Eisen S-2AH milling machine head, R8 taper, 3 HP, 220V, 3-phase. High Precision Variable Speed Milling Head. Bring Wornout Milling Machine Back to Life Spindle vibration? Fix it once and for all with Eisen’s replacement milling head. It’s a Direct Bolt-on Replacement for Bridgeport 2J head (vari-speed) or J head (step-pulley) or the milling heads on imported Bridgeport-type knee mills. High Precision You Can Count On Our milling spindles are hardened, precision ground and chromed. The spindle is supported by high precision preloaded bearings that can also handle high thrust load. Spindle runout is within 0.00015. Avoid the downtime and uncertainty of rebuilds. A direct replacement is a straight forward and economical solution. Satisfaction Guaranteed We thrive on repeat business. That’s the best testament to the quality of our milling heads. Specifications Motor type: Variable Speed Motor Power: 3 HP Spindle Taper: R8 Quill Travel: 5″ Quill Diameter: 3 3/8″ Quill power feeds: 0.0016″, 0.0032″, 0.0059/rev Power requirement: 220 volt, 3 phase Made in Taiwan (220V is the default, please notify us if 440V is needed). Please note residential service or lift-gate service will cost extra. We’ll help you load the milling head onto your truck for free. Installation Notes You would need a forklift or a hydraulic lift to swap out the old head and bolt-on the new one. Milling head’s net weight is about 250 lbs. If You have any questions regarding this item, please let us know we’ll be happy to help. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “eisenmachineryinc” and is located in this country: US. This item can be shipped to United States.

• Brand: Eisen Machinery
• Spindle Horsepower: 3
• MPN: S-2AH
• Model: S-2AH
• Highest Spindle Speed (RPM): 2501 – 3000
• Make: Eisen
• Type: Milling Head

Bridgeport Horizontal Milling Machine 9×32″ Bed 16″Knee Travel 1/3Hp 3Ph 220V. Used, in Good Working Condition, Tested. This was setup for horizontal drilling. Has a 1/4 Chuck. Bed is 9×32″ Ha 8×14″ travel. Knee travel is 16. 1/3 hp 3phase motor. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “arrowindustrialsales” and is located in this country: US. This item can be shipped to United States.

• Brand: Bridgeport
• Size: Length: 52 in. Width: 48 in. Height: 66 in.

Eisen S-2AH milling machine head, R8 taper, 3 HP, 220V, 3-phase. EISEN S-2AH High Precision Variable Speed Milling Head. Bring Wornout Milling Machine Back to Life Spindle vibration? Fix it once and for all with Eisen’s replacement milling head. It’s a Direct Bolt-on Replacement for Bridgeport 2J head (vari-speed) or J head (step-pulley) or the milling heads on imported Bridgeport-type knee mills. High Precision You Can Count On Our milling spindles are hardened, precision ground and chromed. The spindle is supported by high precision preloaded bearings that can also handle high thrust load. Spindle runout is within 0.00015. Avoid the downtime and uncertainty of rebuilds. A direct replacement is a straight forward and economical solution. Satisfaction Guaranteed We thrive on repeat business. That’s the best testament to the quality of our milling heads. Specifications Motor type: Variable Speed Motor Power: 3 HP Spindle Taper: R8 Quill Travel: 5″ Quill Diameter: 3 3/8″ Quill power feeds: 0.0016″, 0.0032″, 0.0059/rev Power requirement: 220 volt, 3 phase Made in Taiwan (220V is the default, please notify us if 440V is needed). Please note residential service or lift-gate service will cost extra. We’ll help you load the milling head onto your truck for free. Installation Notes You would need a forklift or a hydraulic lift to swap out the old head and bolt-on the new one. Milling head’s net weight is about 250 lbs. If You have any questions regarding this item, please let us know we’ll be happy to help. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “eisenmachineryinc” and is located in this country: US. This item can be shipped to United States.

• Brand: Eisen Machinery
• Spindle Horsepower: 3
• MPN: S-2AH
• Model: S-2AH
• Highest Spindle Speed (RPM): 2501 – 3000
• Make: Eisen
• Type: Milling Head

MACHINIST DYNA POWER MADE IN SPAIN WITH TABLE SIZE 48″x10″. MANUAL MILLING MACHINE IN GOOD CONDITION RECENTLY RECONDITIONED. ALL BEARINGS ON THE HEAD AND NUTS FOR X AXIS AND Y AXIS HAS BEEN CHANGED. WITH Y AXIS AUTO FEED. VISE IS NOT INCLUDED. X AXIS TRAVEL IS 32. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “pythia16″ and is located in this country: US. This item can be shipped to United States.

• Country/Region of Manufacture: Spain
• Machine Type: Milling Machine
• Table Length: 48
• Power Source: Electric
• Function: Milling
• Brand: MACHINIST DYNA POWER
• Table Width: 10
• Control: Manual
• Voltage: 220 V

Light Source: LED Bulbs Is Bulbs Included: Yes Is Dimmable: No. Switch Type: Push Button Switch. Features: explosion proof light. Characteristics: Waterproof, oilproof, dustproof, Explosion-proof. Product material: Aluminum alloy + tempered glass. Suitable for: Garage, workshop, factory, Gao Peng. Suitable for 1: CNC machine, lathes, milling machines, punching machines. Suitable for 2: Industrial lighting. Suitable for 3: Workshop working light. Suitable for 4: garage light. Voltage: 12 volts, 24 volts, 36 volts, 220 volts. Wire length: 1.2 meters. Material: aluminum alloy + glass + ABS. Lamp holder type: four-hole fixed lamp holder. 40W 220V 1250mm fixed work light. Use high quality LED lighting source. Applications: CNC machines, sewing machines, milling machines, lathes, factories, construction sites, workshops, garages, machines, CNC machine tools, work, architectural lighting, outdoor lighting. Unit Type: piece Package Weight: 0.075kg 0.17lb. Package Size: 1cm x 1cm x 1cm (0.39in x 0.39in x 0.39in). This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “switchtools” and is located in this country: CN. This item can be shipped worldwide.

• Voltage: 110V-220V
• Wattage: LED 40W 110-220V
• Spindle Horsepower: —-
• Machine Type: Router Engraver Milling Machine
• Model Year: —-
• Power Source: Electric
• X-Axis Travel Bed: —-
• Y-Axis Travel Bed: —-
• Spindle Taper: —-
• Function: Milling
• Brand: Unbranded
• Control: CNC

Mill works but the auto feeds do not. Has a DRO and VFD so it runs on single phase 220. Comes with vice, VFD manual and hold down kit. We basically used it as a drill press to do bolt circles. I can help disconnect it and help get it into the driveway, it is up to you to take it from there. The driveway is wide so a Ryder with liftgate will fit to make it easier. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “mopar_buyer” and is located in this country: US. This item can be shipped to United States.

• Model: Supermax
• Machine Type: Vertical Milling Machine
• Function: Milling
• Brand: Supermax
• Voltage: 220 V

Current : no load current 5A max 13A. Speed : 800rpm 18000rpm max. Joint of nose : BT30 Taper. 4 Bearing, 7008×2 7006×2, all ceramic p4 china brand. Attention VFD input 220v single phase, output is 380v 3 phase. 1pcs spindle ATC BT30 5.5kw. 1pcs airtac 5 way vale 24VDC. 1pcs airtac air regulator with filter. 1pcs HSD vfd input 220v single phase output 380v 3 phase. 6pcs NBT30 ER25 holder. 12pcs collect ER25 variable size inch type. 1pcs UM25, ER25 open tool. Pre setting vfd for spindle and use VFD protec ATC sytem. 5.5kw atc spindle, slot mill, tool 6mm deep 6mm. Spindle atc bt30 5.5kw, 60mm face milling. Spindle bt30 5.5kw, drill 10mm aluminium at 2000rpm. Spindle 5kw bt30 facing milling. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Workholding & Toolholding\Toolholding\Spindles”. The seller is “nhatson.elec” and is located in this country: VN. This item can be shipped worldwide.

• Modified Item: No
• Country/Region of Manufacture: Unknown
• Custom Bundle: No
• Brand: Unbranded
• Item Type: Build In spindle

ENCO Drill Mill Drilling Milling Machine Gear Head FM 2508 M 1 Phase 220v Tools. This Lathe could be inspected under power in our warehouse in Oxnard, CA 93033. The item “ENCO Drill Mill Drilling Milling Machine Gear Head FM 2508 M 1 Phase 220v Tools” is in sale since Thursday, November 11, 2021. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “amiron_machinery” and is located in Oxnard, California. This item can’t be shipped, the buyer must pick up the item.

• Machine Type: Milling Machine
• Function: Drilling
• Brand: ENCO

X-AXIS POWER FEED- Power Feed X-Axis, Voltage: 220V, 60Hz, Rotate Speed: 200 Rpm, Max Torque: 450 in-lb, Max Feed Rate: 650mm/min, Max Return Speed: 850mm/min, Dimension: 8 x 4.5 x 13 inches. QUIET & RAPID OPERATION- With speed adjust knob, speed can be adjusted according to operator’s requirement, ranging from 0-9. Jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. DURABLE & LONG LASTING- Safe design helps to protect transmission gear and electronic components; two gears of this power table feed will not mesh and wear at the same spot, maximizing durability and longevity. ERGONOMIC DESIGN- Power feed is equipped with safety feature to protect transmission gear and electronic components as to meet the requirements of ergonomics. EASY SETUP- Small volume and easy installation, noiseless direction changes. Fit almost any vertical knee type milling machine with the 5/8 shaft end. Milling Machine Power Feed. Power Feed X-Axis, Voltage: 220V, 60Hz, Rotate Speed: 0-200 RPM, Max Torque: 450 in-lb, Max Feed Rate: 650mm/min, Max Return Speed: 850mm/min, Dimension: 8 x 4.5 x 13 inches. Rotate Speed: 0-200 RPM, Max Feed Rate: 650mm/min. Milling machine power feed features noiseless direction changes and direction control knob for easy and rapid operation. The two gears of this power table feed will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Power table feed won’t vibrate or strain in low speed. Power feed is equipped with safety feature to protect transmission gear and electronic components as to meet the requirements of ergonomics. Dimension: 8 x 4.5 x 13 inches. This small volume and easy installation X-axis power feed is designed to automate the feeding process on Bridgeport type milling machines. Suitable models including vertical turret milling machine, drilling and milling machine and other machinery. 220V Power Feed Milling Machine With Rotate Speed 200. Our brand new Mill Power Feed featuring Max. Rotate speed 200Rpm, power torque 450 in-lb and Max. Feed rate: 650mm/min, similar knee type milling machines, including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… Quiet & Rapid Operation. Durable & Long Lasting. Rotate Speed: 200 RPM. Max Torque: 450 in-lb. Max Feed Rate: 650mm/min. Max Return Speed: 850mm/min. Gross Weight: 16.5 lbs. 1 x Power Feed For Milling Machine. 8 x Adjustable Pad. 2 x Travel Stop Assembly. 1 x Bevel Gear. 1 x Dial Nut. 1 x Locking Nut. 1 x Product Manual. Power Feed Milling Machine. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. California Warehouse: City of Industry, CA. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. Caifornia Warehouse: 18501 Arenth Ave, City of Industry, CA 91748. 300 W Airtex Blvd, Suite 200, Houston, TX 77090. 2125 Gateway Blvd, Hebron, KY 41048. 1000 High Street, Perth Amboy, NJ 08861. The item “VEVOR 220V Power Feed Milling Machine Al-310S X-Axis Torque 450 In-lb 200PRM” is in sale since Tuesday, March 24, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “dairuirui122_3″ and is located in Perth Amboy, New Jersey. This item can be shipped to United States, Canada, Mexico.

• Brand: VEVOR
• MPN: UGFSA0081231563961342
• Model: 310X
• Country/Region of Manufacture: China
• Power Source: Electric
• Voltage: 220V, 50Hz
• Control: Manual
• Function: Milling
• Custom Bundle: No
• Modified Item: No
• Machine Type: Milling Machine
• Max Spindle Speed (RPM): 0-200 RPM
• Rotate Speed: 200 RPM
• Max Torque: 450 in-lb
• Max Feed Rate: 650mm/min
• Max Return Speed: 850mm/min
• Dimension: 8 x 4.5 x 13 inches
• Gross Weight: 16.5 lbs

Made of aluminum material. Rotate Speed: 200 RPM, Max Torque: 450in-lb. 7 x 3.5 x 12inc. QUIET & RAPID OPERATION. With speed adjust knob, speed can be adjusted according to operator’s requirement, ranging from 0-9. Jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. DURABLE & LONG LASTING. Safe design helps to protect transmission gear and electronic components; accessories of this power table feed will not mesh and wear at the same spot, maximizing durability and longevity. Power feed is equipped with safety feature to protect transmission gear and electronic components as to meet the requirements of ergonomics. Small volume and easy installation, noiseless direction changes. Fit almost any horizontal knee type milling machine and other small machinery. Milling Machine Power Feed. Power Feed X-Axis, Voltage: 220V, Rotate Speed: 0-200 RPM, Max Torque: 450 in-lb, Dimension: 9 x 4.5 x 14 inches. Rotate Speed: 0-200 RPM, Max Feed Rate: 650mm/min. Milling machine power feed features noiseless direction changes and direction control knob for easy and rapid operation. Equipped with several necessary accessories, this not only increases durability and longevity but even reduces noise over time. Power table feed won’t vibrate or strain in low speed. This small volume and easy installation X-axis power feed is designed to automate the feeding process on Bridgeport type milling machines. Suitable for horizontal installation models including turret milling machine, drilling and milling machine and other small machinery. Power Feed Milling Machine With Rotate Speed. If you want to get the most out of your milling drilling machine you really need a power feed. This power feed comes with everything required to start milling with exact contro. Our brand new Mill Power Feed featuring Max. Rotate speed 200Rpm, power torque 450 in-lb, is for bridgeport and similar knee type milling machines. Quiet & Rapid Operation. Durable & Long Lasting. Rotate Speed: 0-200 RPM. 1 x Power Feed Milling Machine. 1 x Necessory Accessories. Power Feed Milling Machine. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. California Warehouse: City of Industry, CA. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. Caifornia Warehouse: 18501 Arenth Ave, City of Industry, CA 91748. 300 W Airtex Blvd, Suite 200, Houston, TX 77090. 2125 Gateway Blvd, Hebron, KY 41048. 1000 High Street, Perth Amboy, NJ 08861. The item “Power Feed X-Axis 200RPM 450in-lb for Bridgeport Type Milling Machine 220V” is in sale since Saturday, May 9, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “dairuirui122_3″ and is located in Perth Amboy, New Jersey. This item can be shipped to United States, Canada.

• Brand: VEVOR
• MPN: NBSUG0021191574753692
• Country/Region of Manufacture: China
• Power Source: Electric
• Voltage: 220V
• Control: Manual
• Function: Milling
• Custom Bundle: No
• Modified Item: No
• Machine Type: Milling Machine
• Max Spindle Speed (RPM): 0-200 RPM
• Material: Aluminum
• Rotate Speed: 0-200 RPM
• Max Torque: 450in-lb
• Dimension: 7 x 3.5 x 12inches (17x9x30cm)
• Package Content 1: Power Feed Milling Machine
• Package Content 2: Necessory Accessories