Sign up to Newsletters. Feed 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage: 110 V, 60 Hz. Rotate speed: 0-200 rpm. Length: 33 cm (13 inch). Width: 20 cm (7.9 inch). Height: 18 cm (7 inch). Gross weight: 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. International Buyers Please Note. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within 12-24hours. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Westminster Hwy, Richmond, BC, Canada. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machine 0-200 RPM” is in sale since Wednesday, December 11, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “hotitemsale” and is located in Richmond. This item can be shipped worldwide.

• Brand: VEVOR
• MPN: 74AZY00331523585124
• Model: AS-250-150
• Power Source: Electric
• Voltage: 110 V, 60 Hz
• Control: See description
• Function: Milling
• Machine Type: Milling Machine
• Type: X-axis
• Torque: 150lbs
• Rotate speed: 0-200 rpm

X-AXIS POWER FEED- Power Feed X-Axis, Voltage: 110V, 50Hz, Rotate Speed: 200 RPM, Max Torque: 150 in-lb, compact and portable design. QUIET & RAPID OPERATION- With speed adjust knob, speed can be adjusted according to operator’s requirement, ranging from 0-9. Jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. DURABLE & LONG LASTING- Safe design helps to protect transmission gear and electronic components; two gears of this power table feed will not mesh and wear at the same spot, maximizing durability and longevity. ERGONOMIC DESIGN- Power feed is equipped with safety feature to protect transmission gear and electronic components as to meet the requirements of ergonomics. EASY SETUP- Small volume and easy installation, noiseless direction changes. Fit almost any vertical knee type milling machine with the 5/8 shaft end. Milling Machine Power Feed. Power Feed Y-Axis, Voltage: 110V, 60Hz, Rotate Speed: 0-200 Rpm. Rotate Speed: 0-200 Rpm. Milling machine power feed features noiseless direction changes and direction control knob for easy and rapid operation. The two gears will not mesh and wear at the same spot, which not only increases durability and longevity but even reduces noise over time. Power table feed won’t vibrate or strain in low speed. Power feed is equipped with safety feature to protect transmission gear and electronic components as to meet the requirements of ergonomics. This small volume and easy installation X-axis power feed is designed to automate the feeding process on Bridgeport type milling machines. Suitable models including vertical turret milling machine, drilling and milling machine and other machinery. 110V Power Feed Milling Machine w/ Rotate Speed 200Rpm. Our brand new Mill Power Feed featuring Max. Rotate speed 200Rpm, power torque 150 in-lb, is for bridgeport and similar knee type milling machines, including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… Quiet & Rapid Operation. Durable & Long Lasting. Max Torque: 150 in-lb. 1 x Power Feed For Milling Machine. 1 x Bevel Gear. 1 x Screw Set. Power Feed Milling Machine. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. California Warehouse: City of Industry, CA. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. Caifornia Warehouse: 18501 Arenth Ave, City of Industry, CA 91748. 300 W Airtex Blvd, Suite 200, Houston, TX 77090. 2125 Gateway Blvd, Hebron, KY 41048. 1000 High Street, Perth Amboy, NJ 08861. The item “Power Feed Y-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM” is in sale since Monday, October 21, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “love-happyshopping” and is located in Rowland Heights, California. This item can be shipped to United States, Canada, Mexico.

• Rotate Speed: 0-200 Rpm
• Max Torque: 150 in-lb
• MPN: ZY8LX00101568946338
• Function: Milling
• Brand: VEVOR
• Machine Type: Milling Machine
• Power Source: Electric
• Control: Manual

AS-250 150Lbs Torque Power Feed Milling Machine X-Axis ALSGS 0-200RPM. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). AS-250-150 X-Axis Power Feed for Milling Machine x 1. Set of Necessary Accessories x 1. Why shop with us? All items are dispatched from our warehouse in HACIENDA HEIGHTS, CA. Some products may be dispatched in more than one carton. International Buyers – Please Note. Please do check everything carefully when receiving the package. Failure to do so might result in damage to your own rights and interests. If you have a problem with the product. We offer detailed product descriptions and images to give you a real advantage in finding the products you’re looking for. With our comprehensive parts support, we help to keep your unit humming. The item “Power Feed X-Axis 150Lbs Torque for Bridgeport Type Milling Machine 0-200 RPM” is in sale since Saturday, March 2, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “pestech” and is located in Hacienda Heights, California. This item can be shipped to United States.

• Brand: pestech
• Model: AS-250
• MPN: ZY8LX00361
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″

For more information on our products. Please send message to us. AS-250 150Lbs Torque Power Feed Milling Machine X-Axis ALSGS 0-200RPM. What Customers Have To About Us. ” Delivered as promised and item is as described “. Just what i was looking for. Had a problem-was able to successfully resolve it. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). 110 V, 60 Hz. 33 cm (13 inch). 20 cm (7.9 inch). 18 cm (7 inch). 6.5 kg(14.3 lb). AS-250-150 X-Axis Power Feed for Milling Machine. Set of Necessary Accessories. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. All items are dispatched from our warehouse in Azusa, CA. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Your product was damaged during transit. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. 25 years Industry Experience. The item “Power Feed X-Axis 150 Lbs Torque for Vertical Milling Machine X axis 0-200 RPM” is in sale since Tuesday, March 26, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “fans-autoparts” and is located in Hacienda Heights, California. This item can be shipped to United States.

• Brand: FANS-AUTO
• Model: AS-250
• MPN: ZY8LX00361
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″

AS-250 150Lbs Torque Power Feed Milling Machine X-Axis ALSGS 0-200RPM. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage: 110 V, 60 Hz. Rotate speed: 0-200 rpm. Length: 33 cm (13 inch). Width: 20 cm (7.9 inch). Height: 18 cm (7 inch). Gross weight: 6.5 kg(14.3 lb). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. AS-250-150 X-Axis Power Feed for Milling Machine. Set of Necessary Accessories. If you have a problem with the product. We will require a picture of the damaged part for verification. All items are dispatched from our warehouse in HACIENDA HEIGHTS, CA. Some products may be dispatched in more than one carton. International Buyers – Please Note. The item “Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM” is in sale since Saturday, March 2, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “zbondfactory-1″ and is located in Hacienda Heights, California. This item can be shipped to United States.

• Brand: ZBOND
• Model: AS-250
• MPN: ZY8LX00361
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″

Specifications: Type: X-axis Material: Aluminium Alloy Color: Black + White Torque: 150 lbs Voltage: 220V Rotate Speed: 0-200 rpm Size: 33x20x18cm / 12.99”x7.87”x7.09” appr. Plug: US Plug / EU Plug (we will base on your country to send the corresponding adapter plug) Features Brand New and high quality. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. X-axis power feed for milling machines. 0-200 rpm rotate speed. Reversible and auto shut-off at end of cut. Excellent speed control in the entire range. Direction control knob for easy and rapid operation. Power table feed won’t vibrate or strain in low speed. Safety feature to protect transmission gear and electronic components. Introductions Speed Adjust Knob Speed can be adjust according to operator’s requirement, ranging from 0-9. Jog Switch Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Attention Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Maintenance Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). International buyers please note: a. The item “220V Power Feed X-Axis 150 Lbs Torque for Bridgeport Milling Machine 0-200 RPM” is in sale since Tuesday, December 4, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “224lala” and is located in HK. This item can be shipped worldwide.

• Country/Region of Manufacture: China
• MPN: IAC280941
• Brand: Unbranded/Generic
• Manufacturer Part Number: IAC280941

Better price, Top Quality, expert Service support. Live demo of multiple products. Owned and operated company. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. AS-250-150 X-Axis Power Feed for Milling Machine X 1. Set of Necessary Accessories X 1. Product Manual X 1. All items are dispatched from our warehouse in Azusa, CA. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. We never want our customers to wait for parts, we have plenty of parts available for every product. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. The item “AS-250 X AXIS POWER FEED KNEE MILLS FOR BRIDGEPORT MILLING MACHINE 0-200 RPM” is in sale since Saturday, March 2, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “ac-racing” and is located in Hacienda Heights, California. This item can be shipped to United States.

• Brand: AC-RACING
• Model: AS-250
• MPN: ZY8LX00361
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″

Sign up to Newsletters. X-Axis Power Feed 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage: 110 V, 60 Hz. Rotate speed: 0-200 rpm. Length: 33 cm (13 inch). Width: 20 cm (7.9 inch). Height: 18 cm (7 inch). Gross weight: 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM” is in sale since Wednesday, October 18, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “frontiertosale” and is located in Ontario, California. This item can be shipped to United States, Canada, Germany.

• Brand: VEVOR
• MPN: NJGTL004
• Bundle Listing: Yes
• Model: AS-250-150
• Country/Region of Manufacture: CHINA
• RPM: 0~200
• TORQUE: 150LBS
• Type: X-axis
• VOLTAGE: 110 V, 60 Hz
• Gross weight: 6.5 kg(14.3 lb

Power Feed X-Axis 150 Lbs Torque Type Milling Machines 0-200 RPM. Specification: Color: white Material: metal Voltage:AC 110 V, 50/ 60 Hz Power:9W Torque: 150 lbs Rotate speed: 0-200 rpm Plug: US Item size:22932.5cm Package size: 31.528.520CM. Package Included: 1 x Milling Machine 1 x Set of Necessary Accessories 1 x Manual. AC 110 V, 50/ 60 Hz. Please go to “DHL eCommerce” to check your order. OR, you may choose to have a replacement. We will reply you ASAP. Our aim is to provide Top Level Customer Service, normally so we will try our best to solve any problem. The item “Power Feed X-Axis 150 Lbs Torque Type Milling Machines 0-200 RPM” is in sale since Monday, September 10, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “ohbuybuybuy” and is located in Chino, California. This item can be shipped to United States.

• Brand: Unbranded/Generic
• MPN: Does Not Apply
• Material: metal
• Voltage: AC 110 V,50/ 60 Hz
• UPC: Does not apply
• Power: 9W
• Torque: 150 lbs
• Rotate speed: 0-200 rpm

You may also like. Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage: 110 V, 60 Hz. Rotate speed: 0-200 rpm. Length: 33 cm (13 inch). Width: 20 cm (7.9 inch). Height: 18 cm (7 inch). Gross weight: 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. Protective packing material will be added in your package if we believe item can be damaged easily in transit. Tracking numbers will be available in 24 hours except weekends and holidays. Best Prices: By avoiding too many other companies marketing and packaging costs, we deliver the same quality products at a fraction of the cost. Our products are also tested for quality assurance purposes. We trust that you will have a happy experience when shopping with us! We appreciate your business! E-mails are answered Monday through Saturday. Please allow up to 48 hours for a response to your message. The item “Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM” is in sale since Tuesday, August 21, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “niuqiang29″ and is located in cn. This item can be shipped worldwide.

• Brand: VEVOR
• MPN: ZCXZG0085
• Model: AS-250-150
• Country/Region of Manufacture: CHINA
• RPM: 0~200
• TORQUE: 150LBS
• Type: X-axis
• VOLTAGE: 110 V, 60 Hz
• Gross weight: 6.5 kg(14.3 lb)