2017
X Axis Power Feed Milling Us Stock Bridgeport & Other Knee Mills Fits
Sign up to Newsletters. Power Feed APF-500X Torque for Type Milling Machines 0-210 RPM Feeding Device. You are looking at our new Power Feed X for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. 107T for plastic transmission gear and 6T for motor shaft gear 107 is not divisible by 6, 107 % 6 = 17.8333333333… The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Set the fix stand on work table, set table bearing bushing on the axis screw, then set the power table feed on the fix stand, take out the gear housing. Use one hand to hold the center transmission shaft. Set the bevel gear on axis screw with the other hand. Then check if the backlash between gears is between 0.1-0.2mm. Add shims (1.0t, 0.25t, 0.1t) if the backlash is too large. Repeat step 2-3 until reaching satisfying backlash. Tighten the handle to start setting socket parallel key and bevel gear. Rotate the handle slightly to feel if any interfere occurs in between. If do, please repeat step 3-4 to add more shims. If not, go to next step. Take out the handle, add proper shim (43×33), adjust the backlash between dial & bevel gear and lock with fix ring. Set the handle and tighten, slightly rotate the handle. Normally it should be smooth without any interfere. Finally, set the gear housing and limit switch. Power supply switch and reset switch. The right side of power switch is ON. The left side is OFF. Red light will show when machine is on. The red round button on right side is reset switch. Reset button will jump up to cut off the power if the machine overloads. The operator must reduce cutting load, then press reset switch to continue operating. Feed knob and rapid button. Rotate feed knob after power is on. Turn left for left side feeding and vice versa. The button in the middle is rapid button. Tool will travel rapidly to left side if you keep pressing the button. Release to make power table feed will back to normal speed. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. NOTE: To stop jog operating, you must first turn FEED KNOB TO 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Add an auto power table feed to your milling machine. A simple and inexpensive way to increase productivity. Small volume and easy installation. Excellent speed control in the entire range. Jog function operates at any feed speed. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Package Dimensions: 11713(275175335mm). 1 x X-Axis Fix Stand with Bushing. 1 x Bevel Gear with Fix Ring. 1 x Handle Washer. 2 x Stop Blocks. 2 x Stop Set. 2 x Socket Screws (M8P1.2535). X Socket Screws M8P1.0. 6 x Small Shims. 2 x Small Shims 26.2. 3 x Small Shims 26.2. 4 x Large Shims. 2 x Spring Pins. 1 x Cable Clamp. 1 x User Manual. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “X AXIS POWER FEED MILLING US STOCK BRIDGEPORT & OTHER KNEE MILLS FITS” is in sale since Saturday, December 17, 2016. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “happykisssoul” and is located in Ontario, California. This item can be shipped to United States, all countries in Europe, Australia.
- Brand: Vevor
- MPN: Does Not Apply
- Model: APF-500X
- Torque: 150lbs
- Weight: 13.2lbs
- Color: White
- Current: 2.8A
- R.P.M.: 0-210
- Package Dimension: 11 x 7 x 13 inch
Comments Off
