Please call with any questions. We will assist you in any reasonable way to help get your items to your destination, All checks subject to bank verification. Please Call two zero three, five nine two, eight four zero two with any questions or concerns, Thank You! You are welcome to inspect any machine by appointment. Guerrera Machine Company, LLC. Will not be held liable for any inaccurate information. The item “Bridgeport Milling Machine with Servo 150 Power Feed” is in sale since Monday, December 17, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “guerreramachinecompanyllc” and is located in Watertown, Connecticut. This item can be shipped to United States.

• Brand: Bridgeport
• MPN: Does Not Apply

The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Your product was damaged during transit. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that¡¯s why our customers keep coming back. The item “Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM” is in sale since Tuesday, December 15, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “vipshopmarket” and is located in Westbury, New York. This item can be shipped to United States.

• Brand: VIPSHOPMARKET
• Model: AS-250-150
• MPN: ZY8LX00361
• Voltage: 110V
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″
• Gross weight: 6.5 kg(14.3 lb)
• Warranty: 5 Years
• Function: Milling
• Machine Type: Milling Machine
• Power Source: Electric
• Control: Manual

Sign up to Newsletters. Feed 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage: 110 V, 60 Hz. Rotate speed: 0-200 rpm. Length: 33 cm (13 inch). Width: 20 cm (7.9 inch). Height: 18 cm (7 inch). Gross weight: 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. International Buyers Please Note. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within 12-24hours. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Westminster Hwy, Richmond, BC, Canada. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machine 0-200 RPM” is in sale since Wednesday, December 11, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “hotitemsale” and is located in Richmond. This item can be shipped worldwide.

• Brand: VEVOR
• MPN: 74AZY00331523585124
• Model: AS-250-150
• Power Source: Electric
• Voltage: 110 V, 60 Hz
• Control: See description
• Function: Milling
• Machine Type: Milling Machine
• Type: X-axis
• Torque: 150lbs
• Rotate speed: 0-200 rpm

Fadal VMC 15XT, 2004 – Never Ran Production, Under Power. We are pleased to offer the following for your consideration. Table Size: 38″ x 16″. Table Load Capacity: 750lbs. Full Load Current: 38A. Taper – CAT #40. Speed – 10 – 7,500 RPM. Motor – 15 HP. Machine Dimensions: 90″ x 77″ x 101. Brand new Dies on it. Control – Fadal CNC. 8 Meg Expandable Memory. All specifications are assumed to be correct but must be confirmed by purchasing entity. Revelation Machinery encourages first-hand inspection of all used machinery. Please verify all of the specs listed for this machine. Listing and template services provided by inkFrog. The item “Fadal VMC 15XT, 2004 Never Ran Production, Under Power” is in sale since Friday, September 25, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “revelationmachinery” and is located in Bardstown, Kentucky. This item can be shipped to United States.

• Brand: Fadal

The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. We have Four warehouses located in CA, NY, NJ & GA. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. The item “X-Axis 150 LBS Torque Power Feed For Bridgeport Vertical Milling Machine 200 RPM” is in sale since Wednesday, September 23, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “homesupplies01″ and is located in Westbury, New York. This item can be shipped to United States.

• Voltage: 110V
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″
• Gross weight: 6.5 kg(14.3 lb)
• Warranty: 5 Years
• Function: Milling
• Machine Type: Milling Machine
• Power Source: Electric
• Control: Manual
• Brand: VEVOR
• Model: AS-250-150
• MPN: ZCXZG0085

1997 Haas VF-2 VMC Quote #989. Travel 30 x 16 x 20. 20 Station Carousel Tool Changer 7,500 RPM Spindle. 40 Taper 20 HP Programmable Coolant Chip Auger System Coolant System. All rigging, inspections, preparations and trucking buyers responsibility. Locations of machine vary, contact George Malouin, Rockfish Machinery. The item “Haas VF-2 VMC, 7500 RPM, Auger, Cool and under power for inspection” is in sale since Tuesday, September 15, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “rockfish-machinery” and is located in Los Gatos, California. This item can be shipped to United States.

• Model Year: 1997
• Brand: Haas

Appears to be 1996. In excellent working condition and ready for inspection in Allen TX. Under air and power! Comes with fourth axis integrated for full 4 axes machining. Also comes with a USB adaptor for easy G-Code programming. The fourth axis is an HA5C, which receives 5C collets for work holding by the rotary axis. Machine holds excellent tolerances. The item “Haas VF1 CNC with 4TH AXIS INSTALLED- Under Power DFW Area” is in sale since Tuesday, September 1, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “direct-drive-robotics” and is located in Allen, Texas. This item can be shipped to United States.

• Brand: Haas
• Control: CNC

The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. We have Four warehouses located in CA, NY, NJ & GA. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. The item “X-Axis Power Feed for Vertical Milling Machine 150 Lbs Torque Knee Mills Fits” is in sale since Thursday, July 16, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “homesupplies01″ and is located in Westbury, New York. This item can be shipped to United States.

• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″
• Gross weight: 6.5 kg(14.3 lb)
• Warranty: 5 Years
• Machine Type: Milling Machine
• Power Source: Electric
• Function: Milling
• Control: Manual
• Voltage: 110V
• Brand: VEVOR
• Model: AS-250-150
• MPN: ZCXZG0085

Z-AXIS POWER FEED- The power feed for milling machine is of Z-Axis, Voltage: 110V, 60Hz, Rotate Speed: 200 RPM, Max Torque: 150 in-lb. Compact and portable design. QUIET & RAPID OPERATION- With speed adjust knob, speed can be adjusted according to operator’s requirement, ranging from 0-9. Jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. DURABLE & LONG LASTING- Safe design helps to protect transmission gear and electronic components; two gears of this mill power feed will not mesh and wear at the same spot, maximizing durability and longevity. ERGONOMIC DESIGN- Feed milling machine is equipped with safety feature to protect transmission gear and electronic components as to meet the requirements of ergonomics. EASY SETUP- Small volume and easy installation, noiseless direction changes. Fit almost any vertical knee type milling machine with the 5/8 shaft end. Power Feed Z-Axis, Voltage: 110V, 60Hz, Rotate Speed: 0-200 Rpm. Rotate Speed: 0-200 Rpm. Features noiseless direction changes and direction control knob for easy and rapid operation. The two gears will not mesh and wear at the same spot, which not only increases durability and longevity but even reduces noise over time. Power table feed won’t vibrate or strain in low speed. Power feed is equipped with safety feature to protect transmission gear and electronic components as to meet the requirements of ergonomics. This small volume and easy installation Z-axis power feed is designed to automate the feeding process on milling machines. Suitable models including vertical turret milling machine, drilling and milling machine and other machinery. 150 in-lb Z-Axis Power Feed Rotate Speed 200Rpm. Our brand new power feed milling machine featuring Max. Rotate speed 200Rpm, power torque 150 in-lb, is for bridgeport and similar knee type milling machines, including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… Quiet & Rapid Operation. Durable & Long Lasting. Max Torque: 150 in-lb. 1 x Power Feed For Milling Machine. 1 x Bevel Gear. 1 x Screw Set. Power Feed Milling Machine. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. California Warehouse: City of Industry, CA. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. Caifornia Warehouse: 18501 Arenth Ave, City of Industry, CA 91748. 300 W Airtex Blvd, Suite 200, Houston, TX 77090. 2125 Gateway Blvd, Hebron, KY 41048. 1000 High Street, Perth Amboy, NJ 08861. The item “Power Feed Mill Power Feed 150 in-lb Z-Axis for Drilling & Milling Machine” is in sale since Friday, November 1, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “love-happyshopping” and is located in Rowland Heights, California. This item can be shipped to United States, Canada, Mexico.

• Rotate Speed: 0-200 Rpm
• Max Torque: 150 in-lb
• MPN: PWFRC00311572593305
• Function: Milling
• Brand: Vevor 1572593305825232
• Machine Type: Milling Machine
• Power Source: Electric
• Control: Manual
• Voltage: 110V, 60Hz

Bridgeport Milling Machine 9 X 36 Table. Will load your truck for free. Thanks for looking from marcummachine. The item “Bridgeport Milling Machine 9 X 36 Table, TOOLING, POWER FEED, J HEAD” is in sale since Tuesday, October 20, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “greg9991″ and is located in New London, Ohio. This item can’t be shipped, the buyer must pick up the item.

• Brand: Bridgeport
• Machine Type: Milling Machine