1 1/2 HP MOTOR.. COMES WITH COLLETS AND DRILL CHUCK. CAN INSTALL DRO AND POWERFEED AT COST. ALSO HAVE VISES AND HOLD DOWN SETS AT COST. CONTACT ME WITH ANY QUESTIONS OR OFFERS.

The motor casing and headstock are connected, using a more powerful motor, the maximum motor power is 144W, which can process gear 2. Use the spacer to drill round workpieces evenly 3. There are three round holes on the divider. Each round hole has the same ratio of holes. The number of holes on each circle is 36, 40, 48. We can choose them according to our needs. Three-jaw chuck with a maximum working material diameter is 50mm 5. Transformer has over-current protection, over-voltage protection and over-heat protection function. Item Type: Metal Milling Machine. Motor Speed: 12000rpm / min Input Voltage / Current / Power: 12VDC / 5A / 60W Working Materials: Wood, engineering plastics, soft metals gold, silver, copper, aluminum, etc. Maximum Working Material Diameter for Three-jaw Chuck Clamping: 50mm Transformer with over-current protection, over-voltage protection, over-heat protection The hand wheel has a 0.02mm graduation line, which improves the accuracy during processing Motor Power: 144W Module: 0.5, Accuracy: 0.03-0.05mm, Formula: Diameter D = module 0.5 x number of teeth + 1 Center Height: 50mm Z-shaft Travel: 32mm, Y / X-shaft Travel: 145mm Working Materials: Wood, plastic, acrylic, soft metal gold, silver, copper, aluminum, etc. 1 x Metal Milling Machine. 1 x Base Plate. 1 x Power Cable. 1 Bag of Accessories. Our listing price includes the value of goods, packaging cost, and export. Please check with your country’s. We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls. Post a message again because sometimes our message system may block some emails. If you are satisfied with our service, pls. Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better. We strive to keep all our customers satisfy. We will do our up most to exceed your expectations in customer service, communication and dispatching of your orders.

The tool used for milling machine is a milling cutter. The side and front of the milling cutter are both cutting edges. It has certain dangers, so it must be used under the guidance of professionals. 2, the main parts of the machine: such as the spindle box, long base, short base, large slider, small slider, motor blades, connecting blocks, gears, etc. Are made of metal materials. 1, motor speed: 20000 rev / min (optional 12000 rev / min). Input voltage / current / power /: 12VDC / 2A / 24W. 3, Y, Z axis slider stroke: 30mm, X axis slider stroke: 145mm. 5, the maximum clamping size of the vise: 50mm. 6, the hand wheel has a 0.02mm precision scale line, increasing the accuracy of the machine tool workpiece. Applicable processing: wood, soft metal gold, silver, copper, aluminum, etc. , plexiglass, plastic and so on. 7, accuracy 0.07mm. 1x A set of Milling Machine. 1x Speed Control Adapter.

The product image is the actual item you will receive including all contents unless otherwise noted. We do not use stock photos. We are a reseller and not able to provide specific fitment information. However, we can provide additional product specs so that you can determine if the item will work for you. We reserve the right to cancel any order for any reason at any time. We are not responsible for undeliverable addresses. We are not an authorized dealer of this product. If you have any problem with your order / any questions, please send us a message before leaving any type of feedback. We will take care of you! Thank you for shopping WSYB LLC.

MATSUURA #MC-510V VERTICAL MACHINING CENTER. CONTROL: YASNAC MX3. SPINDLE TAPER: BT-35. ATC: 20 POSITION. TABLE SIZE: 15″ X 29″. X, Y, Z TRAVELS: 20″, 14″, 18. WGT: 8500 LBS. PLEASE CONTACT DE OR JOHN WITH ANY QUESTIONS. We have a loading dock and fork lifts with the ability to load any type of truck. Please indicate the following. We can either use your account number or provide a rate quote. Here’s the link to upload to.

HAAS ST-20Y 2019 Low Hours. Questions Welcome, Please Ask. Looking for Swift Sale, Please Make Offer.

Specifications: Type: X Voltage: 220V, 50/60Hz Current: 2.8A Max. Torque: 155kg/cm, 135lb/in R. 0-210 Gross Weight: 6kg Package Dimensions: 291027cm Package Content 1 x APF-260 Power Feed 1 x X-Axis Fix Stand with Bushing 1 x Bevel Gear with Fix Ring 1 x Handle Washer 2 x Stop Blocks 2 x Stop Set 2 x Socket Screws (M8P1.2535) 2 x Socket Screws (M8P1.025) 6 x Small Shims (F26.2F16.20.25t) 2 x Small Shims (F26.2F16.20.1t) 3 x Small Shims (F26.2F16.21.0t) 4 x Large Shims (F43.4F33.40.25t) 2 x Spring Pins 1 x Cable Clamp 1 x User Manual. X Axis Power Feed Table Milling Machine Fit Bridgeport Type Mill Power feed 220V. Please provide the machine type picture before placing the order to judge whether the product meets your needs. The hole diameter of the gear is 16mm. The size of the center hole to the bottom is about 220mm. Set the fix stand on work table, set table bearing bushing on the axis screw, then set the power table feed on the fix stand, take out the gear housing. Use one hand to hold the center transmission shaft. Set the bevel gear on axis screw with the other hand. Then check if the backlash between gears is between 0.1-0.2mm. Add shims (1.0t, 0.25t, 0.1t) if the backlash is too large. Repeat step 2-3 until reaching satisfying backlash. Tighten the handle to start setting socket parallel key and bevel gear. Rotate the handle slightly to feel if any interfere occurs in between. If do, please repeat step 3-4 to add more shims. If not, go to next step. Take out the handle, add proper shim (f43xf33), adjust the backlash between dial & bevel gear and lock with fix ring. Set the handle and tighten, slightly rotate the handle. Normally it should be smooth without any interfere. Finally, set the gear housing and limit switch. Power supply switch and reset switch. The right side of power switch is “ON”. The left side is OFF. Red light will show when machine is on. The red round button on right side is reset switch. Reset button will jump up to cut off the power if the machine overloads. The operator must reduce cutting load, then press reset switch to continue operating. Feed knob and rapid button. Rotate feed knob after power is on. Turn left for left side feeding and vice versa. The button in the middle is “rapid button”. Tool will travel rapidly to left side if you keep pressing the button. Release to make power table feed will back to normal speed. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. NOTE: To stop jog operating, you must first turn “FEED KNOB” TO “0″(OFF) position. Then move “JOG SWITCH” to “FEED” position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Add an auto power table feed to your milling machine! A simple and inexpensive way to increase productivity! Small volume and easy installation. Excellent speed control in the entire range. Jog function operates at any feed speed. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. 1 x APF-260 Power Feed. 1 x X-Axis Fix Stand with Bushing. 1 x Bevel Gear with Fix Ring. 1 x Handle Washer. 2 x Stop Blocks. 2 x Stop Set. 2 x Socket Screws (M8P1.2535). 2 x Socket Screws (M8P1.025). 6 x Small Shims (f26.2f16.20.25t). 2 x Small Shims (f26.2f16.20.1t). 3 x Small Shims (f26.2f16.21.0t). 4 x Large Shims (f43.4f33.40.25t). 2 x Spring Pins. 1 x Cable Clamp. 1 x User Manual. We promise that every item has been sent. But sometimes there is also 0.3% package lost during transport. Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, Please tell us the problem in details and Please con-tact us within 14 days after you receive the package. We will provide you the best solution for any problem with the item. Due to time zones, our reply to your questions may not be immediately. But within above working time, we will reply you-= within 24 hours. If it’s non-workdays, please kindly be patient and wait till Monday. Please feel free to con-tact us if you have any questions.

You might also like. Router Bits Tool 4/6mmShank Spiral Ball Nose End Mill Carbide Milling Cutter. Titanium Coated Router Bit 10PCS Spiral Ball Nose End Mill Carbide Slot Drill. Ball Nose End Mills Tungsten Carbide R0.5-R6.0 2 Flute Router Bit Milling Cutter. 2Flute Spiral Ball Nose End Mill Milling Cutter Aluminum Cutting Tool Router Bit. 6Pcs4mm Shank Engraving Bits End Mill Cutter PCB Milling Bit CNC Router Bit. Die Set Right Hand Machine Plug HSS Screw Thread Tap and Trapezoidal TR Tap 2pcs. Fit steel, casting, aluminum pieces of various material blade. The relevance of a wide range of capacity chip a large space, good chip disposal planar milling finishing applicable large rake angle, cutting a small load. 1 Set Lathe Milling Cutter. You may also like. TCT Hole Saw Cutter Carbide Drill Bit for Metal Steel Alloy Stainless fit Dewalt. Bi Metal Hole Saw Drill Bit for Wood& Plastic& Iron Sheet Cutter with Arbor 80mm. 4/6/7/8 Inch Blue Coated Circular Saw Blade TCT Carbide Tipped Wood Cutting Disc. Pink Magnetic Screwdrivers Set 8pcs 4 Flat and 4 Phillips Screwdriver Hand Tool. 33PC Cordless Electric Screwdriver & Glue Gun USB Rechargeable Tool Kit W/ Bits. 3PC+ HSS Mini Circular Saw Blade Wood Cutting Blade Rotary Tool 54.8mm Mandrel.