Bridgeport 12/BR w/ 1 HP 3 phase 220/440 volt motor. Step pulley J head with working quill power feed and R8 Spindle. 9 x 42 table with working gear box power feed for x axis. Power feed motor is 220v 3 phase. Bridgeport vise w soft jaws. New Fafnir motor bearings. New Timken spindle pulley hub bearings. New Nachi low gear drive shaft bearings. Original Fafnir splined gear hub bearings unshielded (perfect condition, change not needed). Recently replaced SKF Germany matched pair abec 7 lower spindle bearings with correct preload. New Fafnir upper spindle bearing. Spindle bearings are unshielded for total loss oil lube system. Spindle bore run out is. Spindle exterior is perfect. No dings, gouges or marks. New spindle pulley brake. New felt oil filter washer. New feed trip lever. New reverse trip ball lever. New felt way wipers and covers. New bull gear oiler. Excellent quill, no gouges, scoring or wear marks. Just a few small minor dings. Smooth easy quill travel. Ram and turret have smooth easy travel. Now for the bad, and its totally subjective. Table has an average amount of drill and mill marks on its surface. Some filled with epoxy. Its not pristine but I have seen much worse. There are also some tapped holes for hold down studs. X axis movement is smooth. There is wear in the x lead screw with a backlash of. 025 in the center and. 010 at the ends of table travel. The y axis is also smooth however there is some wear in the saddle and knee ways at midpoint of travel but its not horrible and doesn’t make the machine unusable for moderate precision work and can be controlled by adjusting the saddle lock while milling. Y screw backlash is. 003 at the ends and. 018 in the center. If you are looking for a super precise machine over the entire X Y table travel, or want to make parts for NASA, this one is not for you. You should be looking at machines 5K and up. This machine is priced accordingly to its accuracy, usability, and level of restoration. I have tried to give an honest assessment as to not waste your time and ask you not to waste mine with low-ball offers. Once it leaves my shop, you own it. I can load machine onto your truck or trailer with my forklift at no charge. Thanks for looking and good luck. The item “Bridgeport Milling Machine” is in sale since Tuesday, January 29, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “mikeg718″ and is located in Deer Park, New York. This item can’t be shipped, the buyer must pick up the item.

Please call with any questions. We will assist you in any reasonable way to help get your items to your destination, All checks subject to bank verification. Please Call two zero three, five nine two, eight four zero two with any questions or concerns, Thank You! You are welcome to inspect any machine by appointment. Guerrera Machine Company, LLC. Will not be held liable for any inaccurate information. The item “Bridgeport Milling Machine 36 Table, Power Feed” is in sale since Monday, December 17, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “guerreramachinecompanyllc” and is located in Watertown, Connecticut. This item can be shipped to United States.

“MAKE YOUR BEST OFFER”. CNC HORIZONTAL MACHINING CENTER (2) HAAS HS-1 , 15 PALLETS, 20 HP, 12,000 RPM’S , DIRECT DRIVE SPINDLE, CAT 40 and more. With the following approximate specifications and additional equipment. Specifications for the 1997and 2001 Haas HS-1. Pallet Size: 15.8 x 15.8. Pallet Indexing: 0.001 Contouring. Change Time (Pallet): 8 Seconds. Max Pallet Load: 1,000 LBS. Number of Pallets: 2. X Axis Travel: 20. Y Axis Travel: 20. Z Axis Travel: 20. Rapid Rates: 1,000 IPM. Feed Cut: 500 IPM. Spindle Motor: 20 HP. Speed (Spindle): 12,000 RPM. Spindle Taper: CAT 40. Tool to Tool: 2.8 Seconds. Machine Weight: 21,000 LBS. Inline Direct Drive Spindle. 24 Pocket Tool Changer. CONDITION: GOOD USED CONDITION. MANUFACTURED 2001 & 1997. LOCATION: SOUTHWESTERN, OHIO UNDER POWER FOR INSPECTION. THIS ITEM IS CONSIDERED TO BE IN A GOOD USED CONDITION AND YOU CAN SEARCH SELLERS STORE jona-heath TOP RIGHT CORNER OF LISTING TO SECURE ADDITIONAL PHOTO’S, VIDEO OR OTHER INFO. THANK FOR FOR YOUR INTEREST. “Feedback and About Us”. Where you will find that we. For more expensive ITEMS acomodations can be made WITH PRIOR PERMISSION to pay with Pay Pal. We additionally accept personal, company, certified, cashiers checks drawn on recognizable U. Banks and accept bank wire transfers. Due to Homeland Security Regulations. We thank you in advance for your interest in this item and should you have any questions please feel free to ask them of us and we will try to answer them. The item “CNC HORIZONTAL MACHINING CENTER HAAS HS-1 12,000 RPM 2 PALLET 20 HP CAT 40″ is in sale since Monday, December 17, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “jona-heath” and is located in Dover, Kentucky. This item can be shipped to United States.

• Model: HS-1
• Country/Region of Manufacture: United States
• MPN: Does Not Apply
• Brand: Haas