American Business ALL ITEMS IN STOCK IN CALIFORNIA. American STANDARD PRODUCTS QUALITY GUARANTEED. AS-250 150Lbs Torque Power Feed Milling Machine X-Axis ALSGS 0-200RPM. WHY SHOP WITH FACTORY-SUPPLIES? Item was as described and arrived quickly. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. X-Axis Power Feed: The X-Axis power table feed is made of sturdy aluminum material. It is also designed with a handle, buttons, and knobs for simple operation. Revolution Speed: 0-200 RPM. High quality and efficiency to handle all your milling needs. Long Service Life: The power feed for the milling machine features a smooth and strengthened polished surface, which is waterproof, dustproof, and oilproof. That ensures a long service life in harsh working conditions. High Efficiency & Precision: The x-axis power feed is equipped with spiral bevel gears for rapid control. There are bearings to achieve high efficiency and precision as well. Low Noise & Easy Operation: The milling machine power feed features 9 levels of moving speeds, set by the rotary knob on the side. Moreover, it makes little noise when used, an essential piece of equipment for every workshop. Wide Compatibility: This milling table power feed fits multiple vertical knee-type mills with the same mounting pattern and a 5/8 diameter shaft on the end. Such as Bridgeport, Precision Matthews, Enco, Jet, Sharp, Acer, Webb, etc. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Before installation, be sure to turn off the power supply of the milling machine. Don’t install the power feed under live condition. The product is supplied by AC110V 50/60Hz Please? Prepare the required power supply for the product. If the product is used in a region not in conformity with the national power supply, please prepare a transformer, avoid using incorrect power supply and result in damage of the product. The product is provided with overload protection, the power supply will be cut out in case of overload or stuck. It can be reset automatically by restarting the power switch. Check whether spiral gear oil is enough when carrying out maintenance. Open the carbon brush cover semiannually to check whether the carbon brush is worn. If the length is less than 7mm, it is recommended to replace the two sets of carbon brushes at the same time. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). AS-250-150 X-Axis Power Feed for Milling Machine x 1. Set of Necessary Accessories x 1. Product Manual x 1. We offer detailed product descriptions and images to give you a real advantage in finding the products you’re looking for. All items are dispatched from our warehouse in HACIENDA HEIGHTS, CA. Some products may be dispatched in more than one carton. International Buyers – Please Note. If you have a problem with the product. We will require a picture of the damaged part for verification. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “super-homeonline” and is located in this country: US. This item can be shipped to United States.
- Rotate speed: 0-200 RPM
- Torque: 150 lbs
- Package size: 13\
- Gross weight: 6.5 kg(14.3 lb)
- Warranty: 5 Years
- UPC: 0895800908447
- EAN: 0895800908447
- Brand: VEVOR
- Function: Milling
- Control: Manual
- Machine Type: Milling Machine
- Power Source: Electric
- Max Spindle Speed (RPM): 200 RPM
- Voltage: 110 V
- Model: AS-250
- MPN: ZCXUN00525
