Custom Built Parker 404XR CNC Machine. GeckoDrive G201 Stepper Controller. X Travel = 400mm (415mm max). Y Travel = 300mm (310mm max). Z Travel = 100mm (120mm max). 16mm dia Precision Ground Ballscrew s. Proximity Sensors (Limit Switches). Includes all cables and is ready to Plug-N-Play. I have run a test program on this machine and. Posted a video to YouTube. THIS MACHINE HAS HIGH VOLTAGE COMPONENTS. THE CONTROLLER CASE WAS BUILT WITH ALUMINUM. FRAMING AND IS NOT’UL APPROVED’ AND IT IS. POSSIBLE THAT IT MAY NOT BE GROUNDED PROPERLY. IF YOU DO NOT HAVE THE EXPERIENCE TO WORK. WITH HIGH VOLTAGE ELECTRICAL EQUIPMENT. FROM THE IMPROPER USE OF THIS EQUIPMENT. THIS INCLUDES PROPERTY DAMAGE, BODILY INJURY OR LOSS OF LIFE. This is a custom Parker 404XR CNC machine that was built a. Few years ago but never put into service. It only has a few hours. Of run time for testing but it has never had a spindle attached to it. It was built using mostly new parts the three longer 404XR actuators. Were lightly used but are in excellent working condition. Complete turn-key system that includes computer with Mach3 installed. And is ready to plug-n-play. See YouTube video for demonstration. It is a 3-axis machine with with dual Parker 404XR actuators on. The’Y’ axis the’Y’ and’A’ axis are slaved together and the controller. Uses a 4-axis Mach3 breakout Board. The’Y’ and’X’ axis actuators. Have new Parker nema34 stepper motors and the’Z’ axis has a new. Pacific Scientific nema23 stepper motor. All of the Parker 404XR. Actuators have 16mm diameter precision ground ballscrews, and. All actuators also have proximity sensor (limit switches) that are. Wired to the breakout board to prevent overtravel. Uses a 4-axis SoundLogic breakout board and GeckoDrive G201. Stepper drivers with an Antek 39v 500watt unregulated power supply. The front of the controller has a’Power On’ and’Stop’ button that. Turn the machine on/off. The’Emergency Stop’ button on the controller. Will send a signal to the Mach3 breakout board to stop a program that. Is running and will stop the machine from moving but will not cut power. There is a digital voltage meter and amp meter the measures the output. Of the Antek power supply. The four’On / Off’ switches are used to disable. The G201 drives and cut power to the stepper motor so that you can. Manually adjust the axes if needed. The’Y&A Axis Lock / Unlock’ switch. Is used in conjunction with the’On/Off’ switches and when the Y and A. Axis are’locked’ you only need to turn off one of the switches (Y or A) and. It will disable both motors on the Y/A axis so that the Y axis can be. If you only need to adjust one motor at a time you. Can’Unlock’ the Y and A axis and that will give you independent control. Of the Y and A motors using the’On/Off’ switches. Please note that there. Is a timing belt at the rear of the machine that is used to keep the Y and A. Axis synchronized, so to adjust the motors independently you would need. To loosen one of the pulleys. There are also digital temp gauges below. Each’On/Off’ switch that measure the temperature of the GeckoDrive. G201 stepper drives (the temp probe is attached to the G201 heatsinks). The machine has never had a spindle attached to it but it does have. A’Spindle Out’ 120v plug at the rear of the controller that is software. Controlled using the M3 & M5 command in Mach3 (M3 = On , M5 = off). There is also an extension cord that has already been run from the. Back of the controller to the Z-axis actuator you can see the orange. 120v plug at the top of the z-axis, so all you have to do is mount a. 120v spindle to the z-axis and plug it into the extension cord. There are two 120v power inputs on the back of the controller, the. Main – In’ is what supplies power to the machine and the’Aux- In. Only supplies power to the’Spindle – Out’ the’spindle out’ socket. Is controlled using a 25amp solid-state relay controlled with Mach3. The computer that comes with this machine is a newly refurbished. I have done to it is install a licensed copy of Mach3 software on it. The machine and controller were built using 2040 (2″ x 4″) aluminum. Is something that I bought separately and I believe it is constructed. Using Bosch/Rexroth 30mm square aluminum framing. Has locking casters on it so that it can be moved around easily. Computer stand = 25″w x 25″d x 30-1/2h. Controller = 28″w x 24″d x 4h. CNC Machine (Main Frame) = 30″w x 22″d x 16h. X Axis = 400mm rated travel (415mm max). Y Axis = 300mm rated travel (310mm max). Z Axis = 100mm rated travel (120mm max). X Axis = 450ipm. Y Axis = 400ipm. Z Axis = 150ipm. Parker 404400XRMS-D4 Actuator (20mm pitch ballscrew). Parker OEM 83-93-MO Nema34 Dual-Shaft Stepper. (x2) Parker 404300XRMS-D4 Actuator (20mm pitch ballscrew). (x2) Parker OEM 83-93-MO Nema34 Dual-Shaft Stepper. Parker 404100XRMP-D2 Actuator (5mm pitch ballscrew). Pac-Sci E22NCHT Nema23 Dual-Shaft Stepper. (x4) GeckoDrive G201 7-amp Stepper drives. SoundLogic 4-Axis Breakout Board. Antek 39v 500Watt Power Supply. (x4) 120v Cooling Fans (x2 Intake , x2 Exhaust). HP Compaq Desktop Tower. Intel Core 2 Duo 2.80ghz. With Licensed copy of Mach3. Dell 17 LCD Monitor. Parker 404XR Website Link. Because this item is too heavy. This is available for local pick-up. The item “Custom Parker 404XR CNC Precision Linear Actuator with Ballscrew Mach3 GeckoDrive” is in sale since Tuesday, October 6, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “xyz_axis_cnc_2011″ and is located in Pueblo, Colorado. This item can’t be shipped, the buyer must pick up the item.
- Machine Type: Custom Parker 404XR CNC
- X-Axis Travel Bed: 400mm (16in)
- Y-Axis Travel Bed: 300mm (12in)
- Z-Axis Travel Bed: 100mm (4in)
- Brand: Parker GeckoDrive Pac-Sci
- Control: CNC
- Voltage: 120 V
