Follow these steps (see pic in last photo for details). 9 Timesavers #948 Belt Sander.

Follow these steps (see pic in last photo for details). Bridgeport #Series I Vertical Mill w/ DRO.

Follow these steps (see pic in last photo for details). Lagun #FTV-2 Vertical Knee Mill.

1998 HAAS VF-2 vertical machining center (vices & tooling not included). Check out youtube link to see full machine. Table size 36″ x 14″. Max weight on table 1,500 lbs. X axis travel 30. Y axis travel 16. Z axis travel 20. Rapid traverse rates 833 ipm. Cutting feed rates 720 ipm. Spindle nose to table (min-max) 4″-24″. Taper size cat 40. Spindle range 7,500 rpm. Spindle power 20 HP. Automatic tool changer, capacity 20. Equipped with 4 th axis drive and wiring. Automatic chip auger and programmable coolant nozzle. Coolant tank and pump.

Very nice condition and includes table driven dividing head worth over 1200 alone. 12/30/2022 is last date to remove. Machine weight apprx 9000# Local forklift rentals are apprx 500.00 for a 10k lift. I have a 4000# lift truck on site but wont budge this. Balance within 7 days. Able size 315 x 1250 mmm. Tool size SK50, speed range (1/min) 28-1400. Travel (X/Y/Z) 850/270/505 mm. Feed range (mm/min) X, Y 16-800, Z 5-250. Total power consumtion 8 kW. Milling head tilteable +/- 45°, travel of pinion 90 mm. Rapid feed in 3 axis. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “rodbuilderswarehouse” and is located in this country: US. This item can be shipped to United States.

• Brand: Heckert
• Machine Type: Milling Machine
• Model: FU 315 2/PS
• Make: HECKERT
• MPN: FU 315 2/PS

ACER “e” Series Bed Mill, 14″ x 54″ – e-1454B. Standard Accessories for the e-1454B Bed Mill. Tool box with tools. CAT or BT #40 drawbar (NST optional). Operation manual with parts manual. Leveling pads & screws. 5 HP inverter motor with fan cooling system that dissipates heat efficiency. Extra oilers to lubricate the high-low moving device and to oil the quill. One piece quill pinion & shaft. Precision hardened & ground slideways. Precision ground C5 ball screws. Precision ground guide line to 0.0002. Turcite-B coated saddle ways. Grease fitting for lubricating bull gear. CNC & operator console. Hand scraped saddle ways. X, Y and knee axes are hardened and ground to HRC 52 degrees. Drives & accessories cabinet. Hardened & ground table top to HRC 52 degrees. 230V / 460V three phase ready and available to run at single phase 230V when specified. We are liquidating a machine shop with tons of great tooling. So far we have only listed a fraction of the items for sale. We still have to go thru several warehouses as well. The property has 100′s of chucks, tables, spacers, indexers and carts and carts of tooling. Racks and Racks of Cat 50, cat 40, cat 30 and many others. Racks and Racks of face mills (sorry no carbide) and other tooling. You can expect we have most everything that goes into a typical machine shop. Over the next couple of weeks we will be listing tons of new chucks. If you are looking for a particular size let us know and we probably have it and can make a deal and will design a special ad for you. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “howfactor” and is located in this country: US. This item can be shipped to United States.

• Model: Acer E-1454B CNC
• Function: Milling
• Brand: Acer
• Control: CNC

Cnc fanuc spindle motor. This motor was in a Supermax but will fit most mills that are fanuc. The motor has never had issues it has mounting plates and has nice smooth bearings in it very quite. New bearings put in in 2014. Have many other parts I’ll be listing also a few machines to come. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “fastmini27″ and is located in this country: US. This item can be shipped to United States.

• Spindle Horsepower: 30 hp
• Machine Type: Machining Center
• Power Source: Electric
• Custom Bundle: No
• Table Length: 40 in – 59.9 in
• Spindle Taper: CAT 40
• Modified Item: No
• Brand: FANUC
• Function: Drilling, Milling
• X-Axis Travel Bed: 41 in – 60 in
• Control: CNC
• Model Year: 1994
• Max Spindle Speed (RPM): 7501 – 10000
• Voltage: 440 V
• Model: 60 A
• Y-Axis Travel Bed: 36 in – 40 in
• Country/Region of Manufacture: Japan

CNC mill, VMC Romi D400 Mini Mill, FANUC, MUST SELL MAKE AN OFFER!!! This is a Romi D400 12X16 minimill. It is one of several machining centers in our shop, the others get the majority of the work, so this little guy only gets used for the occasional little job and making fixtures. It had about 400 hours on it when we bought it new from the dealer because they were cutting air in their showroom. Those hours were zeroed out when we got it. I put another 2600 hours on it for a total of about 3,000 total running hours. It still jogs back and forth cleanly in. 0001 (tenths) and the ways and screws still sound like it did when it was new. It’s barely broken in. We bought this machine for a specific aluminum job but it does okay in most anything. We’ve cut steel, aluminum and plastics including acrylic and phenolic but we’ve never cut abrasive materials like G10, carbon fiber or cast iron on this machine. We have always fed it clean, dry, filtered air. This is a small machine, it is 6 feet wide and 7 feet deep and 7 feet tall with the head down. You could probably just squeeze it under a 7′ garage door if you remove the door trim. It is 220V three phase but it will run fine on a good rotary phase converter. I bought this mill instead of a Haas Minimill because it has 14″ Z travel rather than 10″ so it doesn’t stuff long tools like drills into your work during a tool change and it also has 14 tools rather than 10, and a 7,500 RPM spindle rather than 6,000. Also, it weighs around 6,000 pounds, almost twice as much as the little Haas, which gives it more grunt behind the cut, which helps your surface finish, material removal rates and tool life. The only things I don’t like about this mill is the spindle and servos are belt driven with cogged belts, like a Haas, which seem loud in a shop full of direct drive Mori, and it has a little coolant leak out the back which we put a little pan under and dump once or twice a month. The Fanuc OMi Mate control is bullet proof and has never malfunctioned. It has about 256K memory in the control and it also has a PCMCIA slot for running programs of practically unlimited size. It is full three axis linear interpolation with circular and helical interpolation. You can rigid tap (the spindle has an encoder on it) and thread mill with it. However I need to get this off my floor as soon as possible because we have a “new” machine that arrives in about 10 days and I need this out of here ASAP. So, I will consider all offers and accept the best offer in this time frame. We can load here for free on your truck. Also, if you’re local I can help you unload it and skate it into place. Includes all manuals and an old Kurt vise. We also have a ton of tool holders in excellent condition that fit this machine we could sell cheap in a side deal. The item “LOW HOUR CNC mill, VMC Romi D400 Mini Mill, FANUC, MUST SELL MAKE AN OFFER” is in sale since Thursday, October 29, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “aim_industrial” and is located in Mooresville, North Carolina. This item can’t be shipped, the buyer must pick up the item.

• Brand: Romi
• Function: Milling
• Control: Fanuc
• Model Year: 2004
• X-Axis Travel Bed: 16 in – 20 in
• Model: D400
• Max Spindle Speed (RPM): 7500
• Power Source: Electric
• Machine Type: Machining Center
• Voltage: 220 V
• Y-Axis Travel Bed: 10 in – 15 in
• Spindle Taper: BT40
• Spindle Horsepower: 5 – 7.5

The machine was working until the tape machine was removed. This iron is sound, but the machine needs a retrofit. Comes with tool holders in photos, I believe these are all 30 taper. The item “Bridgeport Textron Vertical Milling Machine MUST SELL ASAP” is in sale since Thursday, September 19, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “jadod_8820″ and is located in Reno, Nevada. This item can’t be shipped, the buyer must pick up the item.

• Machine Type: Vertical Milling Machine
• MPN: Does Not Apply
• Brand: Bridgeport
• Control: CNC

This listing is for a. Mazak Variaxis 5 Axis Machining Center, New 2005. It has not run in several years but appears to be complete! Inspection is HIGHLY ENCOURAGED! Specs we got ONLINE, please verify independently. 120 + 30 degrees. The machine is currently in storage! Please check out our Feedback, we are straight shooters! The item “MUST SELL NO RESERVE 2005 Mazak 5 Axis Variaxis Machining Center #630-5X” is in sale since Thursday, November 3, 2016. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “machinre_nuteksalesparts” and is located in Grand Rapids, Michigan. This item can be shipped to United States.