THIS LISTING COMES WITH A STAND. IF YOU ARE LOOKING FOR A MILL WITH NO STAND, PLEASE SEE OUR OTHER LISTING. Extremely Reliable, Brushless DC Variable Speed Motor Included Standard. Belt Drive Design, For Smoother, Quieter Running. Extra Large Column To Base Mount. 3 Bolt Head to Column Mount is Standard, Also For Increased Rigidity. Larger Dials at Table Ends, Graduated in. 001, For Easier Reading, And More Accurate Table Movements. Leadscrews Are True Inch Pitch Screws (Not Metric Conversions Like Many), 10 Threads Per Inch. More Information below It is NOT just the same old model with just a belt drive upgrade Be sure to compare carefully. Special Features that set this mill apart from others (BE SURE TO COMPARE THESE DIFFERENCES). MUCH Larger Travels and work area. Quill DRO Included Standard (This is for the spindle up/down movement). 3 Bolt Head Mount is now standard (where the head mounts to the Z Axis), for more rigidity when milling Much improved over the single bolt mount type. Main Z Axis Column is attached to the base with 4 bolts, and mounted from the top, with a wide, proper mounting surface for much more rigidity over other models in this size range. 001 Readings with larger dials on the X and Y axis, with true 10 Thread Per Inch Leadscrews make it easier to cut accurately One line on the dial is. 001, one full turn of the handwheel is. 100, much easier to use than those with odd metric conversions. 50-3000 RPM variable speed with the turn of a knob, properly set up with Low and High for a wider speed range, and plenty of power at lower speeds. Precision ground ways for smoother movements Not just rough milled. Thrust Bearings in leadscrew ends not bushings Much smoother movements and less backlash. Split nuts on X and Y Axis to allow for backlash adjustment. DC BRUSHLESS MOTOR, Variable Speed, POWERFUL, SMOOTH, and RELIABLE Belt Drive from Motor to Spindle runs MUCH quieter than others, and eliminates any failure prone plastic gears (And the hassle of changing them when stripped). Variable Speed with Belt Drive and Brushless DC Motor 4. Way Cover Set 5. R8 Spindle Taper 7. Quill/Spindle Depth DRO 8. PM30MV (DC Brushless Motor, and Belt Drive Head is Standard) Max. Drilling Capacity 1-1/4 Max. End Milling Capacity 3/4 Max. Face Milling Capacity 3-1/2 Table Size 8-1/4 x 33 Cross Travel (Y Axis) 8-3/4 Longitudinal Travel (X Axis) 23 Table Leadscrew Pitch 10 TPI. 100 Per Turn Table Dial Graduations. 001 Vertical Travel (Z Axis) 14 Max Distance Spindle to Table 17 Taper of Spindle R-8, w/7/16-20 Drawbar Thread Spindle Travel 3 T Slot Size Actual size 14mm, our 9/16 kit listed is sized for this machine Range of Spindle Speeds 50-3000 rpm, 2 Ranges (Properly set up with high and low range belt positions for more power at lower speeds as it should be) Headstock Tilt Left & Right ±90° Motor 2 HP Net Weight (Without Stand) 530 LBS: 605 LBS (With Stand) Power Required 220V, Single Phase, 10 Amp. Dimensions Height, Head at normal working height 67 (With Stand) Max Height, Head at top of travel 67. Width, Tip to Tip of table handles 46-1/4 Dimension Front To Back, from back of chip pan, to front table handle tip 31 (Can be pushed back against a wall, and table handle tip will be 31 from wall). Average time delivered is 2-7 days depending on how far from Pittsburgh you are, it could be a little longer in remote places but normally is very fast. 1060 Montour West Industrial Park. If you have ANY questions, feel free to message us. Check out our other auctions for more lathes and mills. The item “PM-30MV VERTICAL BENCH TYPE MILLING MACHINE with3-AXIS DRO AND STAND FREE SHIPPING” is in sale since Tuesday, September 17, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “qualitymachinetools” and is located in Pittsburgh, Pennsylvania. This item can be shipped to United States, Canada.

• MPN: PM-30MV w/DRO AND STAND
• Brand: Precision Matthews
• Country//Region of Manufacture: China

Now to the listing. VARIABLE SPEED Vertical Bench Type Milling Machine with chip tray, as shown. This machine uses 120V Standard Power! Main Features Of This Machine. Completely different factory, castings, and design than many others out there, GREATLY improved design. Extremely Reliable, Brushless DC Variable Speed Motor Included Standard. Belt Drive Design, For Smoother, Quieter Running. Extra Large Column To Base Mount, Over 400% More Area, Makes A Much More Rigid Machine, Greatly Improved Over Other Machines In This Size Range. 3 Bolt Head to Column Mount is Standard, Also For Increased Rigidity. Runs in both Forward and Reverse, Good for Tapping. Larger Dials at Table Ends, Graduated in. 001, For Easier to Read, Accurate Table Movements. Leadscrews Are True Inch Pitch Screws (Not Metric Conversions Like Many), 10 Threads Per Inch. More Information below under the DESCRIPTION Tab below It is NOT just the same old model with just a belt drive upgrade Be sure to compare carefully. Special Features that set this mill apart from others (BE SURE TO COMPARE THESE DIFFERENCES). Quill DRO Included Standard (This is for the spindle up/down movement). 3 Bolt Head Mount is now standard (where the head mounts to the Z Axis), for more rigidity when milling Much improved over the single bolt mount type. Main Z Axis Column is attached to the base with 4 bolts, and mounted from the top, with a wide, proper mounting surface for much more rigidity over other models in this size range. 001 Readings with larger dials on the X and Y axis, with true 10 Thread Per Inch Leadscrews make it easier to cut accurately One line on the dial is. 001, one full turn of the handwheel is. 100, much easier to use than those with odd metric conversions. Precision ground ways for smoother movements Not just rough milled. Thrust Bearings in leadscrew ends not bushings Much smoother movements and less backlash. Split nuts on X and Y Axis to allow for backlash adjustment. DC BRUSHLESS MOTOR, Variable Speed, POWERFUL, SMOOTH, and RELIABLE Belt Drive from Motor to Spindle runs MUCH quieter than others, and eliminates any failure prone plastic gears (And the hassle of changing them when stripped). Average time delivered is 2-7 days depending on how far from Pittsburgh you are, it could be a little longer in remote places but normally is very fast. 1060 Montour West Industrial Park. We are machinists here too, so we know what we sell. This is really a top quality machine, and will last a long, long time. AND we are here for support too. We sell these machines regularly, we know them inside and out, and have been in business for many years, so if there is any question, we can help. Variable Speed with Belt Drive and Brushless DC Motor. PM25MV (DC Brushless Motor, and Belt Drive Head is Standard). End Milling Capacity 3/4. Face Milling Capacity 2/1/2. Table Size 27-1/2 x 7-1/8. Cross Travel (Y Axis) 7. Longitudinal Travel (X Axis) 19. Table Leadscrew Pitch 10 TPI. Vertical Travel (Z Axis) 13. Max Distance Spindle to Table 13. Taper of Spindle R-8, w/7/16-20 Drawbar Thread. T Slot Size Actual size 12mm, our 1/2 kit listed is sized for this machine. Range of Spindle Speeds 50-2250rpm, 2 Steps. Headstock Tilt Left & Right ±90°. Machine Height (Without Stand) 38-1/2. Net Weight (Not Including Stand) 265 LBS. Net Weight (With Stand) 350 LBS. Power Required 110/120V, Minimum 15 Amp Circuit (Do Not Use Extension Cords). NO extra charge for residential or anything on these, as long as a truck can get to you, its covered. Check out our other auctions for more lathes and mills. The item “PM-25MV BENCH TOP MILLING MACHINE with3-AXIS DRO STAND VARIABLE SPEED SHIPS FREE” is in sale since Friday, February 15, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “qualitymachinetools” and is located in Pittsburgh, Pennsylvania. This item can be shipped to United States, Canada.

• MPN: PM-25MV
• Brand: Precision Matthews
• Country//Region of Manufacture: China

Now to the listing. VARIABLE SPEED Vertical Bench Type Milling Machine with chip tray, as shown. This machine uses 120V Standard Power! Main Features Of This Machine. Completely different factory, castings, and design than many others out there, GREATLY improved design. Extremely Reliable, Brushless DC Variable Speed Motor Included Standard. Belt Drive Design, For Smoother, Quieter Running. Extra Large Column To Base Mount, Over 400% More Area, Makes A Much More Rigid Machine, Greatly Improved Over Other Machines In This Size Range. 3 Bolt Head to Column Mount is Standard, Also For Increased Rigidity. Runs in both Forward and Reverse, Good for Tapping. Larger Dials at Table Ends, Graduated in. 001, For Easier to Read, Accurate Table Movements. Leadscrews Are True Inch Pitch Screws (Not Metric Conversions Like Many), 10 Threads Per Inch. More Information below under the DESCRIPTION Tab below It is NOT just the same old model with just a belt drive upgrade Be sure to compare carefully. Special Features that set this mill apart from others (BE SURE TO COMPARE THESE DIFFERENCES). Quill DRO Included Standard (This is for the spindle up/down movement). 3 Bolt Head Mount is now standard (where the head mounts to the Z Axis), for more rigidity when milling Much improved over the single bolt mount type. Main Z Axis Column is attached to the base with 4 bolts, and mounted from the top, with a wide, proper mounting surface for much more rigidity over other models in this size range. 001 Readings with larger dials on the X and Y axis, with true 10 Thread Per Inch Leadscrews make it easier to cut accurately One line on the dial is. 001, one full turn of the handwheel is. 100, much easier to use than those with odd metric conversions. Precision ground ways for smoother movements Not just rough milled. Thrust Bearings in leadscrew ends not bushings Much smoother movements and less backlash. Split nuts on X and Y Axis to allow for backlash adjustment. DC BRUSHLESS MOTOR, Variable Speed, POWERFUL, SMOOTH, and RELIABLE Belt Drive from Motor to Spindle runs MUCH quieter than others, and eliminates any failure prone plastic gears (And the hassle of changing them when stripped). Average time delivered is 2-7 days depending on how far from Pittsburgh you are, it could be a little longer in remote places but normally is very fast. Quality Machine Tools, 701 Parkway View Drive, Pittsburgh, PA 15205. We are machinists here too, so we know what we sell. This is really a top quality machine, and will last a long, long time. AND we are here for support too. We sell these machines regularly, we know them inside and out, and have been in business for many years, so if there is any question, we can help. Variable Speed with Belt Drive and Brushless DC Motor. PM25MV (DC Brushless Motor, and Belt Drive Head is Standard). End Milling Capacity 3/4. Face Milling Capacity 2/1/2. Table Size 27-1/2 x 7-1/8. Cross Travel (Y Axis) 7. Longitudinal Travel (X Axis) 19. Table Leadscrew Pitch 10 TPI. Vertical Travel (Z Axis) 13. Max Distance Spindle to Table 13. Taper of Spindle R-8, w/7/16-20 Drawbar Thread. T Slot Size Actual size 12mm, our 1/2 kit listed is sized for this machine. Range of Spindle Speeds 50-2250rpm, 2 Steps. Headstock Tilt Left & Right ±90°. Machine Height (Without Stand) 38-1/2. Net Weight (Not Including Stand) 265 LBS. Net Weight (With Stand) 350 LBS. Power Required 110/120V, Minimum 15 Amp Circuit (Do Not Use Extension Cords). NO extra charge for residential or anything on these, as long as a truck can get to you, its covered. Check out our other auctions for more lathes and mills. The item “PM-25MV BENCH TOP MILLING MACHINE with3-AXIS DRO STAND VARIABLE SPEED SHIPS FREE” is in sale since Tuesday, November 13, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “qualitymachinetools” and is located in Pittsburgh, Pennsylvania. This item can be shipped to United States, Canada.

• MPN: PM-25MV
• Brand: Precision Matthews
• Country//Region of Manufacture: China

NO STAND INCLUDED IN THIS LISTING. Now to the listing. VARIABLE SPEED Vertical Bench Type Milling Machine with chip tray, as shown. This machine uses 120V Standard Power! Main Features Of This Machine. Completely different factory, castings, and design than many others out there, GREATLY improved design. Extremely Reliable, Brushless DC Variable Speed Motor Included Standard. Belt Drive Design, For Smoother, Quieter Running. Extra Large Column To Base Mount, Over 400% More Area, Makes A Much More Rigid Machine, Greatly Improved Over Other Machines In This Size Range. 3 Bolt Head to Column Mount is Standard, Also For Increased Rigidity. Runs in both Forward and Reverse, Good for Tapping. Larger Dials at Table Ends, Graduated in. 001, For Easier to Read, Accurate Table Movements. Leadscrews Are True Inch Pitch Screws (Not Metric Conversions Like Many), 10 Threads Per Inch. More Information below under the DESCRIPTION Tab below It is NOT just the same old model with just a belt drive upgrade Be sure to compare carefully. Special Features that set this mill apart from others (BE SURE TO COMPARE THESE DIFFERENCES). Quill DRO Included Standard (This is for the spindle up/down movement). 3 Bolt Head Mount is now standard (where the head mounts to the Z Axis), for more rigidity when milling Much improved over the single bolt mount type. Main Z Axis Column is attached to the base with 4 bolts, and mounted from the top, with a wide, proper mounting surface for much more rigidity over other models in this size range. 001 Readings with larger dials on the X and Y axis, with true 10 Thread Per Inch Leadscrews make it easier to cut accurately One line on the dial is. 001, one full turn of the handwheel is. 100, much easier to use than those with odd metric conversions. Precision ground ways for smoother movements Not just rough milled. Thrust Bearings in leadscrew ends not bushings Much smoother movements and less backlash. Split nuts on X and Y Axis to allow for backlash adjustment. DC BRUSHLESS MOTOR, Variable Speed, POWERFUL, SMOOTH, and RELIABLE Belt Drive from Motor to Spindle runs MUCH quieter than others, and eliminates any failure prone plastic gears (And the hassle of changing them when stripped). Average time delivered is 2-7 days depending on how far from Pittsburgh you are, it could be a little longer in remote places but normally is very fast. Quality Machine Tools, 701 Parkway View Drive, Pittsburgh, PA 15205. We are machinists here too, so we know what we sell. This is really a top quality machine, and will last a long, long time. AND we are here for support too. We sell these machines regularly, we know them inside and out, and have been in business for many years, so if there is any question, we can help. Variable Speed with Belt Drive and Brushless DC Motor. PM25MV (DC Brushless Motor, and Belt Drive Head is Standard). End Milling Capacity 3/4. Face Milling Capacity 2/1/2. Table Size 27-1/2 x 7-1/8. Cross Travel (Y Axis) 7. Longitudinal Travel (X Axis) 19. Table Leadscrew Pitch 10 TPI. Vertical Travel (Z Axis) 13. Max Distance Spindle to Table 13. Taper of Spindle R-8, w/7/16-20 Drawbar Thread. T Slot Size Actual size 12mm, our 1/2 kit listed is sized for this machine. Range of Spindle Speeds 50-2250rpm, 2 Steps. Headstock Tilt Left & Right ±90°. Machine Height (Without Stand) 38-1/2. Net Weight (Not Including Stand) 265 LBS. Power Required 110/120V, Minimum 15 Amp Circuit (Do Not Use Extension Cords). NO extra charge for residential or anything on these, as long as a truck can get to you, its covered. Check out our other auctions for more lathes and mills. The item “PM-25MV BENCH TOP MILLING MACHINE with3-AXIS DRO VARIABLE SPEED SHIPS FREE” is in sale since Tuesday, November 13, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “qualitymachinetools” and is located in Pittsburgh, Pennsylvania. This item can be shipped to United States, Canada.

• Country//Region of Manufacture: China
• Modified Item: No
• Custom Bundle: No
• MPN: PM-25MV
• Brand: Precision Matthews
• Non-Domestic Product: No

NO STAND INCLUDED IN THIS LISTING. Now to the listing. VARIABLE SPEED Vertical Bench Type Milling Machine with chip tray, as shown. This machine uses 120V Standard Power! Main Features Of This Machine. Completely different factory, castings, and design than many others out there, GREATLY improved design. Extremely Reliable, Brushless DC Variable Speed Motor Included Standard. Belt Drive Design, For Smoother, Quieter Running. Extra Large Column To Base Mount, Over 400% More Area, Makes A Much More Rigid Machine, Greatly Improved Over Other Machines In This Size Range. 3 Bolt Head to Column Mount is Standard, Also For Increased Rigidity. Runs in both Forward and Reverse, Good for Tapping. Larger Dials at Table Ends, Graduated in. 001, For Easier to Read, Accurate Table Movements. Leadscrews Are True Inch Pitch Screws (Not Metric Conversions Like Many), 10 Threads Per Inch. More Information below under the DESCRIPTION Tab below It is NOT just the same old model with just a belt drive upgrade Be sure to compare carefully. Special Features that set this mill apart from others (BE SURE TO COMPARE THESE DIFFERENCES). Quill DRO Included Standard (This is for the spindle up/down movement). 3 Bolt Head Mount is now standard (where the head mounts to the Z Axis), for more rigidity when milling Much improved over the single bolt mount type. Main Z Axis Column is attached to the base with 4 bolts, and mounted from the top, with a wide, proper mounting surface for much more rigidity over other models in this size range. 001 Readings with larger dials on the X and Y axis, with true 10 Thread Per Inch Leadscrews make it easier to cut accurately One line on the dial is. 001, one full turn of the handwheel is. 100, much easier to use than those with odd metric conversions. Precision ground ways for smoother movements Not just rough milled. Thrust Bearings in leadscrew ends not bushings Much smoother movements and less backlash. Split nuts on X and Y Axis to allow for backlash adjustment. DC BRUSHLESS MOTOR, Variable Speed, POWERFUL, SMOOTH, and RELIABLE Belt Drive from Motor to Spindle runs MUCH quieter than others, and eliminates any failure prone plastic gears (And the hassle of changing them when stripped). Average time delivered is 2-7 days depending on how far from Pittsburgh you are, it could be a little longer in remote places but normally is very fast. Quality Machine Tools, 701 Parkway View Drive, Pittsburgh, PA 15205. We are machinists here too, so we know what we sell. This is really a top quality machine, and will last a long, long time. AND we are here for support too. We sell these machines regularly, we know them inside and out, and have been in business for many years, so if there is any question, we can help. Variable Speed with Belt Drive and Brushless DC Motor. PM25MV (DC Brushless Motor, and Belt Drive Head is Standard). End Milling Capacity 3/4. Face Milling Capacity 2/1/2. Table Size 27-1/2 x 7-1/8. Cross Travel (Y Axis) 7. Longitudinal Travel (X Axis) 19. Table Leadscrew Pitch 10 TPI. Vertical Travel (Z Axis) 13. Max Distance Spindle to Table 13. Taper of Spindle R-8, w/7/16-20 Drawbar Thread. T Slot Size Actual size 12mm, our 1/2 kit listed is sized for this machine. Range of Spindle Speeds 50-2250rpm, 2 Steps. Headstock Tilt Left & Right ±90°. Machine Height (Without Stand) 38-1/2. Net Weight (Not Including Stand) 265 LBS. Power Required 110/120V, Minimum 15 Amp Circuit (Do Not Use Extension Cords). NO extra charge for residential or anything on these, as long as a truck can get to you, its covered. Check out our other auctions for more lathes and mills. The item “PM-25MV BENCH TOP MILLING MACHINE with3-AXIS DRO VARIABLE SPEED SHIPS FREE” is in sale since Friday, August 17, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “qualitymachinetools” and is located in Pittsburgh, Pennsylvania. This item can be shipped to United States, Canada.

• Country//Region of Manufacture: China
• Modified Item: No
• Custom Bundle: No
• MPN: PM-25MV
• Brand: Precision Matthews
• Non-Domestic Product: No

WITH 3-AXIS DRO INSTALLED! VARIABLE SPEED Vertical Bench Type Milling Machine with chip tray, as shown. This machine uses 120V Standard Power! Main Features Of This Machine. Completely different factory, castings, and design than many others out there, GREATLY improved design. Extremely Reliable, Brushless DC Variable Speed Motor Included Standard. Belt Drive Design, For Smoother, Quieter Running. Extra Large Column To Base Mount, Over 400% More Area, Makes A Much More Rigid Machine, Greatly Improved Over Other Machines In This Size Range. 3 Bolt Head to Column Mount is Standard, Also For Increased Rigidity. Runs in both Forward and Reverse, Good for Tapping. Larger Dials at Table Ends, Graduated in. 001, For Easier to Read, Accurate Table Movements. Leadscrews Are True Inch Pitch Screws (Not Metric Conversions Like Many), 10 Threads Per Inch. More Information below under the DESCRIPTION Tab below It is NOT just the same old model with just a belt drive upgrade Be sure to compare carefully. Special Features that set this mill apart from others (BE SURE TO COMPARE THESE DIFFERENCES). Quill DRO Included Standard (This is for the spindle up/down movement). 3 Bolt Head Mount is now standard (where the head mounts to the Z Axis), for more rigidity when milling Much improved over the single bolt mount type. Main Z Axis Column is attached to the base with 4 bolts, and mounted from the top, with a wide, proper mounting surface for much more rigidity over other models in this size range. 001 Readings with larger dials on the X and Y axis, with true 10 Thread Per Inch Leadscrews make it easier to cut accurately One line on the dial is. 001, one full turn of the handwheel is. 100, much easier to use than those with odd metric conversions. Precision ground ways for smoother movements Not just rough milled. Thrust Bearings in leadscrew ends not bushings Much smoother movements and less backlash. Split nuts on X and Y Axis to allow for backlash adjustment. DC BRUSHLESS MOTOR, Variable Speed, POWERFUL, SMOOTH, and RELIABLE Belt Drive from Motor to Spindle runs MUCH quieter than others, and eliminates any failure prone plastic gears (And the hassle of changing them when stripped). 3-Axis Digital Readout Installed. Average time delivered is 2-7 days depending on how far from Pittsburgh you are, it could be a little longer in remote places but normally is very fast. Quality Machine Tools, 701 Parkway View Drive, Pittsburgh, PA 15205. We are machinists here too, so we know what we sell. This is really a top quality machine, and will last a long, long time. AND we are here for support too. We sell these machines regularly, we know them inside and out, and have been in business for many years, so if there is any question, we can help. Variable Speed with Belt Drive and Brushless DC Motor 4. Way Cover Set 5. R8 Spindle Taper 7. Quill/Spindle Depth DRO 8. PM25MV (DC Brushless Motor, and Belt Drive Head is Standard). End Milling Capacity 3/4. Face Milling Capacity 2/1/2. Table Size 27-1/2 x 7-1/8. Cross Travel (Y Axis) 7. Longitudinal Travel (X Axis) 19. Table Leadscrew Pitch 10 TPI. Vertical Travel (Z Axis) 13. Max Distance Spindle to Table 13. Taper of Spindle R-8, w/7/16-20 Drawbar Thread. T Slot Size Actual size 12mm, our 1/2 kit listed is sized for this machine. Range of Spindle Speeds 50-2250rpm, 2 Steps. Headstock Tilt Left & Right ±90°. Machine Height (Without Stand) 38-1/2. Net Weight (Not Including Base) 265 LBS. Power Required 110/120V, Minimum 15 Amp Circuit (Do Not Use Extension Cords). NO extra charge for residential or anything on these, as long as a truck can get to you, its covered. Check out our other auctions for more lathes and mills. The item “PM-25MV VERTICAL BENCH TOP MILLING MACHINE with3-AXIS DRO INSTALLED FREE SHIPPING” is in sale since Thursday, August 2, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “qualitymachinetools” and is located in Pittsburgh, Pennsylvania. This item can be shipped to United States, Canada.

• Modified Item: No
• Custom Bundle: No
• MPN: PM-25MV w/3ax DRO
• Brand: Precision Matthews
• Non-Domestic Product: No
• Country//Region of Manufacture: China

NO STAND INCLUDED IN THIS LISTING. Now to the listing. VARIABLE SPEED Vertical Bench Type Milling Machine with chip tray, as shown. This machine uses 120V Standard Power! Main Features Of This Machine. Completely different factory, castings, and design than many others out there, GREATLY improved design. Extremely Reliable, Brushless DC Variable Speed Motor Included Standard. Belt Drive Design, For Smoother, Quieter Running. Extra Large Column To Base Mount, Over 400% More Area, Makes A Much More Rigid Machine, Greatly Improved Over Other Machines In This Size Range. 3 Bolt Head to Column Mount is Standard, Also For Increased Rigidity. Runs in both Forward and Reverse, Good for Tapping. Larger Dials at Table Ends, Graduated in. 001, For Easier to Read, Accurate Table Movements. Leadscrews Are True Inch Pitch Screws (Not Metric Conversions Like Many), 10 Threads Per Inch. More Information below under the DESCRIPTION Tab below It is NOT just the same old model with just a belt drive upgrade Be sure to compare carefully. Special Features that set this mill apart from others (BE SURE TO COMPARE THESE DIFFERENCES). Quill DRO Included Standard (This is for the spindle up/down movement). 3 Bolt Head Mount is now standard (where the head mounts to the Z Axis), for more rigidity when milling Much improved over the single bolt mount type. Main Z Axis Column is attached to the base with 4 bolts, and mounted from the top, with a wide, proper mounting surface for much more rigidity over other models in this size range. 001 Readings with larger dials on the X and Y axis, with true 10 Thread Per Inch Leadscrews make it easier to cut accurately One line on the dial is. 001, one full turn of the handwheel is. 100, much easier to use than those with odd metric conversions. Precision ground ways for smoother movements Not just rough milled. Thrust Bearings in leadscrew ends not bushings Much smoother movements and less backlash. Split nuts on X and Y Axis to allow for backlash adjustment. DC BRUSHLESS MOTOR, Variable Speed, POWERFUL, SMOOTH, and RELIABLE Belt Drive from Motor to Spindle runs MUCH quieter than others, and eliminates any failure prone plastic gears (And the hassle of changing them when stripped). Average time delivered is 2-7 days depending on how far from Pittsburgh you are, it could be a little longer in remote places but normally is very fast. Quality Machine Tools, 701 Parkway View Drive, Pittsburgh, PA 15205. We are machinists here too, so we know what we sell. This is really a top quality machine, and will last a long, long time. AND we are here for support too. We sell these machines regularly, we know them inside and out, and have been in business for many years, so if there is any question, we can help. Variable Speed with Belt Drive and Brushless DC Motor. PM25MV (DC Brushless Motor, and Belt Drive Head is Standard). End Milling Capacity 3/4. Face Milling Capacity 2/1/2. Table Size 27-1/2 x 7-1/8. Cross Travel (Y Axis) 7. Longitudinal Travel (X Axis) 19. Table Leadscrew Pitch 10 TPI. Vertical Travel (Z Axis) 13. Max Distance Spindle to Table 13. Taper of Spindle R-8, w/7/16-20 Drawbar Thread. T Slot Size Actual size 12mm, our 1/2 kit listed is sized for this machine. Range of Spindle Speeds 50-2250rpm, 2 Steps. Headstock Tilt Left & Right ±90°. Machine Height (Without Stand) 38-1/2. Net Weight (Not Including Stand) 265 LBS. Power Required 110/120V, Minimum 15 Amp Circuit (Do Not Use Extension Cords). NO extra charge for residential or anything on these, as long as a truck can get to you, its covered. Check out our other auctions for more lathes and mills. The item “PM-25MV BENCH TOP MILLING MACHINE with3-AXIS DRO VARIABLE SPEED SHIPS FREE” is in sale since Wednesday, July 18, 2018. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “qualitymachinetools” and is located in Pittsburgh, Pennsylvania. This item can be shipped to United States, Canada.

• MPN: PM-25MV
• Brand: Precision Matthews
• Country//Region of Manufacture: China

NO STAND INCLUDED IN THIS LISTING. Now to the listing. VARIABLE SPEED Vertical Bench Type Milling Machine with chip tray, as shown. This machine uses 120V Standard Power! Main Features Of This Machine. Completely different factory, castings, and design than many others out there, GREATLY improved design. Extremely Reliable, Brushless DC Variable Speed Motor Included Standard. Belt Drive Design, For Smoother, Quieter Running. Extra Large Column To Base Mount, Over 400% More Area, Makes A Much More Rigid Machine, Greatly Improved Over Other Machines In This Size Range. 3 Bolt Head to Column Mount is Standard, Also For Increased Rigidity. Runs in both Forward and Reverse, Good for Tapping. Larger Dials at Table Ends, Graduated in. 001, For Easier to Read, Accurate Table Movements. Leadscrews Are True Inch Pitch Screws (Not Metric Conversions Like Many), 10 Threads Per Inch. More Information below under the DESCRIPTION Tab below It is NOT just the same old model with just a belt drive upgrade Be sure to compare carefully. Special Features that set this mill apart from others (BE SURE TO COMPARE THESE DIFFERENCES). Quill DRO Included Standard (This is for the spindle up/down movement). 3 Bolt Head Mount is now standard (where the head mounts to the Z Axis), for more rigidity when milling Much improved over the single bolt mount type. Main Z Axis Column is attached to the base with 4 bolts, and mounted from the top, with a wide, proper mounting surface for much more rigidity over other models in this size range. 001 Readings with larger dials on the X and Y axis, with true 10 Thread Per Inch Leadscrews make it easier to cut accurately One line on the dial is. 001, one full turn of the handwheel is. 100, much easier to use than those with odd metric conversions. Precision ground ways for smoother movements Not just rough milled. Thrust Bearings in leadscrew ends not bushings Much smoother movements and less backlash. Split nuts on X and Y Axis to allow for backlash adjustment. DC BRUSHLESS MOTOR, Variable Speed, POWERFUL, SMOOTH, and RELIABLE Belt Drive from Motor to Spindle runs MUCH quieter than others, and eliminates any failure prone plastic gears (And the hassle of changing them when stripped). Average time delivered is 2-7 days depending on how far from Pittsburgh you are, it could be a little longer in remote places but normally is very fast. Quality Machine Tools, 701 Parkway View Drive, Pittsburgh, PA 15205. We are machinists here too, so we know what we sell. This is really a top quality machine, and will last a long, long time. AND we are here for support too. We sell these machines regularly, we know them inside and out, and have been in business for many years, so if there is any question, we can help. Variable Speed with Belt Drive and Brushless DC Motor. PM25MV (DC Brushless Motor, and Belt Drive Head is Standard). End Milling Capacity 3/4. Face Milling Capacity 2/1/2. Table Size 27-1/2 x 7-1/8. Cross Travel (Y Axis) 7. Longitudinal Travel (X Axis) 19. Table Leadscrew Pitch 10 TPI. Vertical Travel (Z Axis) 13. Max Distance Spindle to Table 13. Taper of Spindle R-8, w/7/16-20 Drawbar Thread. T Slot Size Actual size 12mm, our 1/2 kit listed is sized for this machine. Range of Spindle Speeds 50-2250rpm, 2 Steps. Headstock Tilt Left & Right ±90°. Machine Height (Without Stand) 38-1/2. Net Weight (Not Including Stand) 265 LBS. Power Required 110/120V, Minimum 15 Amp Circuit (Do Not Use Extension Cords). NO extra charge for residential or anything on these, as long as a truck can get to you, its covered. Check out our other auctions for more lathes and mills. The item “PM-25MV BENCH TOP MILLING MACHINE with3-AXIS DRO VARIABLE SPEED SHIPS FREE” is in sale since Thursday, June 14, 2018. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “qualitymachinetools” and is located in Pittsburgh, Pennsylvania. This item can be shipped to United States, Canada.

• MPN: PM-25MV
• Brand: Precision Matthews
• Country//Region of Manufacture: China