BRIDGEPORT Knee Type Vertical Milling Machine Used AM14222. Table: 9″ x 48″. Power Feed on Table Left & Right Y Axis Only. One -Shot Lubrication System. Installation / Maintenance / Operational Manual. 480Volt, 60HZ, 3 Phase. Dust ExtractionFabricating MachinerySawing & CutoffTube & Pipe. This item is on our floor available immediately, subject to prior sale. Do not hesitate to call with any further questions and we look forward to doing business with you. And this sale of these items is on an as-is and without any representations or. Warranties, expressed or implied, of any kind including safety, condition, or quality. Protection of the user or to comply with applicable governmental laws or requirements. And understood that purchaser assumes this responsibility and the above is an integral part of this sale. All sales are F. Cleveland, Ohio unless otherwise specified. The item “Bridgeport Vertical Milling Machine 9 x 48 1.5HP Series 1 Used AM14222″ is in sale since Monday, September 14, 2015. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “allsetmachine” and is located in Cleveland, Ohio. This item can be shipped to United States.

• Brand: Bridgeport

THIS IS A NEWLY REPAIRED VARIABLE SPEED BRIDGEPORT 9″ X 42″ MILLING MACHINE WITH DRO AND BRAND NEW POWER FEED. THIS MILLING MACHINE WAS JUST REPAIRED HERE AT DAN’S MACHINE TOOL, INC. COMES WITH A 2 AXIS (X AND Y) SARGON DRO. HAS A BRAND NEW ALIGN X AXIS POWER FEED. THE TABLE IS TIGHT!!!! HAS A HAND COOLANT PUMP. RUNS ON 220V / 3PH / 1 1/2 HP MOTOR. MACHINE HAS BEEN INSPECTED MECHANICALLY AND ELECTRONICALLY AND IS FREE FROM DEFECTS. ARE YOU LOOKING FOR A PART OR TOOLING FOR YOUR METAL FABRICATION MACHINE? IS YOUR MACHINE NOISY? JUST NEED SOME ADVISE? CALL DAN’S MACHINE TOOL, INC. (714) 666 – 1266. WE SELL MOST BRIDGEPORT MILL PARTS (VARI SPEED & STEP PULLEY). CLOCK/QUILL SPRINGS, HANDLES, BELTS, BEARINGS, KNOBS, HANDWHEELS, SWITCHES, HUBS, PULLEYS, WIPERS, NUTS, BOLTS, DRAWBARS, REPAIR KITS: 1 1/2HP, 2 HP STEP PULLEY AND OR VARI SPEED. IF YOU NEED A HARD TO FIND PART CALL DAN’S MACHINE TOOL, INC. OVER 30 YRS OF REPAIR AND REBUILDING EXPERIENCE ON ALL METAL WORKING MACHINERY INCLUDING BUT NOT LIMITED TO. ACRA, BRIDGEPORT, CINCINNATI, HARDINGE, LAGUN, LE BLOND, KENT, SCOTCHMAN. DAN’S MACHINE TOOL, INC. SPECIALIZES IN REPAIR & REBUILD, NEW & USED TOOLING, SALES OF NEW AND PREOWNED MACHINES, MANY IN STOCK: MILLS, LATHES, GRINDERS, BANDSAWS, IRONWORKERS. The item “NEWLY REPAIRED BRIDGEPORT 9 X 42 MILLING MACHINE” is in sale since Wednesday, September 16, 2015. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “qjen1″ and is located in Anaheim, California. This item can’t be shipped, the buyer must pick up the item.

• Country/Region of Manufacture: United States
• Brand: BRIGEPORT
• Model: VARIABLE SPEED 1 1/2 HP MOTOR / 9″ X 42″

Model: Series I BRIDGEPORT EZ Plus Three-Axis CNC Vertical Milling Machine with Three-Axis Digital Readout, S/N: HDNG 0441 (New 2003). Table working surface Number of t-slots Range: longitudinal (X) cross (Y) vertical, knee quill (Z) Maximum/Minimum distance, spindle nose to table Maximum/Minimum distance, centerline of spindle to face of column Maximum uniform table load Ram travel Head tilt, left and right Head tilt, front to rear, each way Infinitely variable spindle speeds, two ranges Spindle taper Feedrate range X & Y axes manual and automatic positioning rate X & Y axes feedrate range, infinitely variable Minimum feedrate increment. 9″ x 48″ 3 30″ 12″ 16″ 4.5″ 18.25″/2.5″ 18.75″/6.75″ 300 Lbs. 12 90 degrees 45 degrees 60-500 R. /Continuous Duty 3/60/208-220-440 volt spindle drive motor and electrical controls Machine is wired for 220 volt operation. Approximate Weight: 2,400 Lbs. The item “Series I BRIDGEPORT EZ PLUS Three-Axis CNC Vertical Mill With 3X DRO (New 2003)” is in sale since Tuesday, September 15, 2015. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “grandmarshallmachinery” and is located in Hauppauge, New York. This item can be shipped worldwide.

• Brand: BRIDGEPORT
• Model: Series I EZ Plus

Horizontal Vertical 5C tilting indexing milling fixture 24 tooth index. I can’t find a makers name on this fixture, It looks like a Yuasa. Looks like very nice quality, possible that this is what Yuasa copied. The item “Horizontal Vertical 5C tilting indexing milling fixture 24 tooth index” is in sale since Saturday, September 12, 2015. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “metal_shop_tools” and is located in Eugene, Oregon. This item can be shipped to United States.

2001 HAAS TM1 Milling Machine. This machine is hooked up and running and in good condition. It has high speed machining and macros, 12×30 travel, 6000 RPM spindle. The item “HAAS TM1 CNC TOOL ROOM MILL” is in sale since Monday, September 14, 2015. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “grandtraversetool” and is located in Traverse City, Michigan. This item can’t be shipped, the buyer must pick up the item.

• Country/Region of Manufacture: United States
• Brand: HAAS
• Model: TM 1

Bridgeport Series II Special. Year of Manufacture: 2001. This machine is in very good used condition. What we have done to it is as follows. The 58 inch table was removed, reground flat, respotted. A new table gib was fabricated and fit to the new ground table and saddle. A new electric automatic lube pump was installed. All chips were removed under the table and in the saddle. New X and Y lead screws were installed and the back lash was adjusted to approximately. The 2j varispeed head was checked out on our test stand. New bearings were installed on the R8 spindle. The R8 spindle was reground to new specifications. A new varispeed belt was installed. A new upper clutch assembly was installed in the varispeed head and the head is now in excellent running condition. The machine and head were repainted. Table travel (X-Axis) manual. Table travel (X-Axis) power. 11 x 58 in. (279 x 1473 mm). 2 HP (1.5 Kw). 3 HP (2.2 Kw). 7 x 10 ft (2.1 x 3.1 m). The item “Bridgeport Series II Special Vertical Knee Milling Machine” is in sale since Tuesday, September 15, 2015. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “mbnelt” and is located in Stratford, Connecticut. This item can be shipped to United States.

• Country/Region of Manufacture: United States
• Brand: Bridgeport
• Model: Series II

Our stock number: 28836. BRIDGEPORT VERTICAL MILLING MACHINE SERIAL NUMBER: 259142 Year: 1991 GENERAL SPECIFICATIONS Table Size: 9″ x 42″ Longitudinal Travel: 30″ Cross Travel: 12″ Knee Vertical Travel: 16″ Ram Travel: 12″ Quill Travel: 5 Spindle Taper: R-8 Spindle Speeds, Variable: 60 to 4200 RPM Feeds: (3) 1.5, 3, 6 IPR Head Swivel (Right/Left): 90 Degrees Head Tilt (Up/Down): 35 Degrees. EQUIPPED WITH 2 HP Spindle Motor Sony Two Axis Digital Readout Servo Type 100 Power Feed Maxi Torque-Rite Power Draw Bar Chrome Knee Ways One Shot Lube Approximate Weight: 2000 Lbs. Bank Wire Transfers and Checks. Skids shown in pictures are not included with the item. 02 to discuss any trade-ins or items you have available for sale. Located in Cincinnati, Ohio. Is a worldwide dealer in new and pre-owned conventional and CNC Metalworking Machinery. In addition to Machinery and Equipment Sales, C. Woods Machinery Moving Division has the capacity to move a single piece of equipment or entire facility! The item “BRIDGEPORT VERTICAL MILLING MACHINE SERIES I DRO (28836)” is in sale since Sunday, September 13, 2015. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “buyusedcheaper” and is located in Cincinnati, Ohio. This item can be shipped to United States.

• Brand: Bridgeport
• Model: Series I

Our stock number: 28576. BRIDGEPORT VERTICAL MILLING MACHINE MODEL: Series I SERIAL NUMBER: BR-255242 Year: 1990 GENERAL SPECIFICATIONS Table Size: 9″ x 42″ Longitudinal Travel: 30″ Cross Travel: 12″ Knee Vertical Travel: 16″ Ram Travel: 12″ Quill Travel: 5 Spindle Taper: R-8 Spindle Speeds, Variable: 60 to 4200 RPM Feeds: (3) 1.5, 3, 6 IPR Head Swivel (Right/Left): 90 Degrees Head Tilt (Up/Down): 35 Degrees. 2 HP Spindle Motor, 220/440/60/3 NEW (13) Piece Set R-8 Collets NEW (52) Piece Clamping Set Chrome Knee Ways One Shot Lube 6 Bridgeport Vise w/Swivel Base NEW Acu-Rite 200S Two Axis Digital Readout. Approximate Weight: 2000 Lbs. Bank Wire Transfers and Checks. Skids shown in pictures are not included with the item. 02 to discuss any trade-ins or items you have available for sale. Located in Cincinnati, Ohio. Is a worldwide dealer in new and pre-owned conventional and CNC Metalworking Machinery. In addition to Machinery and Equipment Sales, C. Woods Machinery Moving Division has the capacity to move a single piece of equipment or entire facility! The item “BRIDGEPORT VERTICAL MILLING MACHINE SERIES I With New DRO (28576)” is in sale since Saturday, September 12, 2015. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “buyusedcheaper” and is located in Cincinnati, Ohio. This item can be shipped to United States.

• Brand: Bridgeport
• Model: Series I

Bolton Tools Gear Driven Milling Machine. Motor: 2 HP, 110V/220V, single-phase, 1720 RPM. Face mill capacity: 3. End mill capacity: 3/4. Distance spindle to table: 17-5/16. Number of speeds: 6. Spindle speeds: 60HZ: 95,175,310,450,850,1500 RPM. Head tilt left and right: ±90°. Table size: 9-1/2″ x 32″. Table travel (longitudinal): 20-1/2. Table travel (cross): 9. T-slots: 4 at 2-1/8″ centers, 5/8″ wide. Overall dimensions: 47″ L x 32″ W x 55 H. Bolton machines have been on the market for over 4 years. The customer response has been tremendous! People are very happy with our machine quality and price point. We offer some of the best prices in the country, we guarantee it! We are committed to our products and our customers. We would love for you to give us a call to discuss any of your machining needs. BOLTON TOOLS IS LOCATED IN City of Industry, CA. SHOW ROOM IS AVAILABLE! Our goal is to keep a 5-STAR rating in all categories. If you have any questions regarding our products or services, please give us a chance for correction. Please do not leave a negative or neutral feedback. We will do our best to fix it. We care about our customers, and we strive to bring you the best customer experience ever. You will receive a response within 24 hours. Feed Back: If you are considering leaving negative or neutral feedback, please give us the opportunity to resolve the issue first. If you have any questions, click “Ask a Question” at the bottom of this page. The item “Bolton Tools Milling Machine 9 1/2 x 32 Power Feed 2 Axis DRO ZA45PD” is in sale since Tuesday, July 02, 2013. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “boltontools” and is located in Rowland Heights, California. This item can be shipped to United States, to Canada.

• Brand: Bolton Tools
• Model: ZA45PD
• MPN: ZA45PD

CARBOLOY INDEXABLE T SLOT CUTTER 5/8 X 1 1/2. Size : 5X8 X 1 1/2. The item “CARBOLOY INDEXABLE T SLOT CUTTER 5/8 X 1 1/2″ is in sale since Tuesday, September 08, 2015. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “randc_inc” and is located in El Monte, California. This item can be shipped to United States.