Sign up to Newsletters. X-Axis Power Feed 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage: 110 V, 60 Hz. Rotate speed: 0-200 rpm. Length: 33 cm (13 inch). Width: 20 cm (7.9 inch). Height: 18 cm (7 inch). Gross weight: 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “ALSGS 110V 220V Power Feed for Vertical Milling Machine X Y Axis AL-310SX” is in sale since Wednesday, October 18, 2017. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “world-etrade” and is located in Ontario, California. This item can be shipped to United States, Canada, Mexico, Germany.

• Brand: VEVOR
• MPN: 3fgdg00311
• Bundle Listing: Yes
• Model: AS-250-150
• Country/Region of Manufacture: CHINA
• RPM: 0~200
• TORQUE: 150LBS
• Type: X-axis
• VOLTAGE: 110 V, 60 Hz
• Gross weight: 6.5 kg(14.3 lb
• UPC: 895800908584

BROWN & SHARPE #000 PLAIN HORIZONTAL MILL. – 8″ X 26″ TABLE. – WGT: 1,245lbs. SUBJECT TO PRIOR SALE. “Please call De or John with any questions”. The item “BROWN & SHARPE #000 PLAIN HORIZONTAL MILL” is in sale since Tuesday, July 18, 2017. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “mckean2002″ and is located in Brook Park, Ohio. This item can be shipped to United States.

HOIKE 2HP VERTICAL MILL. – RAPIND X TRAVEL. – TABLE: 10″FB X 44″LR. – DIM: 60″FB X 60″LR X 84T. – WGT: 2,250lbs. SUBJECT TO PRIOR SALE. For more information call: De or John. The item “HOIKE 2HP VERTICAL MILL” is in sale since Wednesday, July 12, 2017. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “mckean2002″ and is located in Brook Park, Ohio. This item can be shipped to United States.

BRIDGEPORT TORQ CUT 22 CNC MILLING MACHINE. (Bridgeport Machine Spec’s). Wired for 208/230 now/460v 3phase. 5hp ac spindle motor. 22 tool BT40 automatic tool change 7.5sec. Sliding head on a column fixed to a base carrying a compound table arrangment with a load capacity of 750lbs. 472 ipm rapid traverse on x and y. 300 ipm rapid on z. +/. 00025 positioning accuracy in all 3 axis. +/. 00015 repeatability in all 3 axis. Flood coolant system with 3 jets at the spindle. Automatic one shot centralized lubrication system. Interface for erickson 400lb indexer. Has fourth axis drive. Mach is under power. Come check it out. Machine has been cleaned/repaired and tested. We replaced the y axis ball screw as it was out of spec. We rebuilt computer to orriginal specifications with the addition of a new computer and added sshdd modual. Replaced defective original monitor with flat screen monitor. The item “BRIDGEPORT TORQ CUT 22 CNC MILLING MACHINE” is in sale since Friday, September 15, 2017. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “bg4371″ and is located in Plainville, Connecticut. This item can’t be shipped, the buyer must pick up the item.

• Brand: Bridgeport Torq Cut 22
• MPN: Does Not Apply

Good machine, light usage, mainly used for racing motors, vice included. The item “Brdigeport Mill 9×48 vertical milling machine with spacer for the head” is in sale since Saturday, March 24, 2018. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “jeffspotts65″ and is located in Mentor, Ohio. This item can be shipped to United States.

• Brand: Bridgeport

Clausing 8530 6″x24″ Vertical Milling machine Morse taper 2 Quill. This is the late model with factory riser block and 2 speed table crank. This machine is in good original condition. Everything still is tight and smooth. The dovetails are all in good condition and still show some original machining marks. There is less than half a turn of backlash on all axis about. The table does have some marks but not bad. Please take a look at the pics. The quill fine downfeed does not work and is missing the handwheel. The hand crank for the knee is not original and appears to be a vise handle. The motor is original and runs smooth and quiet, as does the mill. It is 3 phase, 3/4 hp, 1725 rpm. I recently disconnected the motor from a Teco VFD, but can run it for you if you like. Drum switch with forward and reverse. This machine has not been painted and is original paint, as best as I can tell. The finish on the machine is very nice, clean, and smooth. Included with the machine are 6 collets and drawbar, 2 endmill holders, wrenches and allen wrenches, and a couple hold downs. This is really a nice milling machine built in the USA and of very nice quality. Item is for sale locally and is subject to being ended at any time. Clausing vertical and horizontal Millers were manufactured by the Johansson Company, a firm that Atlas/Clausing eventually bought out. The vertical machine was built in two models, the original 8520 and 8525 (that differed only in their quill fittings) and the later and improved 8530; the horizontal miller was designated as the 8540, 8541, 8550 and 8551, again with only relatively minor details (the type of electric motor or the provision of hand or power table feeds) to distinguish between them. A sought-after machine in its home country – and with good reason – the Clausing was a compact, strongly-built machine that could be driven by either a single or three-phase 1725 rpm 60 cycle rear-mounted motor that provided (through an all-V-belt drive system with an intermediate jockey pulley) a range of useful spindle speeds: 180, 350, 600, 1000, 1900 and 3250 rpm. To slow the spindle from higher r. A hand-operated brake was provided.. The hardened, chrome-nickel steel spindle could be ordered with either a No. 2 Morse (Model 8520) or a No. 7 Brown and Sharpe taper (Model 8525) – both perhaps a little undersize for heavier work – while the hard-chrome plated quill, with a micrometer adjustable stop, had 3 of travel by either a (useful and clever) two-speed, quick-feed lever – or a handwheel. Each quill was individually fitted at the production stage, with the housing being honed to fit. Not only could the head carrying the spindle be rotated in a vertical plane but the whole of the turret head also rotated horizontally – allowing great versatility in setting jobs and machining otherwise difficult angles. The 24″ x 6″ table, with 15″ of longitudinal and 5″ of cross movement, carried three T slots, had handles at both ends and large, clearly engraved micrometer dials. The table feed screws were of high quality, having ground threads and supported in ball bearings where they passed through the table-end brackets; options available for the table feed were an hydraulic drive for production work and (though possibly only on the later 8530 model) a hand-operated fast table feed. The latter unit consisted of a gearbox casing hung from the end of the table with a handwheel permanently attached to the lower shaft that connected directly to the reduction gearing. With the handle pushed in the feed screw was driven at a 1:1 ratio but when pulled out a “high-speed” 4 : 1 drive was engaged – where one turn of the handle rotated the feed screw through 4 turns to re-position the table very much more quickly. On the Model 8530 the option was offered of an electronically controlled power feed unit; this could be provided in two forms, to move the table just longitudinally, or in traverse as well – though unfortunately both versions earned a reputation for unreliability. For the size of miller the number and closeness of the gib-strip adjustment screws on both table and knee must be a record – but how much easier it would have been to fit a proper tapered, screw-adjusted, gib “block”. The vertical travel of the table was 11 3/8 “, the clearance between the spindle nose and table top 15 5/8 ” and the throat (from spindle centre to column) 8.5. Supplied as standard with each miller was an electrical reversing switch, collet draw bar, floor cabinet storage shelf, collet storage and chip tray. The overall dimensions were 36 ” deep x 40″ wide x 70 high. However, despite the advantages outlined, the machine was not without its problems – and there are one or two points worth keeping an eye on: the quill down-feed pinion is rather “light” for heavier work and the gears which operate the fine-down feed are also insubstantial – damage to the last gear in this train is not uncommon. On early machines the quill assembly had no return spring – and hence there was nothing to keep it from dropping if the screw that acted as a friction control was allowed to come loose (this is one miller not to use for very heavy-duty drilling with a 6-foot length of tubing slipped over the feed handle). The later and improved version of the miller carried the Model Type 8530 and had, amongst other improvements, a heavier knee with a horizontal base, a column made taller by the inclusion of a distance piece and a two-speed hand-feed to the table.. The item “Clausing 8530 6×24 Vertical Milling machine” is in sale since Saturday, March 24, 2018. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “deandana1″ and is located in Temecula, California. This item can’t be shipped, the buyer must pick up the item.

• Brand: Clausing
• MPN: Does Not Apply
• Model: 8530

LW dividing head, adjustable tail stock, thread protector nut, and dog drive center. I was unable to find the three jaw chuck that had belonged with it. It apears to be in good working order with no known issues. 3 dividing plates included. Actual item pictured, what is in the pictures is what you will receive. The only thing I can tell you is I got this off the internet. My smaller one (6 swing) has B&S 9 taper. Be sure to view our other items for more great tooling finds. The item “LW Chuck Dividing Head and Tailstock Milling Machine Tool” is in sale since Wednesday, April 05, 2017. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “n2b6001″ and is located in Bedford, Massachusetts. This item can be shipped to United States.

• Brand: LW
• Country/Region of Manufacture: United States

You will receive the Shell Mill listed in the title with 6 Inserts and wrench, all new. If u need more we can discount inserts for you. The 2nd and 3rd pictures show some of our inventory of tooling and inserts. Everything is new, never used. We stock different size shanks for threading, cutting, cut-off, boring bars, indexible, drill chucks all new of all style matching inserts such as 11 IR/ER, 16 IR/ER, WNMG, CNMG, TNMG, VNMG, DNMG, TNMG, and etc. Let me know if your looking for any specific tooling that you don’t see. Don’t hesitate to contact me with any questions. Thank you for looking at my listing. The item “Milling Machine R8 Shell Mill Facemill Cutter 3 Dia. With 10 APMT Inserts” is in sale since Thursday, May 18, 2017. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “mattmikes77collectibles-8″ and is located in Bristol, Connecticut. This item can be shipped to United States.

• Brand: H&HYS
• MPN: Does Not Apply
• Model: CNC ZONES

I will pallet it and drop it off NO charge TO Fastnell. The Mill spindle bearings sound a little noise when spun by hand. I tested the motor with a VFD but I did not see the mill run under power. Looks like the is a gear rack missing that operates the saddle up and down the wiring is old and should be redone. This was acquired from a recently closed machine shop. Take a look at my other auctions to see if there is anything else that you might be interested in. The item “Burke No. 4 bench top horizontal milling machine with original motor” is in sale since Tuesday, February 27, 2018. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “dualquad302″ and is located in Paramus, New Jersey. This item can’t be shipped, the buyer must pick up the item.

• Brand: Burke
• MPN: No. 4