective measures: When the equipment operates, the belt cover must be installed in place, and it is strictly prohibited to start the equipment under the condition that the belt cover is not installed or is damaged. It is strictly prohibited to stretch hands or other objects into the feeding inlet, the gap between the grinding discs, and belt driving part to prevent the personal injury. During operation, wear a protective face mask to prevent splashing. Material safety: It is strictly prohibited to feed the too hard materials such as metal blocks and stones, or flammable, explosive or corrosive materials to avoid damaging the equipment or causing safety accidents. The material should be fed slowly and evenly to avoid material blockage in the feeding inlet. After the equipment is completely stopped, the fault should be checked and dealt with. The equipment must not be restarted before the fault is not solved. Equipment placement: The equipment should be placed on a flat and solid ground to avoid tilting and prevent the equipment from falling down during operation. The adequate space should be reserved around the equipment (it is recommended that the space should be no less than 0.5m) for convenient operation, maintenance and heat dissipation. Item included:Grinding Disc Crusher Grinding machine 1 Item Number: 134181. Orders are processed from Monday-Friday; Not on the weekends & public holidays. We will work with you to get the case resolved in the fastest method. Hope for your understanding. Please contact with us at first for more details. Defective & Damaged Products. If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, it’s much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. If an item is received damaged, customer service must be contacted within 7 days of receiving your item. Payments via eCheck do not clear immediately. Usually you will wait 5-7 days after checkout for it to clear.

Name : Milling machine tool feeder Model : APF-500 Voltage : AC 220V Current : 2.8 A Speed : 210 rpm Speed adjustment range : 0-210 rpm Torque : 650IN-LB. Using a new type of clutch device. High precision, low noise. New patent, waterproof and dustproof. Collision protection function. Strengthen torque and increase low-speed torque. 0.2 second sudden stop. 1x A set of APF500 tool feeder.

220V 450W 600W 750W 1100W DC Motor Special Motor for Milling / Lathe Machine.

Specifications: Type: X Voltage: 220V, 50/60Hz Current: 2.8A Max. Torque: 155kg/cm, 135lb/in R. 0-210 Gross Weight: 6kg Package Dimensions: 291027cm Package Content 1 x APF-260 Power Feed 1 x X-Axis Fix Stand with Bushing 1 x Bevel Gear with Fix Ring 1 x Handle Washer 2 x Stop Blocks 2 x Stop Set 2 x Socket Screws (M8P1.2535) 2 x Socket Screws (M8P1.025) 6 x Small Shims (F26.2F16.20.25t) 2 x Small Shims (F26.2F16.20.1t) 3 x Small Shims (F26.2F16.21.0t) 4 x Large Shims (F43.4F33.40.25t) 2 x Spring Pins 1 x Cable Clamp 1 x User Manual. X Axis Power Feed Table Milling Machine Fit Bridgeport Type Mill Power feed 220V. Please provide the machine type picture before placing the order to judge whether the product meets your needs. The hole diameter of the gear is 16mm. The size of the center hole to the bottom is about 220mm. Set the fix stand on work table, set table bearing bushing on the axis screw, then set the power table feed on the fix stand, take out the gear housing. Use one hand to hold the center transmission shaft. Set the bevel gear on axis screw with the other hand. Then check if the backlash between gears is between 0.1-0.2mm. Add shims (1.0t, 0.25t, 0.1t) if the backlash is too large. Repeat step 2-3 until reaching satisfying backlash. Tighten the handle to start setting socket parallel key and bevel gear. Rotate the handle slightly to feel if any interfere occurs in between. If do, please repeat step 3-4 to add more shims. If not, go to next step. Take out the handle, add proper shim (f43xf33), adjust the backlash between dial & bevel gear and lock with fix ring. Set the handle and tighten, slightly rotate the handle. Normally it should be smooth without any interfere. Finally, set the gear housing and limit switch. Power supply switch and reset switch. The right side of power switch is “ON”. The left side is OFF. Red light will show when machine is on. The red round button on right side is reset switch. Reset button will jump up to cut off the power if the machine overloads. The operator must reduce cutting load, then press reset switch to continue operating. Feed knob and rapid button. Rotate feed knob after power is on. Turn left for left side feeding and vice versa. The button in the middle is “rapid button”. Tool will travel rapidly to left side if you keep pressing the button. Release to make power table feed will back to normal speed. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. NOTE: To stop jog operating, you must first turn “FEED KNOB” TO “0″(OFF) position. Then move “JOG SWITCH” to “FEED” position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Add an auto power table feed to your milling machine! A simple and inexpensive way to increase productivity! Small volume and easy installation. Excellent speed control in the entire range. Jog function operates at any feed speed. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. 1 x APF-260 Power Feed. 1 x X-Axis Fix Stand with Bushing. 1 x Bevel Gear with Fix Ring. 1 x Handle Washer. 2 x Stop Blocks. 2 x Stop Set. 2 x Socket Screws (M8P1.2535). 2 x Socket Screws (M8P1.025). 6 x Small Shims (f26.2f16.20.25t). 2 x Small Shims (f26.2f16.20.1t). 3 x Small Shims (f26.2f16.21.0t). 4 x Large Shims (f43.4f33.40.25t). 2 x Spring Pins. 1 x Cable Clamp. 1 x User Manual. We promise that every item has been sent. But sometimes there is also 0.3% package lost during transport. Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, Please tell us the problem in details and Please con-tact us within 14 days after you receive the package. We will provide you the best solution for any problem with the item. Due to time zones, our reply to your questions may not be immediately. But within above working time, we will reply you-= within 24 hours. If it’s non-workdays, please kindly be patient and wait till Monday. Please feel free to con-tact us if you have any questions.

220V 100W PROXXON mini milling machine MF70 bench driller. Base of grey cast iron. Including both vertical column and compound table of treated, quality aluminium. All axes are play-free and have adjustable gibs. Headstock of die-cast aluminium contains the 24 pole special (balanced) motor is super stable even at high operating speeds. This stability facilitates the use of the finest cutters. The triple slit, hardened steel MICROMOT collets cover 1.0 – 1.5 – 2.0 – 2.35 – 3.0 – 3.2mm. The table is fitted with 3 T-slots of the 12 x 6 x 5mm MICROMOT norm. An adjustable ruler scale eases the positioning of the workpiece. All handwheels are zero adjustable with 1 revolution = 1.0mm, 1 division = 0.05mm. Technical data: 220 – 240V, 100W, 50/60Hz. Spindle speeds 5,000 – 20,000rpm. Table 200 x 70mm with X-Y travel of 134 and 46mm respectively, with vertical travel 80mm. Footprint size 130 x 225mm and overall height 370mm. The clamping blocks depicted are included too, but not the workpiece! Technical Data: Power consumption: 220 – 240 V 50/60 Hz W. Speed: 5000 to 20000 g / min Table size: 200 70 mm X Stroke: 134mm Running Y: 46mm Base height: 370 mm grossWeight: 10 kg equipment Collets 1.0 to 3.2mm in diameter; Work plan with 3 T-slots (under Micromot 12 6 5 mm). The item “220V 100W PROXXON mini milling machine MF70 bench driller” is in sale since Tuesday, November 24, 2015. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “giron-ricar” and is located in San Salvador, San Salvador. This item can be shipped worldwide.