The tool used for milling machine is a milling cutter. The side and front of the milling cutter are both cutting edges. It has certain dangers, so it must be used under the guidance of professionals. 2, the main parts of the machine: such as the spindle box, long base, short base, large slider, small slider, motor blades, connecting blocks, gears, etc. Are made of metal materials. 1, motor speed: 20000 rev / min (optional 12000 rev / min). Input voltage / current / power /: 12VDC / 2A / 24W. 3, Y, Z axis slider stroke: 30mm, X axis slider stroke: 145mm. 5, the maximum clamping size of the vise: 50mm. 6, the hand wheel has a 0.02mm precision scale line, increasing the accuracy of the machine tool workpiece. Applicable processing: wood, soft metal gold, silver, copper, aluminum, etc. , plexiglass, plastic and so on. 7, accuracy 0.07mm. 1x A set of Milling Machine. 1x Speed Control Adapter.

G8689Z 4″ x 16″ Mini Milling Machine. An ideal benchtop milling machine for the home hobbyist. The G8689Z 4″ x 16″ Mini Milling Machine can power through up to 1/2″ drilling, 1/2″ end mills, and 1 facing for the consistent results you need. This benchtop mill features the highly stable R8 spindle that offers versatility, quick and easy tool changes, and exceptional accuracy. The variable-speed control and gear drive save you time and hassle as you switch between projects. The G8689Z has two speed ranges: low range 0-1100 RPM, and high range 0-2500 RPM. Modify the spindle height with the rapid downfeed, or use the micro downfeed to adjust down to 0.001″ (one full revolution is 0.060″). The headstock adjusts up and down the column and tilts 45° left or right relative to the table, and adaptable dovetail ways offer precision and rigidity. You can set the limit block to restrict the amount of head travel for repeated drilling of the same depth. This mini milling machine also includes a clear chip guard on the spindle and a rubber chip guard on the ways for safety. The G8689Z manual was written by our U. Based Technical Documentation Department and is packed with useful information. Made in an ISO 9001 factory. Motor: 1/2 HP, 110V, single-phase, 4.5A. Spindle speeds: Variable, 0-1100 and 0-2500 RPM. Maximum distance spindle to table: 10-1/2. Maximum distance spindle-to-column: 6-3/8. Table size: 15-3/4″ L x 3-5/8″ W. Table travel (longitudinal): 9-1/8. Table travel (cross): 4. Head tilt: 45° L/R. Drilling capacity: 1/2 mild steel. End milling capacity: 1/2. Face milling capacity: 1. Overall size: 20″ W x 20″ D x 30 H. 1/2 drilling capacity in steel and cast iron. Two variable-speed spindle ranges on a geared drive. Fine feed head control. Zero-setting dials on handwheels w/0.001 graduations. Adjustable dovetail ways on column. Clear chip guard on spindle. Rubber chip guards on ways. 1/32″-1/2″ JT33 drill chuck. R-8 x JT33 arbor. Two 3/8-16 T-slot nuts. 3, 4, 5, 6mm hex wrenches. 8 x 10, 14 x 17, 17 x 19, 36mm open-end wrenches. We are committed to your satisfaction. What Are My Options? Since our inception in 1983, Grizzly Industrial®, Inc. Has grown into one of the largest machinery companies in the United States. Our products can be found in all sizes of shops from the large industrial production users to the smaller cabinet and machine shops. We have the widest product selection under one brand in the world and we sell direct to the user, cutting out the dealer network, and resulting in lower prices to you. We ARE Grizzly Industrial, Inc. We reserve the right to correct errors and omissions in our listings, including specifications, photographs, and pricing. Thank you for your interest.

For Sale by Equipment Recycle is a. Servo Impact 2 7844-200 7405 CNC Mini Mill Drill Milling Machine. The specs on this mill are 120V, 50/60Hz, and 15A. The silver drill head has model 7405 on it and the black piece is model 7844-200. It comes with a Bijur Fluid Flex D153 attached. This machine is on a custom table. This item was removed from a local government facility. It was pulled from a working environment. There is no controller that comes with this unit. Unit shows some wear and light oxidation from previous owner. There are some metal shavings on the machine as well. Please see photographs for clarification. Here is your chance to own this for a fraction of retail! We are here to help! 4 = Like New 3 = Good 2 = Poor-Fair 1 = As-Is. At Equipment Recycle we shoot for the stars. We want all 5 stars from you and will do what it takes to earn them. So before leaving feedback or low star ratings give a chance to correct any issue. Our feedback settings are automated. We believe that the customer comes first and we go above and beyond to correct any issue that may occur. We are a small family run equipment broker and consignment company. We offer a market analysis on your product and then give you the option to sell or consign your item with us. We believe that we can sell anything and there is no job or product to big. Let us sell your equipment and help you or your company grow. There is a large customer base out there just waiting to be reached and Equipment Recycle is the company to reach them for you. Let Equipment Recycle bring the world to you! Buyers without these will be subject to a lift gate charge. The sale of this item may be subject to regulation by the Food and Drug Administration and state and local regulatory agencies. Equipment Recycle is the consignee of most of the items we sell. Equipment Recycle has used its best efforts to inspect the item(s) for sale and create descriptions and furnish photographs that fairly and adequately depict the type, condition and image of the goods at the time of sale.

Specification Machine Type: Ct125 Power: 180 W Voltage: 110 V Size: 523041 Cm/20.511.5816.14in Wight: 22 Kg Package Size: 553048 Cm/21.711.818.9in Detailed Product Information 1. Turning Maximum Workpiece Rotation Diameter: 125mm/4.9in Maximum Workpiece Length: 180mm/7.1in Maximum Workpiece Rotation Diameter on the Tool Rest: 60mm/2.4in Spindle Through Hole Diameter: 9mm/0.35in Spindle Taper Hole: Mt. 1 Number of Metric Threads Processed: 8 Machining Metric Thread Pitch Range: 0.4-1.5mm/0.02-0.06in Number of Inch Threads Processed: 8 Machining Inch Thread Pitch Range: 0.0028-0.00551 /N Longitudinal Feed Series: 2 Longitudinal Feed of Spindle per Rotary Tool Holder: 0.07-0.14mm/0.003-0.005 Tailstock Sleeve Stroke: 18mm/0.71in Taper Hole of Tailstock Sleeve: Mt. 1 Spindle Speed Range a. Ct125 Mini Electric Lathe Drilling Milling Machine 3 in 1 Metalworking Equipment. Specification Machine Type: Ct125 Power: 180 W Voltage: 110 V Size: 523041 Cm/20.511.5816.14in Wight: 22 Kg Package Size: 553048 Cm/21.711.818.9in Detailed Product Information. Maximum Workpiece Rotation Diameter: 125mm/4.9in Maximum Workpiece Length: 180mm/7.1in Maximum Workpiece Rotation Diameter on the Tool Rest: 60mm/2.4in Spindle Through Hole Diameter: 9mm/0.35in Spindle Taper Hole: Mt. This Ct125 3-in-1 Micro Multi-function Drilling and Milling Lathe Machine Adopts Cast Iron Body and All Metal Gears. It Is Mainly Used for the Outer Circle, Inner Hole, End Face, Taper and Metric and Inch Thread Processing of Various Rotating Parts. It Is Suitable for Families, Studios, Schools, and Various Small Repair Workshops. The Control Panel of the Machine Tool Is Simple and Easy to Operate. The Machine Has High Precision Spindle and Quality Electronic Control System The Bed Saddle Is Easy to Fix Fixtures, Molds, Pliers, and Other Tools. The High-power All-copper Asynchronous Motor Provides Strong Power. Dovetail Rail: the Bed Adopts Dovetail Guide Rail, the Contact Surface Is Larger and More Stable. Three-jaw Chuck: This Machine Has 80mm High Precision Three-jaw Chuck. Drilling and Milling Head: It Can Be Rotated 360°, Raised and Lowered Within a Range of 80mm. Drilling and Milling Gears/Pulleys: Through the V-belt Position, the Drilling and Milling Spindle Can Achieve 10 Kinds Rotate Speed. Compact and Easy to Install. Easy to Operate, No Training Required. This Machine Can Process Various Non-ferrous Metals Such As Titanium, Stainless Steel, Steel, Iron, Aluminum, Copper, and Soft Materials Such As Wood and Nylon. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday.

Youth Activity Center, School General Technical Room, Science and Technology Activity Room Equipment, Science and Technology Museum Student Science and Technology Creation. Main parts of the machine. The main components of the main shaft box, intermediate block, connecting block, tailstock, large slider, small slider, hand wheel, support and so on are made of metal. The quality of the product is improved, more durable and more precise. Input voltage AC100V240V 50/60HZ. Output voltage DC12V 2A. Motor rated power 24W. Motor speed High speed electricity 20000r/min±15%. Low speed motor 10000r/min ± 15%. Spindle speed High speed motor 3000r/min±15%. Low speed motor 1600r / min ± 15%. Large slider stroke 45mm. Small slider stroke 35mm. Chuck specifications? 1, ? 2, ? 2.5, ? 3, ? 3.5, ? 4, ? 5, ? 6. Handle scale 0.1mm/division. Processing ability to process soft metals such as copper and aluminum. 1x A set of mini drilling machine.

3/4 Axis 1500W Mini CNC 6040T Engraving Drilling Milling Machine Router Frame. This CNC 6040T machine is suitable for industry, Technology Research, Advertising Design, Arts Creation, Teaching, Student Project and Hobby Purposes. It can work with various materials(metallic & non-metallic), such as: wood, pmma or other plastic, MDF board, native wood, PVC, Acrylic, wood, composite board plywood. And soft metal, like aluminum, copper and silver to engrave them into 3D/2D works etc. It can used for engraving: advertising signs, PCB, nameplates, badges, seals, bronzing plate, aluminum alloy, acrylic plates, ABS resin double color plate, PVC foaming board, indentation plates, signs, construction models. Instrument panels, wooden products, etc. The mini CNC router Frame is movable. The machine can connect with computer as other external device such as printer, scanner.. With the assist of the CNC ROUTER 6040T, your design idea will be real-time display. CNC engraving machine parameters. X, Y, Z Working Area: 600(Y)390(X)120(Z)mm. Lathe structure: 6061/6063 Aluminium alloy. Y axis—1605 Ball Screws. Z axis—1204 Ball Screws. X axis—High intensity Chromeplate shaft. Y axis—High intensity Chromeplate shaft. Z axis—High intensity Chromeplate shaft. The spindle motor must connect with the VFD. It cannot directly connect with the supply voltage (AC 220V). Please don’t change the data setting of the VFD if you are not professional technicians, or it might damage the spindle motor. Material: 304 stainless steel, Copper coil, Pressure cast aluminum pipe water jacket. VOLTS, current, power: AC 220V, 50Hz, 5A. 1.5 KW VFD. Spindle speed: 24000 rpm. Max working frequency: 400Hz. Principal axis collet: ER11collet, Standard configuration :6mm. Speed mode: By adjusting the VFD output voltage and operating frequency from 0-24000RPM. Lubrication way: lubricated by high grease. Repeat accuracy: 0.05mm. Spindle precision: radial beat acuities 0.03mm. Carving Instructions: G code / TAB files / nc file / NCC files. Communication interface: through USB connection with computer. Support system: windows XP / win7 32bits system. Carving speed: 0-2500mm/min(different materials differ). Operating Voltage: AC 220V. Control unit: Toroidal transformer + PWM power supply module + TB6560 stepping motor drive. Command code: G code. Protection: Emergency stop button. 1.5KW water-cooled VFD. Is available operating for long time, which can reinforced the processing ability of the machine and can be used to process aluminum alloy and hard wood. Water cooling spindle works more stable and durable. High quality accurate ball Screws drive make the engraving more precision. Anti-blackflash, high precision, long life circle. Assembling and locating the CNC machine on steady desk well. Make sure that your computer has a USB port output. Place the control box in a ventilated dry place where there is no dust, no moisture. Connecting the control box with the CNC machine and you computer and make sure the plug will not come off. Correctly connect the machine with the controller. Don’t suspended the cable which connect the Spindle motor with axis(X, Y, Z, A). It will damage the driver of the controller. Correctly install the Spindle motor and the heat pump. The heat pump should be covered completely in the water, then turned on the electric current to check whether the water-cooling system working well. Before turn on the machine, please check all the cable and water- cooling system to make sure they are working fine. You can enjoy making you dream with using our CNC machine now. 4 AXIS 1500W USB PORT+RC. Notes:Please prepare a computer with USB Interface. 1X main unit (Frame). 1X main unit (working base). 1X Sinal cable for A axis. 1X 25pin Parallel lines. 10X 47mm round head. 6X 410mm black Inner six angle screw with nut. 8X 520mm black Inner six angle screw. 4X 58mm Flat Philip’s head screw with nut and gasket. 8X 624mm BALCK FLAT Inner six angle screw. 2X six angle Wrench(3mm). 2X six angle Wrench(4mm). Suitable for PCB, wood, Plexiglass, PVC, Crystal Acrylic, RESIN, Plastic, SEALS, MDF, COMPOSITE, Aluminum material, Copper, Iron. It can work with various materials(metallic & non-metallic), such as: wood, pmma or other. Plastic, MDF board, native wood, PVC, Acrylic, wood, composite. Like aluminum, copper and silver to engrave them into. It can used for engraving: advertising signs, PCB, nameplates, badges, seals, bronzing plate, aluminum alloy, acrylic plates, ABS resin double color plate, PVC foaming board, indentation plates, signs, construction models, instrument panels, wooden products, etc. The machine can connect with computer as other. External device such as printer, scanner.. CNC Engraving Machine Parameters. X, Y, Z Working Area : 600(Y)390(X)120(Z)mm. Lathe structure : 6061/6063 Aluminum alloy. Y axis :1605 Ball Screws. Z axis:1204 Ball Screws. X axis:High intensity Chromeplate shaft. Y axis:High intensity Chromeplate shaft. Z axis:High intensity Chromeplate shaft. 1, The spindle motor must connect with the VFD. 2, It cannot directly connect with the supply voltage (AC110V). 3, Please don’t change the data setting of the VFD if you are not professional technicians, or it might damage the spindle motor. Material:304 stainless steel, Copper coil, Pressure cast aluminum pipe water jacket. VOLTS, current, power: AC110V-220V/50Hz, 5A, 1.5KW VFD. Spindle speed : 24000 rpm. Max working frequency : 400Hz. Speed mode:By adjusting the VFD output voltage and operating frequency. Repeat accuracy:0.05mm. Spindle precision:radial beat acuities 0.03mm. Communication interface:through USB connection with computer. Maximum Idle speed:1500mm/min. Working Speed :50-1500mm / min (different material with different speed settings). Control unit:Toroidal transformer + PWM power supply module + TB6560 stepping motor drive. Computer connection:USB port. Command code:G code. Protection:Emergency stop button. 1, The NEW 1.5KW water-cooled VFD is available operating for long time, which can reinforced the processing abil. Ty of the machine and can be used to. Process aluminum alloy and hard wood. 2, water cooling spindle works more stable and durable. 3, High quality accurate ball Screws drive make the engrving more precision. Make sure that your computer has a 25pin parallel port output. L box in a ventilated dry place where there is no dust, no moisture. Damage the driver of the controller. L the Spindle motor and the heat pump. The heat pump should be covered completely in the water, then turned on the electric current to. Check whether the water-cooling system working well. Waterproof design, very durable, anti-dirt, oil spray. Power by USB port. Dimensions: 22 x 8 x 3cm. The usb self-check light, you can type the ” scroll” on the keyboard to activate it. Directional motion control: X+, X-, Y+, Y-, Z+, Z-, A+, A. Feed rate control: F+, F. Jog rate: J+, J. Spindle speed: speed up, slow down. Programming: E-stop, cycle start, spindle on/off, Redo, single step, original point. 3 AXIS 1500W USB PORT. Suitable for PCB, wood, Plexi glass, PVC, Crystal Acrylic, RESIN, Plastic, SEALS, MDF, COMPOSITE, Aluminum material, Copper. This CNC 6040 machine is suitable for industry, Technology Research, Advertising Design, Arts Creation, Teaching, Student Project and Hobby Purposes. Like aluminum, copper and silver to engrave them into 3D/2D works etc. It can used for engraving: advertising signs, PCB, nameplates, badges, seals, bronzing plate, aluminum alloy, acrylic plates, ABS resin doublecolor plate, PVC foaming board, indentation plates, signs, construction models, instrument panels, wooden products, etc. Cnc engraving machine parameters. It cannot directly connect with the supply voltage (AC220V). VOLTS, current, power: AC110 /60Hz, 5A, 1.5KW VFD. Max working frequency: 60Hz. Support system: Windows XP/Win7. Computer connection: USB port. The NEW 1.5KW water-cooled VFD is available operating for long time, which can reinforced the processing abilty of the machine and can be used toprocess aluminum alloy and hard wood. High quality accurate ball Screws drive make the engrving more precision. Otherwise, It will damage the driver of the controller. The Spindle motor and the heat pump. Before turn on the machine, please check all the cable and water-cooling system to make sure they are working fine. (3 AXIS 1500W USB PORT+RC). Mode: By adjusting the VFD output voltage and operating frequency from 0-24000RPM. Is available operating for long time, which can reinforced the processing abil. High quality accurate ball Screws drive make the engr. Flash, high precision, long life circle. (3 AXIS 1500W Parallel Port). Notes:Please prepare a computer with DB25 parallel Interface. This machine needs to connect to a computer through its controller box with a. Parallel cable (both included). It is not recommended to connect to a notebook through a. Parallel port as the power saving features tend to interrupt the data flow. It is also not recommended to connect to a computers with 64 bit versions of Windows due to problems with the Parallel port driver. Suitable for PCB, wood, Plexiglass, PVC, Crystal Acrylic, RESIN, Plastic, SEALS, MDF, COMPOSITE, Aluminum material, Copper. Lathe structure:6061/6063 Aluminium alloy. Y axis:1204 Ball Screws. Spindle speed:24000 rpm. Max working frequency:400Hz. Principal axis collet:ER11collet, Standard configuration :6mm. Mode:By adjusting the VFD output voltage and operating frequency from 0-24000RPM. Lubrication way:lubricated by high grease. Carving Instructions:G code / TAB files / nc file / NCC files. Communication interface:through parallel connection with computer. Support system:windows XP / win7. 3, High quality accurate ball Screws drive make the engr. Connecting the control box with the CNC machine and you computer. And make sure the plug will not come off. (3 AXIS 1500W Parallel Port+RC). Notes: Please prepare a computer with DB25 parallel Interface. PCB, wood, Plexiglass, PVC, Crystal Acrylic, RESIN, Plastic, SEALS, MDF, COMPOSITE, Aluminum material, Copper. This 6040T machine is suitable for industry, Technology Research, Advertising Design, Arts Creation, Teaching, Student Project and Hobby Purposes. The mini router Frame is movable. With the assist of the ROUTER 6040T, your design idea will be real-time display. X, Y, Z Working Area: 600(Y)390. Y axis–1605 Ball Screws. Z axis–1204 Ball Screws. X axis–High intensity Chromeplate shaft. Y axis–High intensity Chromeplate shaft. Z axis–High intensity Chromeplate shaft. It cannot directly connect with the supply voltage (AC110V). VOLTS, current, power: AC110 /60Hz, 5A. Principal axis collet: ER11collet, Standard configuration: 6mm. Communication interface: through parallel connection with computer. Environment: Windows XP / Win7, 32bits system. Computer connection: Parallel port. 1.5 KW water-cooled VFD. Ty of the machine and can be used to process aluminum alloy and hard wood. Compatability: fit for Type3/ArtCAMParameter. Assembling and locating the machine on steady desk well. Connecting the control box with the machine and you computer and make sure the plug will not come off. Installing a control Drive on your computer. Llowing our manual or guideline to set. You can enjoy making you dream with using our machine now. (5 AXIS 1500W USB Port). Make sure that your computer has a 25pin USB port output. Don’t suspended the cable which connect the Spindle motor with axis(X, Y, Z, A, B). Highlights of water cooling system. It can cool the spindle and protect the machine. Avoid the spindle burn out. Can engrave the high hardness or metal. It can improve the efficiency and accuracy of the machine. 2X Sinal cable for A B axis. This 6040T machine is suitable for industry, Technology Research. Advertising Design, Arts Creation, Teaching, Student Project and Hobby Purposes. With the assist of the ROUTER 6040, your design idea will be real-time display. X, Y, Z Working Area:600(Y)390(X)120(Z)mm. Y axis:1605 Ball Screws. Tips:1, The spindle motor must connect with the VFD. Speed mode:By adjusting the VFD output voltage and operating frequency:from 0-24000RPM. Software environment:32-bit version of Windows 2000, Windows XP, Windows Vista, or Windows 7 (64-bit versions will not work). Non-integrated Video Card with 32MB RAM(Large G-code files, especially 3D files will require a video card with 512MB RAM or higher). Working speed:50-1500mm/min(different material with different speed settings). Anti-black flash, high precision, long life circle. Note:We only sell machine without software. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday.

Dxm-rm-top{font-size:13px;max-width: 100vw;}. Dxm-rm-top ul{margin:0;padding:0}. Dxm-rm-top a{text-decoration:none}. Dxm-rm-top ul{list-style-type:none}. Dxm-rm-head{overflow:hidden;position:relative;padding:6px 12px;width:100vm;min-height: 20px;}. Dxm-rm-head-title{vertical-align:middle;max-width:calc(100% – 75pt)}. Dxm-rm-body{margin:0 0 0 -20px}. Dxm-rm-body:after {display: block;clear: both;height: 0;content: “\0020″}. Dxm-rm-body li{position:relative;float:left;display:inline-block;box-sizing:border-box;padding:10px 0 10px 20px;width:16.66%}. Dxm-rm-body li a{display:block;padding:5px;font-size:13px;border:1px solid #fff;}. Dxm-rm-body lipadding-left:20px;width:20%! Dxm-rm-body lipadding-left:18px;width:33.33%! Dxm-rm-body lipadding-left:15px;width:50%! Dxm-rm-body-col6 li{position:relative;float:left;display:inline-block;box-sizing:border-box;width:16.66%}. Dxm-rm-body-col7 li{padding-left:18px;width:14.28%}. Dxm-rm-body-col8 li{padding-left:1pc;width:12.5%}. Dxm-rm-body-col9 li{padding-left:15px;width:11.11%}. Dxm-rm-body-col10 li{padding-left:14px;width:10%}. Dxm-rm-body-cover:after{display:block;padding-top:100%;background-position:center;background-size:contain;background-repeat:no-repeat;content:”}. Dxm-rm-body-title:after{display:block;display:-webkit-box;overflow:hidden;height:2.8em;white-space:normal;font-size:14px;line-height:1.4em;-webkit-line-clamp:2;-webkit-box-orient:vertical;word-break:break-word;-webkit-hyphens:auto;-ms-hyphens:auto;hyphens:auto}. Dxm-rm-body-attributte{overflow:hidden;height:20px}. Dxm-rm-body-mrsp{margin-left:3px;color:#a0a3a6;text-decoration:line-through;font-size:9pt} /! Content: “you may like”;! Dxm-rm-body > li:nth-child(n+7)! Content: “Portable Pet Dog Pooper Scooper Poper Scooper Poper Scooper Poper Scooper Poper Scooper Plastic Poop Scoop Picker Excreta Cleaner Tool”;! Dxm-rm-body li:nth-child(n+7){display: none;}. Dxm-rm-body-title:after {color: #000000; content: “2500g Electric Dry Food Grinder Machine Grains Spices Hebals Mill Cereal 4000W”;}. Dxm-rm-body-price:after {content: “AUD 378.98″;}. Dxm-rm-body-title:after {color: #000000; content: “Six Channel Chassis ears Automotive Electronic Stethoscope Noise Finder Tool Set”;}. Dxm-rm-body-price:after {content: “AUD 188.99″;}. Dxm-rm-body-title:after {color: #000000; content: “Oil Barrel Crimper Sealer 35mm 70mm 200L Drum Cap Seal Barrel Crimping Tools”;}. Dxm-rm-body-price:after {content: “AUD 94.11″;}. Dxm-rm-body-title:after color: #000000; content: 3\\.

Product Description This Ct125 3-in-1 Micro Multi-function Drilling and Milling Lathe Machine Adopts Cast Iron Body and All Metal Gears. It Is Mainly Used for the Outer Circle, Inner Hole, End Face, Taper and Metric and Inch Thread Processing of Various Rotating Parts. It Is Suitable for Families, Studios, Schools, and Various Small Repair Workshops. Specification Machine Type: Ct125 Power: 180 W Voltage: 110 V Size: 523041 Cm/20.511.5816.14in Wight: 22 Kg Package Size: 553048 Cm/21.711.818.9in. Ct125 Mini Electric Lathe Drilling Milling Machine 3 in 1 Metalworking Equipment. Ct125 3-in-1 Micro Multi-function Drilling and Milling Lathe Machine. This Ct125 3-in-1 Micro Multi-function Drilling and Milling Lathe Machine Adopts Cast Iron Body and All Metal Gears. The Control Panel of the Machine Tool Is Simple and Easy to Operate. The Machine Has High Precision Spindle and Quality Electronic Control System The Bed Saddle Is Easy to Fix Fixtures, Molds, Pliers, and Other Tools. The High-power All-copper Asynchronous Motor Provides Strong Power. Dovetail Rail: the Bed Adopts Dovetail Guide Rail, the Contact Surface Is Larger and More Stable. Three-jaw Chuck: This Machine Has 80mm High Precision Three-jaw Chuck. Drilling and Milling Head: It Can Be Rotated 360°, Raised and Lowered Within a Range of 80mm. Drilling and Milling Gears/Pulleys: Through the V-belt Position, the Drilling and Milling Spindle Can Achieve 10 Kinds Rotate Speed. Compact and Easy to Install. Easy to Operate, No Training Required. This Machine Can Process Various Non-ferrous Metals Such As Titanium, Stainless Steel, Steel, Iron, Aluminum, Copper, and Soft Materials Such As Wood and Nylon. Machine Type: Ct125 Power: 180 W Voltage: 110 V Size: 523041 Cm/20.511.5816.14in Wight: 22 Kg Package Size: 553048 Cm/21.711.818.9in. Maximum Workpiece Rotation Diameter: 125mm/4.9in Maximum Workpiece Length: 180mm/7.1in Maximum Workpiece Rotation Diameter on the Tool Rest: 60mm/2.4in Spindle Through Hole Diameter: 9mm/0.35in Spindle Taper Hole: Mt. 1 Number of Metric Threads Processed: 8 Machining Metric Thread Pitch Range: 0.4-1.5mm/0.02-0.06in Number of Inch Threads Processed: 8 Machining Inch Thread Pitch Range: 0.0028-0.00551 /N Longitudinal Feed Series: 2 Longitudinal Feed of Spindle per Rotary Tool Holder: 0.07-0.14mm/0.003-0.005 Tailstock Sleeve Stroke: 18mm/0.71in Taper Hole of Tailstock Sleeve: Mt. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday.

The tool used for milling machine is a milling cutter. The side and front of the milling cutter are both cutting edges. It has certain dangers, so it must be used under the guidance of professionals. 2, the main parts of the machine: such as the spindle box, long base, short base, large slider, small slider, motor blades, connecting blocks, gears, etc. Are made of metal materials. 1, motor speed: 20000 rev / min (optional 12000 rev / min). Input voltage / current / power /: 12VDC / 2A / 24W. 3, Y, Z axis slider stroke: 30mm, X axis slider stroke: 145mm. 5, the maximum clamping size of the vise: 50mm. 6, the hand wheel has a 0.02mm precision scale line, increasing the accuracy of the machine tool workpiece. Applicable processing: wood, soft metal gold, silver, copper, aluminum, etc. , plexiglass, plastic and so on. 7, accuracy 0.07mm. 1x A set of Milling Machine. 1x Speed Control Adapter.

Material: Aluminum + Plastic. Laser Power: No Laser / 500mW / 2500mW / 5500mW (Optional). Working Area: 30018040mm / 11.87.11.6in. Frame Size: 420355280mm / 16.51411in. Spindle: 775 Spindle Motor (12-36V) 24V: 7000r/min, 36V: 9000r/min. Step Motor: 1.3A / 0.25N. Power Supply: 24V / 5.6A (110V-240V). Engraving Materials: Plastic, Wood, Acrylic, PVC, PCB & Others. Supported Formats: jpg / bmp / png. Communication Port: Micro USB. Package Size: 7500g / 265oz. Package Weight: 442518cm / 17.39.87in. Connect the power supply and connect the USB. Determine your Machine’s COM port. Open grbl Control software.