Digital readouts & Machinery. Voltage: 110V, or 220V 50/60Hz. Rotate speed: 0-200 RPM. Max torque: 450 in-lb. Max feed rate: 650mm/min. Max return speed: 850mm/min. Dimension: 8 x 4.5 x 13 inches. Package size: 11.8 x 8.7 x 13.8 inches. Gross weight: 16.5 lbs. Brand new power feed. X traverse (left-right travel). These are powered by a Standard 220v or 110V Plug So No Wiring is Required! This set includes everything you should need to install this power feed, including the power feed unit, table mounting bracket, drive gear, shims, safety stop, and hardware. 1 x Power Feed For Milling Machine. 8 x Adjustable Pad. 2 x Tiavel Stop Assembly. 1 x Bevel Gear. 1 x Dial Nut. 1 x Locking Nut. 1 x Product Manual. Brand new Power feed ALB-310X. Variable speeds – Torque 450 in-lb. Available in 220V or 110V (X). Small volume and easy installation. Excellent speed control in the entire range. Variable speeds â Torque 450 in-lb. Add to Favourites. The item “Power feed for Horizontal milling machine ALB-310sx 110V / 220V free shipping” is in sale since Monday, August 20, 2018. This item is in the category “Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “digitechdirect” and is located in Endeavour Hills . This item can be shipped worldwide.

• Modified Item: No
• Custom Bundle: No
• Non-Domestic Product: No

Digital readouts & Machinery. Voltage: 110V, or 220V 50/60Hz. Rotate speed: 0-200 RPM. Max torque: 450 in-lb. Max feed rate: 650mm/min. Normally speed & rapid switch. Max return speed: 850mm/min. Dimension: 8 x 4.5 x 13 inches. Package size: 11.8 x 8.7 x 13.8 inches. Gross weight: 16.5 lbs. Brand new power feed. X traverse (left-right travel). Brand New AL-310S X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, Firstetc. The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot; this not only increases durability and longevity but even reduces noise over time. 1 x Power Feed For Milling Machine. 8 x Adjustable Pad. 2 x Tiavel Stop Assembly. 1 x Bevel Gear. 1 x Dial Nut. 1 x Locking Nut. 1 x Product Manual. Brand new Power feed AL-310SX. Variable speeds Torque 450 in-lb. Available in 220V or 110V (X Y Z). Small volume and easy installation. Excellent speed control in the entire range. Add to Favourites. The item “Power feed milling machine AL-310S 200RPM 450in-lb110V / 220V free shipping” is in sale since Sunday, September 11, 2016. This item is in the category “Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “digitechdirect” and is located in Endeavour Hills . This item can be shipped worldwide.

• Modified Item: No
• Custom Bundle: No
• Non-Domestic Product: No

220V Mini precision high-speed bench drill Drilling milling machine + Workbench. 340w bench drill for drilling PCB PVC thin wood products. Features are quick drilling, clamping the drill bit is small. Power: 340W Speed: 16000r / min Stroke: 22mm Hold: 1-10mm Weight: 5.5kg. 1x bench drill Drilling milling machine 1x Workbench 1x English manual. The item “220V Mini High-speed Bench Drill Drilling PCB PVC Milling Machine + Workbench” is in sale since Tuesday, April 18, 2017. This item is in the category “Business, Office & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “cnc-mall” and is located in Shenzhen. This item can be shipped worldwide.

• Brand: Unbranded/Generic
• MPN: Does Not Apply
• Type: Drilling milling machine
• Power: 340W
• Voltage: 220-240V

Item include: 1AL-310 power feed for X axis milling machine. It includes accessories for installion. The shaft is 16mm for mounting. Milling machine power feeding apparatus with low noise, large torque, high speed, convenient installation and flexible operation, good appearance, as to meet the requirements of ergonomics. It’ll just take you 1 minute. We will work with you to solve any problems. The item “Best price ALSGS AL-310 110V 220V Power feed for Vertical milling machine X axis” is in sale since Thursday, August 9, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “88490755″ and is located in China. This item can be shipped worldwide.

• Application: For milling x axis
• Model: AL-310 for x axis milling
• Modified Item: No
• Country/Region of Manufacture: China
• Custom Bundle: No
• MPN: No have
• Brand: ALSGS
• Non-Domestic Product: No
• Voltage: 110V / 220V

ALSGS AL-310S 110V / 220V milling machine power feed 450 in-lb power feed machinery for X , Y & Z axis. Name: milling machine, electronic feeding device. Model: AL – 310S (X, Y, Z). The main motor power: 95W. Maximum speed: 200 RPM. The maximum torque: in 450 – lb. Power requirement: AC 110V / 220V +/-20%, 50/60 hz (optional). Suitable model: vertical turret milling machine, drilling and milling machine and other machinery. After ordering please tell us. The axis(X, Y or Z axis) that you need, or we will default send X axis. There are 110V & 220V 2 types for choice, please tell us which voltage input type do you need, or we will default send 110V. The item “ALSGS AL-310S 110V / 220V milling machine power feed 450 in-lb for X axis” is in sale since Tuesday, September 4, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “machinertool0″ and is located in . This item can be shipped worldwide.

• Brand Name: Fivetecnc
• Brand: ALSGS
• MPN: Does Not Apply
• Model Number: ALSGS AL-310

Specifications: Type: X-axis Material: Aluminium Alloy Color: Black + White Torque: 150 lbs Voltage: 220V Rotate Speed: 0-200 rpm Size: 33x20x18cm / 12.99”x7.87”x7.09” appr. Plug: US Plug / EU Plug (we will base on your country to send the corresponding adapter plug) Features Brand New and high quality. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. X-axis power feed for milling machines. 0-200 rpm rotate speed. Reversible and auto shut-off at end of cut. Excellent speed control in the entire range. Direction control knob for easy and rapid operation. Power table feed won’t vibrate or strain in low speed. Safety feature to protect transmission gear and electronic components. Introductions Speed Adjust Knob Speed can be adjust according to operator’s requirement, ranging from 0-9. Jog Switch Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Attention Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Maintenance Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). International buyers please note: a. The item “220V Power Feed X-Axis 150 Lbs Torque for Bridgeport Milling Machine 0-200 RPM” is in sale since Tuesday, December 4, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “224lala” and is located in HK. This item can be shipped worldwide.

• Country/Region of Manufacture: China
• MPN: IAC280941
• Brand: Unbranded/Generic
• Manufacturer Part Number: IAC280941

Table travel (X, Y): 490x155mm. The item “Variable Speed Brushless DC Motor Milling and Drilling machine WMD25V 220V New” is in sale since Tuesday, June 6, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “e-lab-4u” and is located in cn,cn. This item can be shipped worldwide.

• Brand: Unbranded//Generic
• MPN: Does Not Apply

The spindle was removed and sent to wells Index and had the bearings inspected and was re ground to R8. The head was taken apart and removed the grease some put in it. (it should have oil not grease). All the parts and gears look amazing, I have pictures. The oil seal was replaced for the power down feed. And it can be done without taking the machine apart. Comes with a few R8 tooling/end mills and a Jacobs ball bearing chuck. The 6 vise was also taken apart and cleaned and painted. The item “INDEX Model 55 milling machine 1955 R8 knee mill Wells Bridgeport 220V” is in sale since Monday, December 3, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “perf0rmanceplus” and is located in Klamath Falls, Oregon. This item can’t be shipped, the buyer must pick up the item.

• Brand: Index
• Country/Region of Manufacture: United States
• Bundle Listing: No
• MPN: Model 55

Bridgeport M Head from a milling machine. This sale is for the head only, The’swivel’ or’knuckle’ is not included. Like in the last photo with all the’black’ on it. Quill is 7 B&S Brown and Sharpe. US Motor, 220 volt, ½ HP, 3-phase. SN 519610, 1200 rpm I ran this motor off a rotary phase converter and not a static phase converter. A little damage to the casting where the oilier screws in. This does not in any way impact the operation, but I want to provide full disclosure to all known flaws. Comes with the following items. Collet set (All of them are 7 B&S taper). 3/8 Cant read anything on it but looks like Bridgeport brand. I have no idea why a 21/64. 7/16 Unknown modern brand (probably Chinese). A ½ shank is tight, and a 31/64″ drill is a little loose – I think it is 1/2″ Bridgeport brand… But I cannot be certain. Jacobs brand drill chuck arbor 7 B&S to 3JT (Jacobs Taper). Jacobs brand drill chuck arbor 7 B&S to 6 JT (Jacobs Taper). Three (3) National Twist Drill and Tool Company Left Hand cut (LH) 6 flute 7/8 HSS endmills (non center cutting) Length of flute is about 1.470. One (1) National Twist Drill and Tool Company Left Hand cut (LH) 6 flute 7/8 HSS endmills (non center cutting) Length of flute is about 1.130. This one has had the end portion of the flutes cut or ground of f. Local pick-up is free. My height weight and dimensions are an estimate. I will crate, I will bring it to the depot and get it going on my end. I will crate and bring to the depot for free. Here’s a video of the head running. The item “Bridgeport Milling Machine M Head with Collets, Arbors, End Mills 1/2hp 3ph 220v” is in sale since Tuesday, January 1, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “yaker” and is located in Rocky Mount, Virginia. This item can be shipped to United States.

• Brand: Bridgeport
• Model: M Head
• Country/Region of Manufacture: United States

Recent searches

• bridgeport m head

This Brown & Sharpe No. 2 Plain Milling Machine. Is in excellent mechanical condition and was removed from a working environment. As seen in photos, this machine shows normal signs of use. This item came from a local shop that upgraded equipment and was in use prior to removal. Although we cannot perform full testing (lack of three phase power) we are confident this machine is fully functional. We urge customers to view all photos as they show overall condition, included accessories, and functionality. We will be happy to supply additional information as well as photos so p. Track Page Views With. Auctiva’s FREE Counter. The item “Brown & Sharpe No. 2 Plain Milling Machine 3HP 220V 60HZ 3PH Serial No 502-20-6″ is in sale since Wednesday, November 15, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “labtechsalescom” and is located in New Ipswich, New Hampshire. This item can be shipped to United States.

• Brand: Brown & Sharpe
• Model: No. 2
• MPN: 502-20-6