X-Axis Power Feed Kit. 0-200 RPM Rotate Speed & 450 in-lb Torque & 650 mm/min Rate. Our feed kit features a robust shell and precise components. It works efficiently on a milling machine with a 5/8 shaft end. Besides, it is designed with buttons and knobs for simple operation. Our milling machine is an excellent choice for meeting the needs of all your milling operations. Take control of your operations and get quality equipment from a name you can trust, VEVOR. High Efficiency & Precision. Low Noise & Easy Operation. Tough Equipment & Tools, Pay Less. VEVOR is a leading brand that specializes in equipment and tools. Along with thousands of motivated employees, VEVOR is dedicated to providing our customers with tough equipment & tools at incredibly low prices. The feed can work automatically or manually by pressing the speed control. And the circuit breaker protects the transmission gear and electronic components. The milling machine table power feed is composed of rugged aluminum. Its finish has been polished to make its surface corrosion-resistant and wear-resistant. The power feed for the mill adopts spiral bevel gears to move freely and quietly on the mill. Most mills are loud, but our mill reduces noise, even in the garage. The mill power feed is fitted out with precise bearings that ensure smooth and stable movement. Less vibration and strain enhance the efficiency of the milling machine. The power feed for the milling machine is easy to install and operate. Only a little maintenance is required to ensure consistent long-term running. The cutter feeder is an indispensable collocation for milling machines. It is suitable for rocker milling machines, drilling and boring machine, and small grinders. Voltage: 110V, 50/60 Hz. Rotate Speed: 0-200 RPM. Max Torque: 450 in-lb. Max Feed Rate: 650 mm/min. Max Return Speed: 850 mm/min. Item Weight: 16.5 lbs / 7.5 kg. Item Dimensions(L x W x H) : 6.5 x 4.5 x 13 in / 16.5 x 11.4 x 33 cm. 1 x Power Feed for Milling Machine. 8 x Adjustable Pads. 2 x Travel Stop Assemblies. 1 x Bevel Gear. 1 x Dial Nut. 1 x Locking Nut. 1 x Product Manual. X-Axis Power Feed: The X-Axis power table feed is made of sturdy aluminum material. It is also designed with a handle, buttons, and knobs for simple operation. Revolution Speed: 0-200 RPM. High quality and efficiency to handle all your milling needs. Long Service Life: The power feed for the milling machine features a smooth and strengthened polished surface, which is waterproof, dustproof, and oilproof. That ensures a long service life in harsh working conditions. High Efficiency & Precision: The x-axis power feed is equipped with spiral bevel gears for rapid control. There are bearings to achieve high efficiency and precision as well. Low Noise & Easy Operation: The milling machine power feed features 9 levels of moving speeds, set by the rotary knob on the side. Moreover, it makes little noise when used, an essential piece of equipment for every workshop. Wide Compatibility: This milling table power feed fits multiple vertical knee-type mills with the same mounting pattern and a 5/8 diameter shaft on the end. Such as Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, etc. Power Feed Milling Machine. 450 lbs / 204 kg. 150 lbs / 68 kg. 135 lbs / 155 kg. 0 – 200 RPM. 0 – 210 RPM. 16.5 lbs / 7.5 kg. 14.3 lbs / 6.5 kg. 13.2 lbs / 6 kg. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. Please be aware that. Please DO NOT fill in the PO Box address. California Warehouse: City of Industry, CA. New York State Warehouse: Perth Amboy, NJ. Georgia Warehouse: Austell, GA. North Carolina Warehouse: Grove NC. Oregon Warehouse: AIRPORT WAY Portland, OR. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. CA & TX & NJ & GA & NC &OR WAREHOUSE. All emails will be responded to within 12-24 hours. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “wulitaotaoh_9″ and is located in this country: US. This item can be shipped to United States, Canada, Germany.

• Brand: VEVOR
• MPN: AL-310SXCZDQ00000
• Model: AL-310S
• Power Source: Electric
• Voltage: 110V, 50/60 Hz
• Control: Manual
• Function: Milling
• Machine Type: Milling Machine
• Max Spindle Speed (RPM): 200 RPM
• Type: X Traverse
• Rotate Speed: 0-200 RPM
• Max Torque: 450 in-lb
• Max Feed Rate: 650 mm/min
• Max Return Speed: 850 mm/min
• Item Weight: 16.5 lbs / 7.5 kg
• Item Dimensions(L x W x H): 6.5 x 4.5 x 13 in / 16.5 x 11.4 x 33 cm
• UPC: 800000893318

Sign up to Newsletters. Brand New AL-310S X-Axis Power Feed Kit For Milling Machine. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AL-310S X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). To stop jog operating, you must first turn FEED KNOB to 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Brand new power feed. X traverse (left-right travel). Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Rotate speed: 0-200 RPM. Max torque: 450 in-lb. Max feed rate: 650mm/min. Max return speed: 850mm/min. Dimension: 8 x 4.5 x 13 inches. Package size: 11.8 x 8.7 x 13.8 inches. Gross weight: 16.5 lbs. 1 x Power Feed For Milling Machine. 8 x Adjustable Pad. 2 x Tiavel Stop Assembly. 1 x Bevel Gear. 1 x Dial Nut. 1 x Locking Nut. 1 x Product Manual. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. Caifornia Warehouse: 18501 Arenth Ave, City of Indus-try, CA 91748. 300 W Airtex Blvd, Suite 200, Houston, TX 77090. 2125 Gateway Blvd, Hebron, KY 41048. 1000 High Street, Perth Amboy, NJ 08861. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “SHARPS X AXIS POWER FEED BRIDGEPORT MILLING MACHINE POWER FEEDER NEW” is in sale since Tuesday, May 15, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “dairuirui122_3″ and is located in Ontario, California. This item can be shipped to United States, Canada, Mexico, Germany.

• Brand: VEVOR
• MPN: ICXCX007
• Bundle Listing: Yes
• Model: AL-310S
• Country/Region of Manufacture: CHINA
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Max torque: 450 in-lb
• Max feed rate: 650mm/min
• Max return speed: 850mm/min
• Dimension: 8 x 4.5 x 13 inches
• Gross weight: 16.5 lbs

Brand New AL-310S X-Axis Power Feed Kit For Milling Machine. Our Brand New AL-310S X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). To stop jog operating, you must first turn FEED KNOB to 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Brand new power feed. X traverse (left-right travel). Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Rotate speed: 0-200 RPM. Max torque: 450 in-lb. Max feed rate: 650mm/min. Max return speed: 850mm/min. Dimension: 8 x 4.5 x 13 inches. Package size: 11.8 x 8.7 x 13.8 inches. Gross weight: 16.5 lbs. 1 x Power Feed For Milling Machine. 8 x Adjustable Pad. 2 x Tiavel Stop Assembly. 1 x Bevel Gear. 1 x Dial Nut. 1 x Locking Nut. 1 x Product Manual. Sign up to newsletter. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “SHARPS X AXIS POWER FEED BRIDGEPORT MILLING MACHINE POWER FEEDER NEW” is in sale since Monday, November 13, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “bilibusyeasy_4″ and is located in Ontario, California. This item can be shipped to United States, Canada, Mexico, Germany.

• Brand: VEVOR
• MPN: GTLPW002
• Bundle Listing: Yes
• Model: AL-310S
• Country/Region of Manufacture: CHINA
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Max torque: 450 in-lb
• Max feed rate: 650mm/min
• Max return speed: 850mm/min
• Dimension: 8 x 4.5 x 13 inches
• Gross weight: 16.5 lbs

Better price, Top Quality, expert Service support. Live demo of multiple products. Owned and operated company. AL-310S X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8in Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed adjust knob Speed can be adjust according to operator’s requirement, ranging from 0-9. Jog switch Normally, jog switch should be at FEED position. For jog movement, just switch to 0 position. Kept holding the switch until it travels to requires position. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). To stop jog operating, you must first turn “FEED KNOB” to “0″(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Type : X traverse (Left-Right Travel). Rotate speed : 0-200 RPM. Max torque : 450 in-lb. Max feed rate : 650mm/min. Max return speed : 850mm/min. Dimension : 7 x 4.7 x 12.6 inches. Gross weight : 16.5 lbs. Brand new power feed. X traverse (left-right travel). Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Power Feed For Milling Machine X 1. Adjustable Pad X 8. Tiavel Stop Assembly X 2. Bevel Gear X 1. Dial Nut X 1. Locking Nut X 1. Product Manual X 1. All items are dispatched from our warehouse in Azusa, CA. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. We never want our customers to wait for parts, we have plenty of parts available for every product. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. The item “SHARPS X AXIS POWER FEED BRIDGEPORT MILLING MACHINE POWER FEEDER NEW” is in sale since Tuesday, July 24, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “ac-racing” and is located in Hacienda Heights, California. This item can be shipped to United States.

• Brand: AC-RACING
• Model: AL-310S
• MPN: ZY8LX00363
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Max torque: 450 in-lb
• Max feed rate: 650mm/min
• Max return speed: 850mm/min
• Dimension: 8″ x 4.5″ x 13″
• Gross weight: 16.5 lbs

Sign up to Newsletters. Brand New AL-310S X-Axis Power Feed Kit For Milling Machine. Our Brand New AL-310S X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). To stop jog operating, you must first turn FEED KNOB to 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Brand new power feed. X traverse (left-right travel). Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Rotate speed: 0-200 RPM. Max torque: 450 in-lb. Max feed rate: 650mm/min. Max return speed: 850mm/min. Dimension: 8 x 4.5 x 13 inches. Package size: 11.8 x 8.7 x 13.8 inches. Gross weight: 16.5 lbs. 1 x Power Feed For Milling Machine. 8 x Adjustable Pad. 2 x Tiavel Stop Assembly. 1 x Bevel Gear. 1 x Dial Nut. 1 x Locking Nut. 1 x Product Manual. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “SHARPS X AXIS POWER FEED BRIDGEPORT MILLING MACHINE POWER FEEDER NEW” is in sale since Monday, April 2, 2018. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “beautysupplyworld” and is located in Ontario, California. This item can be shipped to United States, Canada, Germany.

• Brand: Vevor espesartita
• MPN: FRCXZ00655
• Bundle Listing: Yes
• Model: AL-310S
• Country/Region of Manufacture: CHINA
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Max torque: 450 in-lb
• Max feed rate: 650mm/min
• Max return speed: 850mm/min
• Dimension: 8 x 4.5 x 13 inches
• Gross weight: 16.5 lbs

Sign up to Newsletters. Brand New AL-310S X-Axis Power Feed Kit For Milling Machine. Our Brand New AL-310S X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). To stop jog operating, you must first turn FEED KNOB to 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Brand new power feed. X traverse (left-right travel). Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Rotate speed: 0-200 RPM. Max torque: 450 in-lb. Max feed rate: 650mm/min. Max return speed: 850mm/min. Dimension: 8 x 4.5 x 13 inches. Package size: 11.8 x 8.7 x 13.8 inches. Gross weight: 16.5 lbs. 1 x Power Feed For Milling Machine. 8 x Adjustable Pad. 2 x Tiavel Stop Assembly. 1 x Bevel Gear. 1 x Dial Nut. 1 x Locking Nut. 1 x Product Manual. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “SHARPS X AXIS POWER FEED BRIDGEPORT MILLING MACHINE POWER FEEDER NEW” is in sale since Monday, November 13, 2017. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “qiannlan-3″ and is located in Ontario, California. This item can be shipped to United States, Canada, Germany.

• Brand: VEVOR
• MPN: ICXCX004
• Bundle Listing: Yes
• Model: AL-310S
• Country/Region of Manufacture: CHINA
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Max torque: 450 in-lb
• Max feed rate: 650mm/min
• Max return speed: 850mm/min
• Dimension: 8 x 4.5 x 13 inches
• Gross weight: 16.5 lbs

You are looking at a new X Axis Power Feed for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First, and many, many more. As long as it is the Bridgeport Type Machine, it should fit. This set includes everything you should need to install this power feed, including the power feed unit, table mounting bracket, drive gear, shims, safety stop, and hardware. SHARPS X AXIS POWER FEED BRIDGEPORT MILLING MACHINE POWER FEEDER NEW. These use 110V, Single Phase Power, just a standard 110/120V outlet is needed. Size: 74mm x 87mm x 26.8mm. Power: AC 110V 50/60Hz. 1 x Milling machine power feeder. Be applied to your order immediately. Please be attentions, this service is more recommended for Mondy to Thursday orders. Orders on Friday may be processed on following Monday by UPS, according to UPS’s policy. Used items will not be accepted for return. Our working time: (GMT +8) 9:0018:00. We appreciate your business and strived to improve our customer service and our commitment to quality. Work with you to have it resolved. The item “SHARPS X AXIS POWER FEED BRIDGEPORT MILLING MACHINE POWER FEEDER NEW” is in sale since Sunday, February 05, 2017. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “ka-floor” and is located in CA,KY. This item can be shipped to United States.

• Brand: Unbranded/Generic
• MPN: KR-A-0226
• UPC: Does not apply