Set tools accurately with the Pro Touch Off Gage by Edge Technology. Dramatically decrease set up time and eliminate tool path mismatch. The Pro Touch Off Gage allows you to standardize the way tool offsets are measured in your shop, ensuring every job is setup the same way and runs without issue. To use this gage just lower the tool down onto the contact face until the indicator reads zero. At that point you can be confident that the tool tip is exactly 4 inches from the surface the Pro Touch Off Gage is sitting on. Accurately establishes tool length offsets for CNC milling machines. Large 1 in diameter contact face allows all flutes of the endmill to make contact eliminating issues caused by small variations in flute length. The contact face is lightly spring loaded to protect against overrun. The rectangular base and recessed indicator face allow it to fit between vise jaws on a pair of parallel bars. (competitor models with a round base are unable to do this). Stainless steel contact face. Offset height 4.000 in (101.6mm). Large 2.2 easy to read indicator face. Easy calibration check using 1-2-3 blocks. Gage graduations 0.001. Gage repeatability 0.0002. Body made from red anodized 6061-T6 aluminum. Padded case and manual included. Protected by one or more US patents.

Set tools accurately with the Pro Touch Off Gage by Edge Technology. Dramatically decrease set up time and eliminate tool path mismatch. The Pro Touch Off Gage allows you to standardize the way tool offsets are measured in your shop, ensuring every job is setup the same way and runs without issue. To use this gage just lower the tool down onto the contact face until the indicator reads zero. At that point you can be confident that the tool tip is exactly 4 inches from the surface the Pro Touch Off Gage is sitting on. Accurately establishes tool length offsets for CNC milling machines. Large 1 in diameter contact face allows all flutes of the endmill to make contact eliminating issues caused by small variations in flute length. The contact face is lightly spring loaded to protect against overrun. The rectangular base and recessed indicator face allow it to fit between vise jaws on a pair of parallel bars. (competitor models with a round base are unable to do this). Stainless steel contact face. Offset height 4.000 in (101.6mm). Large 2.2 easy to read indicator face. Easy calibration check using 1-2-3 blocks. Gage graduations 0.001. Gage repeatability 0.0002. Body made from red anodized 6061-T6 aluminum. Padded case and manual included. Protected by one or more US patents.

3D Touch Probe Trigger Edge Finder to Find Desktop Center F/ CNC Milling Machine. 1 x 3D Precision Tool Setting. CR1632 3V button battery. Product Name: Trigger 3D Edge Finder. Item model number: CF-38. Repeat positioning accuracy: =0.005. Probe direction: ±X ±Y +Z. Probe safety stroke: X. Y plane ±20°, Z direction +2.5mm. Trigger life:=3 million times. Power supply: CR1632 3V button battery × 1. Installation of the probe. As shown in the figure below, there is a wrench slot at the probe interface. When installing the probe, you must hold the probe seat to prevent it from rotating, otherwise the internal parts of the probe will be damaged. As shown in the figure below, remove the battery plug, remove the battery with tweezers, replace the battery with a new one, and install the battery according to the “±” mark on the side. After the replacement, plug the battery plug tightly. There is a wrench slot at the probe interface. Remove the battery rubber plug, remove the battery with tweezers, replace the battery with a new one and install the battery according to the “±” mark on the side. After the replacement, plug the battery rubber plug tightly. Adjustment of center deflection. The silver screw is the adjustment screw × 4. Use a dial gauge to measure the runout of the probe ball and adjust the runout to 0. 1x V5 3D touch probe. 1x Stainless steel probe tip. 1x Storage box for storing probe. The DIYO three-coordinate probe can realize quick centering, edge finding, center finding, shape measurement and other functions by connecting the CNC to the knife edge, which greatly;Repeatability Accuracy: 0.01 mm/ 0.0004 in. Solves the trouble of positioning the workpiece during the second clamping during the machining process. Adapt to various control panels such as grbl control panel and Mach3. NPN-NO 3 wires: Red-VCC (DC5-24V power);Yellow: IO/ Signal Output;Black- GND(DCM); Indicator light: green light when power on, red light after triggering. Material of the probe? The shell is made of fine frosted black oxidized aluminum alloy with a flat surface anti-roll design. Material of the stylus? The probe tip/stylus is machined from stainless steel up and down, and the ball head is made of tungsten steel ball, which has the advantage of wear resistance. Please measure and adjust it by yourself after receiving the goods. Be sure to use ER11 spring chucks of AAA or above, otherwise the concentricity of the probe tip will be affected. The feature of waterproof and dustproof greatly extends the service life of the probe. Our product comes with a storage box. The shockproof cotton in this storage box protects the probe well, and also avoids collisions and scratches during transportation. The probe tip is machined from stainless steel up and down, and the ball head is made of tungsten steel ball, which has the advantage of wear resistance. NPN-NO 3 wires: Red-VCC (DC5-24V power);Yellow: IO/ Signal Output;Black- GND(DCM). Repeatability Accuracy: 0.01 mm/ 0.0004 in. Approach Direction: ±X, ±Y, +Z. Over Travel Protection Distance: X- ± 4mm/0.16 in, Y- ±4mm/ 0.16 in,, Z- 2mm/ 0.08 in. Lifetime: > 3 million triggers. Yellow: IO/ Signal Output. Indicator light: green light when power on, red light after triggering. Software Recommendation for 3D Probe (We do not provide software). If you are using a mach3 system, it is recommended to use the open source Probe Wizard. If you are using the grbl system, it is recommended to use Grblgru. Need to turn on the spindle speed? Never, never, never, definitely no. How to distinguish the three wires? The red wire is VCC, the black wire is GND, and the white wire is IO. Why is the concentricity different every time the probe is installed? Because your ER chuck spring clip cannot ensure 100% uprightness. Every time the probe is installed, even if the concentricity is adjusted to 1 wire, there will still be deviations when the probe is removed and installed again. Problem&Feedback Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it. Item must be in it’s original condition and no physical damage.

Set tools accurately with the Pro Touch Off Gage by Edge Technology. Dramatically decrease set up time and eliminate tool path mismatch. The Pro Touch Off Gage allows you to standardize the way tool offsets are measured in your shop, ensuring every job is setup the same way and runs without issue. To use this gage just lower the tool down onto the contact face until the indicator reads zero. At that point you can be confident that the tool tip is exactly 4 inches from the surface the Pro Touch Off Gage is sitting on. Accurately establishes tool length offsets for CNC milling machines. Large 1 in diameter contact face allows all flutes of the endmill to make contact eliminating issues caused by small variations in flute length. The contact face is lightly spring loaded to protect against overrun. The rectangular base and recessed indicator face allow it to fit between vise jaws on a pair of parallel bars. (competitor models with a round base are unable to do this). Stainless steel contact face. Offset height 4.000 in (101.6mm). Large 2.2 easy to read indicator face. Easy calibration check using 1-2-3 blocks. Gage graduations 0.001. Gage repeatability 0.0002. Body made from red anodized 6061-T6 aluminum. Padded case and manual included. Protected by one or more US patents. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “edge_products” and is located in this country: US. This item can be shipped to United States.

• Model: Pro Touch Off Gage
• MPN: 04-000
• Used With: Haas , Mori Seiki , Mazak , Hurco, ProtoTrak Mills
• Used For: Setting Endmill – Tool Offset Length for CNC Mill
• Brand: Edge Technology
• UPC: 738435265885

New Edge model: 04-000 with the 1 dia face. Nice tool, ordered multiply by mistake. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “old-stf-cycle” and is located in this country: US. This item can be shipped to United States.

• Model: Pro Touch Off Gage
• MPN: 04-000
• Used With: Haas , Mori Seiki , Mazak , Hurco, ProtoTrak Mills
• Used For: Setting Endmill – Tool Offset Length for CNC Mill
• Brand: Edge Technology
• UPC: 738435265885

Pro Touch Off Gage (Model: 04-000). Accurately establishes tool length offsets for CNC milling machines. Large 1 in diameter contact face allows all flutes of the endmill to make contact eliminating issues caused by small variations in flute length. The contact face is lightly spring loaded to protect against overrun. The rectangular base and recessed indicator face allow it to fit between vise jaws on a pair of parallel bars. (competitor models with a round base are unable to do this). Stainless steel contact face. Offset height 4.000 in (101.6mm). Large 2.2 in easy to read indicator face. Easy calibration check using 1-2-3 blocks. Gage graduations 0.001. Gage repeatability 0.0002. Body made from red anodized 6061-T6 aluminum. Padded case and manual included. Pro Touch Off Gage. Set tools accurately with the Pro Touch Off Gage by Edge Technology. Dramatically decrease set up time and eliminate tool path mismatch. The Pro Touch Off Gage allows you to standardize the way tool offsets are measured in your shop, ensuring every job is setup the same way and runs without issue. To use this gage just lower the tool down onto the contact face until the indicator reads zero. At that point you can be confident that the tool tip is exactly 4 inches from the surface the Pro Touch Off Gage is sitting on. Protected by one or more US patents. Please request a package invoice before you pay. Related Products by Edge Technology Products. Please take a moment to check out the other high quality machinist gages and tools that we offer. The item “Pro Touch Off Gage z axis CNC tool length offset setter (1 contact face) #04″ is in sale since Friday, February 14, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “edge_products” and is located in Eagle, Idaho. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Costa rica, Dominican republic, Panama, Trinidad and tobago, Guatemala, El salvador, Honduras, Jamaica, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Turks and caicos islands, Bangladesh, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Liechtenstein, Luxembourg, Monaco, Macao, Martinique, Nicaragua, Peru, Pakistan, Paraguay, Viet nam, Uruguay, South africa, Colombia, Antigua and barbuda, Saint lucia, Barbados, Bermuda, Cayman islands, Sri lanka, Maldives, Oman, Reunion, Montserrat, Ukraine.

• Model: Pro Touch Off Gage
• MPN: 04-000
• Brand: Edge Technology
• Used With: Haas , Mori Seiki , Mazak , Hurco, ProtoTrak Mills
• Used For: Setting Endmill – Tool Offset Length for CNC Mill