AS-250 150Lbs Torque Power Feed Milling Machine X-Axis ALSGS 0-200RPM. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage: 110 V, 60 Hz. Rotate speed: 0-200 rpm. Length: 33 cm (13 inch). Width: 20 cm (7.9 inch). Height: 18 cm (7 inch). Gross weight: 6.5 kg(14.3 lb). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. AS-250-150 X-Axis Power Feed for Milling Machine. Set of Necessary Accessories. If you have a problem with the product. We will require a picture of the damaged part for verification. All items are dispatched from our warehouse in HACIENDA HEIGHTS, CA. Some products may be dispatched in more than one carton. International Buyers – Please Note. The item “Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM” is in sale since Saturday, March 2, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “zbondfactory-1″ and is located in Hacienda Heights, California. This item can be shipped to United States.

• Brand: ZBOND
• Model: AS-250
• MPN: ZY8LX00361
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″

F4 Aciera Mill swiss- made includes horizontal over-arm. Travel: X = 31.5 inches. Y = 10 inches. Z estimate is 12 inches. 220 volt single phase converted. Variable belt spindle speed. The item “F4 Aciera Universal Mill. Swiss-made. Includes horizontal over-arm” is in sale since Sunday, April 28, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “yax-51″ and is located in McKeesport, Pennsylvania. This item can be shipped to United States.

• Brand: Aciera
• Model: F4
• Country/Region of Manufacture: Switzerland

TAS IRON LTD OFFERS AN OUTSTANDING VERTICAL MILL CONTROL, THIS CONTROL HAS FEATURES LIKE RPM READOUT, FORWARD AND REVERSE, ELECTRONIC BRAKING, 4 PRESET SPEEDS THAT IS REMEMBERED FOR DIFFERENT TOOL SETUPS, MAIN SPEED CONTROL FROM ZERO TO TOP SPEED WITHOUT STOPPING. BRIDGEPORT 2J HEADS ARE GUTTED AND ALL THOS WEARABLE PARTS ARE REMOVED CREATING A VERY RELIABLE AND QUIET RUNNING HEAD. FOR HEAVIER PRODUCTIONS WE CAN INCREASE THE HORSE POWER IF REQUESTED. CURRENT STANDARD MODEL IS UP TO 3 HP. THIS CONTROL CAN RUN ON SINGLE PHASE OR THREE POWER. OFFERS A TAPPING MODE WITHOUT AUTOMATIC REVERSIBLE SPINDLE. THIS CONTROL IS AVAILABLE IN THE LATHE DESIGN AS WELL. YOUR LATHE CAN BE SET TO MAKE TURNING ROUTINES WITH CONTINUING AN AUTOMATIC REVERSAL MOVE TO TAKE ANOTHER CUT OR TOP SET UP THREADING. HORSE POWER FOR THE LATHE STYLE CAN ONLY GO TO 7.5 HP FOR ADDITIONAL COST AT SINGLE PHASE. BUT ON THREE PHASE WE DON’T HAVE RESTRICTIONS AND COST WITH BE DETERMINED BY HORSE POWER REQUESTED. The item “VERTICAL MILLING MACHINE CONTROL SYSTEM, FOR BRIDGEPORT, ACRA, ACER, SHARP” is in sale since Sunday, July 22, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “tasironltd2012″ and is located in Berea, Ohio. This item can’t be shipped, the buyer must pick up the item.

• Model: ELSR CONTROL
• Country/Region of Manufacture: United States
• Brand: TAS IRON LTD

USED REVOLUTION MINUTEMAN III CNC BED MIL with the Centroid CNC Control. Table Size: 12 x 54. X Axis Travel 39. Y Axis Travel 18. Z Axis Travel 20. Spindle Speeds Infinite: 60-4200 RPM. Quill Travel: 5.80. 40 Taper with Power Drawbar. 5 HP Spindle Drive Motor. Fully Programmable Spindle Speeds. Advanced Machinery Resources Inc. Specifications subject to purchaser verification. Orders are not processed until theyre paid in full. The item “Revolution 3 Axis CNC Bed Mill with Centroid Control Bedmill Milling Machine” is in sale since Friday, December 8, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “jerry7oai” and is located in Vancouver, Washington. This item can be shipped to United States.

Welcome to Select Machine Tool. BRIDGEPORT SERIES 2 SPECIAL VERTICAL MILLING MACHINE. TABLE SIZE 11″ X 58″. SPINDLE MOTOR 2 H. SUPPLY VOLTAGE 230/460 VOLT. WEIGHT APPROX 5000 LBS. BIJUR MANUAL LUBE PUMP. BIJUR SPRAYMIST COOLANT UNIT. NEWALL TOPAZ 2 AXIS DRO X&Y AXIS. POWER FEED ON X AXIS. THE ABOVE SPECIFICATIONS ARE DEEMED ACCURATE BUT ARE SUBJECT TO VERIFICATION. We want you to be happy and we also want to help you in any way possible. We want to build relationships with our customers and the best way to do that is by providing quality products, honest representations, value, and service. Again, we want to thank you for your time and interest and we look forward to earning your business in the near future. In order for this to be an enjoyable experience, please ask all questions before purchasing. Thank You for stopping by and please view our other items. FOR ALL OF YOUR AIR, TOOLING, AND MACHINING NEEDS PLEASE VISIT. The item “BRIDGEPORT SERIES 2 SPECIAL 11” X 58” VERTICAL MILLING MACHINE” is in sale since Wednesday, March 27, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “selectmachine” and is located in Roanoke, Virginia. This item can’t be shipped, the buyer must pick up the item.

• Model: SERIES 2 SPECIAL
• Modified Item: No
• Country/Region of Manufacture: United States
• Custom Bundle: No
• MPN: Does Not Apply
• Brand: Bridgeport

We are pleased to offer the following for your consideration. X axis travel 30 (760 mm). Y axis travel 16 (405 mm). Z axis travel 26 (510 mm). Table size 45″ x 16″ (1150 mm x 405 mm). Allowable table load 1500 lbs. SPINDLE: Spindle gage line to table distance 4″-24″ (100-610 mm). Column to spindle center 15.5 (395 mm). Spindle taper ISO No. Spindle speed (Std) 10,000 RPM Spindle speed. AC spindle motor (Std) 18/12 HP (13/9 kW). Spindle torque (Std w/10,000 RPM) 65 ft-lbs 88 N. The only way we can communicate with you is through the. Encourages first-hand inspection of all used machinery. That is UNDER POWER and Available for Inspection. Please verify all of the specs listed for this machine. Expressed or implied these specs to be accurate. The item “2007 Milltronics VM16″ is in sale since Monday, November 19, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “revelationmachinery” and is located in Kansas City, Missouri. This item can be shipped to United States.

• Brand: Milltronics
• Model: VM16IL

GRIZZLY KNEE TYPE MILLING MACHINE- Model G1008. This very fine condition Knee Type milling machine, serial number O-7740 was received in trade from its second owner. The machine shows little if any wear, has been well cared for and is fully functional in all aspects, except the little coolant pump which failed just about immediately. The machine is currently wired for 240 V AC, and is easily reconnected for 120. The machine is available for inspection in Orange Park, Florida, will be loaded at no charge on buyers conveyance at its present location. Crating will be at normal shop rates. This machine weighs around 1000 pounds. Having gotten all this listing done, seems that the computer running this gig is smarter than those of us actually using it… Hence the buyitnow price is a bit higher than that which will work… Something about 30percent of something.. The item “GRIZZLY KNEE TYPE MILLING MACHINE- Model G1008 (a baby Bridgeport)” is in sale since Tuesday, April 30, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “excellence101″ and is located in Fleming Island, Florida. This item can be shipped to United States.

• Brand: Grizzly
• Model: G1008
• Modified Item: No

SPINDLE PULLEY HUB FOR THE STEP PULLEY. THIS WILL FIT THE AMERICAN MADE STEP PULLEY BRIDGEPORT. SEE THE OTHER QUALITY BRIDGEPORT PRODUCTS IN OUR STORE INCLUDING. REPAIR KITS, REPLACEMENT PULLEYS AND CLOCK SPRINGS. We guarantee the items are exactly as said in description. Appreciates your business very much. The free listing tool. The item “BRIDGEPORT STEP PULLEY PART, milling machine SPINDLE PULLEY HUB 2193478 M1116″ is in sale since Tuesday, September 18, 2012. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “mataco1″ and is located in Broadview Heights, Ohio. This item can be shipped to North, South, or Latin America, all countries in Europe, Australia.

• Model: 1116
• MPN: 2193478
• Brand: Bridgeport