If it over 950mm, it cost extra. You may contact with us about the extra cost; – Total length:longer 140mm than travel length – Application:Mill machine, Later, cutting machine, dring machine, grinder machine ETC. One inch equals to 25.4mm We offer Scale length, 120mm, 150mm, 200mm, 250mm, 300mm, 350mm, 400mm, 450mm, 500mm, 550mm, 600mm, 650m, 700mm, 750mm, 800mm, 850mm, 900mm and 950mm. One inch equals to 25.4mm. You may choose ANY two scales in the scale lengths above. After making order, pls kindly tell us the travel length!! Readout Counter/Console: Advanced electronic technology and trigonometric function; Multiple memories and zero reference functions; Rugged die cast aluminum case. Input voltage 80-260V, 50HZ-60HZ; Basic Functions: Zero Reset; Preset; Inch/mm Conversation; ABS/INC Coordinate Conversation/200 Groups Coordinate Display; Non-Volatile Memory (data retained in event of power loss); 1/2 Function key; Linear Error Compensation; Sleep Switch; 200 Points Auxiliary Zero; Automatic Recognition and Storage of Scale Zero Reference Point Special function of milling DRO: Smooth R Function; Simple R Function; Bore in Oblique Line; Bore PCD Circle; Simple Calculator; Corner Chamfer Calculation; Inside Outside Profile Function. We are second generation of readouts. It has the mark of DRO II on the panel and it should have the mark of CHFOIC at the back of the readout and on the packaging box. TTL output, 5um/0.0002 resolution, anti-dust, anti-coolant, double-sealing design at IP53 insulation/protection level; Various international quality accreditations including CE certification, ISO9001 certification, JT25/JT26 certification, JT20 certification, JX13 certification. Are our scales well-sealed and protected against dust and coolant? We believe that claiming double sealing by ourselves is not enough at all. We have the IP53 insulation/protection certificate to prove! Are other sellers providing you the internationally recognized certificate? We guarantee that we supply authentic SINPO scales to you. Please look carefully at our photos and check if you have gotten the real SINPO products. Linear Glass Scales Features 1. High Precision linear scale 2. Resolution : 5um (0.005mm) 0.0002 3. Signal : TTL square /wave EIA-442 4. Grating pitch: 0.02mm (50LP/min) 5. Accuracy: ±0.005 mm or 0.0002 (at 20 deg C) 6. Reference marks at interval of 50mm 7. Response Speed: 60m/min or 40ins/sec 8. 2.5 Meter (can lengthen). Need long scales or special scales? We will find a positive answer for you! This is a complete kit. Usually it cost about 35USD-50USD. Thanks for your understanding. If you receive defective item, please kindly notify us within 14 days. The item “2 Axis Digital Readout DRO Kit with Linear Scales for Milling Machine” is in sale since Wednesday, September 12, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “buyfromtzt” and is located in HK. This item can be shipped worldwide.

• MPN: Does Not Apply
• Country/Region of Manufacture: China
• Brand: Unbranded

Have a machine or an entire facility to sell? Turn your surplus into CASH! Bridgeport Series I, 2HP Vertical Milling Machine. Table To Spindle Nose Distance Range. 2.5″ – 18.25″. 90 – 4200 RPM. 60″ x 60″ x 82 High. Bridgeport ID# M-052 – YouTube. If any other information is needed to help you with quoting, please send us a message. Cash, wire transfers, or company checks are welcome and encouraged. This guarantee applies only to machines, which we own. Shall not be responsible for any damages done by truckers, riggers, or other parties. All machine prices include loading unless otherwise stated. Machinery descriptions are intended as a guide only and their accuracy is not guaranteed. There are no warranties which extend beyond the description of the face hereof. Quotations subject to change without notice. It is the buyers and users responsibility to provide proper safety devices, training and equipment to safeguard the operator from harm for any particular use, operation or set up, and to adequately safeguard the machine, or machines, to conform to all Federal, State and Local Government Safety Standards and All Industry Safety Standards. The item “Bridgeport Series I, 2HP Vertical Milling Machine Table 9 x 42, ID# M-052″ is in sale since Friday, April 5, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “energ_machinery” and is located in East Hampton, Connecticut. This item can be shipped to United States.

• Model: Series I
• Brand: Bridgeport
• Engine: 2 HP
• Featured Refinements: Vertical Milling Machine

Power Feed APF-500X Torque for Type Milling Machines 0-210 RPM Feeding Device. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. You are looking at our new Power Feed X for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. 107T for plastic transmission gear and 6T for motor shaft gear 107 is not divisible by 6, 107 % 6 = 17.8333333333… The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Set the fix stand on work table, set table bearing bushing on the axis screw, then set the power table feed on the fix stand, take out the gear housing. Use one hand to hold the center transmission shaft. Set the bevel gear on axis screw with the other hand. Then check if the backlash between gears is between 0.1-0.2mm. Add shims (1.0t, 0.25t, 0.1t) if the backlash is too large. Repeat step 2-3 until reaching satisfying backlash. Tighten the handle to start setting socket parallel key and bevel gear. Rotate the handle slightly to feel if any interfere occurs in between. If do, please repeat step 3-4 to add more shims. If not, go to next step. Take out the handle, add proper shim (43×33), adjust the backlash between dial & bevel gear and lock with fix ring. Set the handle and tighten, slightly rotate the handle. Normally it should be smooth without any interfere. Finally, set the gear housing and limit switch. Power supply switch and reset switch. The right side of power switch is ON. The left side is OFF. Red light will show when machine is on. The red round button on right side is reset switch. Reset button will jump up to cut off the power if the machine overloads. The operator must reduce cutting load, then press reset switch to continue operating. Feed knob and rapid button. Rotate feed knob after power is on. Turn left for left side feeding and vice versa. The button in the middle is rapid button. Tool will travel rapidly to left side if you keep pressing the button. Release to make power table feed will back to normal speed. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. NOTE: To stop jog operating, you must first turn FEED KNOB TO 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Add an auto power table feed to your milling machine. A simple and inexpensive way to increase productivity. Small volume and easy installation. Excellent speed control in the entire range. Jog function operates at any feed speed. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Package Dimensions: 11713(275175335mm). 1 x X-Axis Fix Stand with Bushing. 1 x Bevel Gear with Fix Ring. 1 x Handle Washer. 2 x Stop Blocks. 2 x Stop Set. 2 x Socket Screws (M8P1.2535). X Socket Screws M8P1.0. 6 x Small Shims. 2 x Small Shims 26.2. 3 x Small Shims 26.2. 4 x Large Shims. 2 x Spring Pins. 1 x Cable Clamp. 1 x User Manual. Sign up to newsletter. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “X AXIS POWER FEED MILLING BRIDGEPORT ACER ADJUSTABLE SPEED MILLING MACHINE” is in sale since Monday, November 13, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “bilibusyeasy_4″ and is located in Ontario, California. This item can be shipped to United States, Canada, Mexico, Germany.

• Brand: VEVOR
• MPN: GTLPW0010
• Model: APF-500X
• Country/Region of Manufacture: CHINA
• Torque: 150lbs
• Weight: 13.2lbs
• Color: White
• Current: 2.8A
• R.P.M.: 0-210
• Package Dimension: 11 x 7 x 13 inch