Now to the listing. VARIABLE SPEED Vertical Bench Type Milling Machine with chip tray, as shown. This machine uses 120V Standard Power! Main Features Of This Machine. Completely different factory, castings, and design than many others out there, GREATLY improved design. Extremely Reliable, Brushless DC Variable Speed Motor Included Standard. Belt Drive Design, For Smoother, Quieter Running. Extra Large Column To Base Mount, Over 400% More Area, Makes A Much More Rigid Machine, Greatly Improved Over Other Machines In This Size Range. 3 Bolt Head to Column Mount is Standard, Also For Increased Rigidity. Runs in both Forward and Reverse, Good for Tapping. Larger Dials at Table Ends, Graduated in. 001, For Easier to Read, Accurate Table Movements. Leadscrews Are True Inch Pitch Screws (Not Metric Conversions Like Many), 10 Threads Per Inch. More Information below under the DESCRIPTION Tab below It is NOT just the same old model with just a belt drive upgrade Be sure to compare carefully. Special Features that set this mill apart from others (BE SURE TO COMPARE THESE DIFFERENCES). Quill DRO Included Standard (This is for the spindle up/down movement). 3 Bolt Head Mount is now standard (where the head mounts to the Z Axis), for more rigidity when milling Much improved over the single bolt mount type. Main Z Axis Column is attached to the base with 4 bolts, and mounted from the top, with a wide, proper mounting surface for much more rigidity over other models in this size range. 001 Readings with larger dials on the X and Y axis, with true 10 Thread Per Inch Leadscrews make it easier to cut accurately One line on the dial is. 001, one full turn of the handwheel is. 100, much easier to use than those with odd metric conversions. Precision ground ways for smoother movements Not just rough milled. Thrust Bearings in leadscrew ends not bushings Much smoother movements and less backlash. Split nuts on X and Y Axis to allow for backlash adjustment. DC BRUSHLESS MOTOR, Variable Speed, POWERFUL, SMOOTH, and RELIABLE Belt Drive from Motor to Spindle runs MUCH quieter than others, and eliminates any failure prone plastic gears (And the hassle of changing them when stripped). Average time delivered is 2-7 days depending on how far from Pittsburgh you are, it could be a little longer in remote places but normally is very fast. Quality Machine Tools, 701 Parkway View Drive, Pittsburgh, PA 15205. We are machinists here too, so we know what we sell. This is really a top quality machine, and will last a long, long time. AND we are here for support too. We sell these machines regularly, we know them inside and out, and have been in business for many years, so if there is any question, we can help. Variable Speed with Belt Drive and Brushless DC Motor. PM25MV (DC Brushless Motor, and Belt Drive Head is Standard). End Milling Capacity 3/4. Face Milling Capacity 2/1/2. Table Size 27-1/2 x 7-1/8. Cross Travel (Y Axis) 7. Longitudinal Travel (X Axis) 19. Table Leadscrew Pitch 10 TPI. Vertical Travel (Z Axis) 13. Max Distance Spindle to Table 13. Taper of Spindle R-8, w/7/16-20 Drawbar Thread. T Slot Size Actual size 12mm, our 1/2 kit listed is sized for this machine. Range of Spindle Speeds 50-2250rpm, 2 Steps. Headstock Tilt Left & Right ±90°. Machine Height (Without Stand) 38-1/2. Net Weight (Not Including Stand) 265 LBS. Net Weight (With Stand) 350 LBS. Power Required 110/120V, Minimum 15 Amp Circuit (Do Not Use Extension Cords). NO extra charge for residential or anything on these, as long as a truck can get to you, its covered. Check out our other auctions for more lathes and mills. The item “PM-25MV BENCH TOP MILLING MACHINE with3-AXIS DRO STAND VARIABLE SPEED SHIPS FREE” is in sale since Tuesday, November 13, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “qualitymachinetools” and is located in Pittsburgh, Pennsylvania. This item can be shipped to United States, Canada.

• MPN: PM-25MV
• Brand: Precision Matthews
• Country//Region of Manufacture: China

Sign up to Newsletters. Power Feed APF-500X Torque for Type Milling Machines 0-210 RPM Feeding Device. You are looking at our new Power Feed X for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. 107T for plastic transmission gear and 6T for motor shaft gear 107 is not divisible by 6, 107 % 6 = 17.8333333333… The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Set the fix stand on work table, set table bearing bushing on the axis screw, then set the power table feed on the fix stand, take out the gear housing. Use one hand to hold the center transmission shaft. Set the bevel gear on axis screw with the other hand. Then check if the backlash between gears is between 0.1-0.2mm. Add shims (1.0t, 0.25t, 0.1t) if the backlash is too large. Repeat step 2-3 until reaching satisfying backlash. Tighten the handle to start setting socket parallel key and bevel gear. Rotate the handle slightly to feel if any interfere occurs in between. If do, please repeat step 3-4 to add more shims. If not, go to next step. Take out the handle, add proper shim (43×33), adjust the backlash between dial & bevel gear and lock with fix ring. Set the handle and tighten, slightly rotate the handle. Normally it should be smooth without any interfere. Finally, set the gear housing and limit switch. Power supply switch and reset switch. The right side of power switch is ON. The left side is OFF. Red light will show when machine is on. The red round button on right side is reset switch. Reset button will jump up to cut off the power if the machine overloads. The operator must reduce cutting load, then press reset switch to continue operating. Feed knob and rapid button. Rotate feed knob after power is on. Turn left for left side feeding and vice versa. The button in the middle is rapid button. Tool will travel rapidly to left side if you keep pressing the button. Release to make power table feed will back to normal speed. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. NOTE: To stop jog operating, you must first turn FEED KNOB TO 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Add an auto power table feed to your milling machine. A simple and inexpensive way to increase productivity. Small volume and easy installation. Excellent speed control in the entire range. Jog function operates at any feed speed. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Package Dimensions: 11713(275175335mm). 1 x X-Axis Fix Stand with Bushing. 1 x Bevel Gear with Fix Ring. 1 x Handle Washer. 2 x Stop Blocks. 2 x Stop Set. 2 x Socket Screws (M8P1.2535). X Socket Screws M8P1.0. 6 x Small Shims. 2 x Small Shims 26.2. 3 x Small Shims 26.2. 4 x Large Shims. 2 x Spring Pins. 1 x Cable Clamp. 1 x User Manual. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “X Axis Power Feed Milling Table Milling Machine Vertical Milling Bridgeport Acer” is in sale since Sunday, July 23, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “bestoffersshopping” and is located in Ontario, California. This item can be shipped to United States, all countries in Europe, Canada, Mexico, Australia.

• Brand: VEVOR
• MPN: ICXCX007
• Model: APF-500X
• Country/Region of Manufacture: CHINA
• Torque: 135lbs
• Weight: 13.2lbs
• Color: White
• Current: 2.8A
• R.P.M.: 0-210
• Package Dimension: 11 x 7 x 13 inch
• UPC: 283961294156

Here is a nice Brown & Sharpe Dividing / Indexing Head. It accepts #4 morse taper. Included is a #4 MT chuck and dead center. The thread for mounting a chuck is 2-1/4 x 4-1/2 TPI. The face plate is 6-3/4″ and the dividing plate is 5″. The center height is a little under 5-3/16 (5.165). Check the pictures for condition as the items we sell are used and may have marks or blemishes. Check out the other items in our store at LnL Deals. The item “Brown & Sharpe Dividing Indexing Head Milling Machinist Tool Index Gear” is in sale since Thursday, November 22, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “lbkos14mvy” and is located in Elizabethtown, Pennsylvania. This item can be shipped to United States.

• Modified Item: No
• Country/Region of Manufacture: United States
• Custom Bundle: No
• Non-Domestic Product: No
• Brand: Brown & Sharpe