Bridgeport model 6F power feed gearbox and switch housing, used. There is no motor or control board, please see pictures for exactly what is included.

About of the item. Y-Axis power feed is made of aluminuml;Power Parameter: 95Watt, 110V input voltage, 50/60Hz, single phase;Rotate Speed:0-200 RPM. Max Torque:450in-lb;Max feed rate: 650mm/min; Max return speed: 850mm/min. AUTOMATIC AND MANUAL CONTROL? You can set this power feed to work at automatic constant speed to free your hands or work by manually adjusting the speed control knob to do more precise milling work. And this mulitfunctional milling machine power feed can work with excellent speed control in the entire range according to your needs. This power feed adopts Gleason Spiral Bevel Gear with advantages of stable transmission ratio, low transmission noise, high transmission efficiency and high bearing capacity. And when fast transmission, if the tool collides with the work piece or reverses instantaneously, the special safety device protects the transmission plastic gear and electronic parts from damage. PORTABLE AND EASY TO INSTALL? This power feed for milling machine is compact and portable. Weight: 5kg/11lbs, Size: 74.511.5 inch. And whether it is for a novice or a skilled operator, it is very easy to install this power feed according to the instruction and online video or by yourself. This power feed fits some milling machines like Bridgeport, Precision Matthews, Enco, Jet, Sharp, Acer, Webb, etc. This milling table power feed fits some vertical knee type mills with the same mounting pattern and a 5/8 diameter shaft on the end, But it will NOT fit mills with a different mounting pattern or different sized leadscrews like powermatic and some other odd sized machines, so please make sure yours is the typical Bridgeport type as mentioned above.

Used-Tested good before removal. AC Input 120 VAC. DC Output: +5VDC, +12VDC, -12VDC.

About of the item. Y-Axis power feed is made of aluminuml;Power Parameter: 95Watt, 110V input voltage, 50/60Hz, single phase;Rotate Speed:0-200 RPM. Max Torque:450in-lb;Max feed rate: 650mm/min; Max return speed: 850mm/min. AUTOMATIC AND MANUAL CONTROL? You can set this power feed to work at automatic constant speed to free your hands or work by manually adjusting the speed control knob to do more precise milling work. And this mulitfunctional milling machine power feed can work with excellent speed control in the entire range according to your needs. This power feed adopts Gleason Spiral Bevel Gear with advantages of stable transmission ratio, low transmission noise, high transmission efficiency and high bearing capacity. And when fast transmission, if the tool collides with the work piece or reverses instantaneously, the special safety device protects the transmission plastic gear and electronic parts from damage. PORTABLE AND EASY TO INSTALL? This power feed for milling machine is compact and portable. Weight: 5kg/11lbs, Size: 74.511.5 inch. And whether it is for a novice or a skilled operator, it is very easy to install this power feed according to the instruction and online video or by yourself. This power feed fits some milling machines like Bridgeport, Precision Matthews, Enco, Jet, Sharp, Acer, Webb, etc. This milling table power feed fits some vertical knee type mills with the same mounting pattern and a 5/8 diameter shaft on the end, But it will NOT fit mills with a different mounting pattern or different sized leadscrews like powermatic and some other odd sized machines, so please make sure yours is the typical Bridgeport type as mentioned above.

This air operated power draw bar comes complete with a 3/4 socket. It uses your stock milling machine drawbar, and if your drawbar is not a 3/4 inch DB, you can use any size socket you desire, the butterfly impact is a 3/8 in model. This power drawbar will fit Bridgeport and most other import. Also included is a pressure regulator unit, you simply bolt the power draw bar to the top of your mill using two 1/4-20 bolts, and connect the air supply, the regulator is preset to 90 psi, and believe me its more than enough pressure to do the job. Please note: This will not fit the Bridgeport J head machines… J-head power drawbars include 3 spacers for mounting. Please Note Concerning Mounting. There are 12 mounting holes, drilled on a 4.35 inch bolt hole circle. If you have a Bridgeport clone or other milling machine, measure your mounting holes to determine if this product will fit your mill. If your holes do not line up, this product can still work if you are willing to locate, drill and tap 2 mounting holes. Measure and be sure, thanks!

VEVOR Milling Machine Power Feed. Our power table feed brings a stable transmission ratio and high load-bearing capabilities. Take control of speed with ease using the manual lever and automatic knob. Ideal for 5/8” end shaft diameter machines and X-axis milling machines. Experience efficiency and reliability like never before! Equipped with Gleason spiral bevel gears, our milling machine power feed ensures a stable transmission ratio, low noise output, high transmission efficiency, and excellent load-bearing capacity. With noise levels? 85dB, providing a conducive environment for your work or study without disruptions. Our power feed table mill is equipped with overload protection. In instances of rapid transmission, if there is a collision or instantaneous reversal between the tool and the workpiece, a special security mechanism safeguards the gearbox’s plastic gears and electronic components from damage. Our compact and lightweight power table feed is easy to install and operate. The control panel features clear functions, making the operation straightforward. Additionally, we provide a detailed installation and user manual, ensuring you have all the information you need to operate effectively. Our power feed milling machine comes with a set of sturdy metal parts that are built to last, including 1 x copper gear, 1 x install the retainer plate, 3 x fixing screws, 2 x limit switch springs, 15 x adjusting shims, 1 x bearing inner ring, and 1 x copper gear gasket. Ultimate High-Compatibility Solution: Our power feed table mill Includes everything needed to mount on most knee-type mills with a 5/8” end shaft diameter that shares the same installation pattern, such as Bridgeport, Precision Matthews, Enco, Jet, Sharp, Acer, Webb, and others. Infinitely Variable Speed Control: With the continuously variable speed knob, you can adjust the speed according to your needs. Our milling machine power feed offers a rated torque of 150 in-lb(16.9 NM), a maximum speed of 200 RPM, a maximum feed rate of 965 mm/min, and a maximum return speed of 1385 mm/min. Highly Stable and Efficient: Featuring Gleason spiral bevel gears, our power table feed boasts stable transmission ratios, low noise, high transmission efficiency, and high load-bearing capacity. Plus, it comes with a special security device that protects the gearbox plastic gears, and electronic components from damage in the event of tool collision or sudden reversal during rapid transmission. Easy to Use, Manual or Automatic: Our power feed milling machine offers two different speed adjustment modes: manual and automatic. With manual control buttons, you can adjust the speed as needed. Alternatively, set the device to automatic constant speed mode for hands-free operation, making your milling tasks a breeze. Designed for X-axis Direction: This power feed woodworking enables smooth movement in the X-axis direction. People Who Bought This Item Also Bought. AL-310S X-AXIS Power Feed Milling Machine 450in-lb peak 0-200RAL-310S Bridgeport. VEVOR Square Air Cooled Spindle Motor 2.2KW CNC Spindle Motor 220V ER20 Collet. VEVOR BS-0 Semi 5 Indexing Dividing Head 3-Jaw Chuck Tailstock For CNC Milling. VEVOR Compound Milling Machine Work Table 2 Axis Cross Slide Bench Drill Vise. VEVOR 8 Precision Horizontal and Vertical Rotary Table. VEVOR 2.2KW Air Cooled Spindle Motor for CNC Router Milling Engraving 4 Bearings. VEVOR Milling Drilling Machine Worktable Cross Slide Table 4″ X 7.3″ Bench Table. VEVOR Variable Frequency Drive Inverter 1.5KW Air cooling Spindle Motor. VEVOR Indexing Dividing Head 6 3 Jaw Chuck & Tailstock for CNC Milling Machine. VEVOR Tilting Milling Table Tilting Angle Milling Machine Adjustable Plate. Tilting Table 5 x 7inch for Milling Machines Swivel Angle Plate Adjustable Plate. VEVOR 2.2KW Water-Cooled Spindle Motor ER20 Cooling Engraving Milling Grinding. VEVOR 2.2KW CNC Water Cooled Spindle Motor ER20 VFD Clamp Pump Pipe Collet 110V. ER20 4kw air-cooled spindle motor engraving milling grind cnc four bearing. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. Please be aware that. Please DO NOT fill in the PO Box address. California Warehouse: City of Industry, CA. New York State Warehouse: Perth Amboy, NJ. Georgia Warehouse: Austell, GA. North Carolina Warehouse: Grove NC. Oregon Warehouse: AIRPORT WAY Portland, OR. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. VEVOR is a leading brand that specializes in equipment and tools. Along with thousands of motivated employees, VEVOR is dedicated to providing our customers with tough equipment & tools at incredibly low prices. Power Feed Milling Machine. 450 lbs / 204 kg. 150 lbs / 68 kg. 135 lbs / 155 kg. 0 – 200 RPM. 0 – 210 RPM. 16.5 lbs / 7.5 kg. 14.3 lbs / 6.5 kg. 13.2 lbs / 6 kg.

A&T Universal Air Power Drawbar. Machinist changes tools manually 10-15 times per day at 3 minutes per tool change. By installing the Air Power Drawbar unit, machinists change tools within seconds and eliminate the need to climb for the drawbar and the use of ¾ wrench. With the use of A&T Air Power Drawbar unit, one can save approximately 12 hours per month. The unit can be installed within 25 minutes without any special drawbar needed. 19 mm socket for R-8 or 30 taper and 21 mm socket for 40 taper spindles. The unit is powered by shop air 90 P. I without electrical wiring and also no drilling or tapping is required for variable speed mill head. A uniquely designed air motor with some parts made from nickel, chrome tungsten alloy steel. Operators can change tools with control valve pushed button to engage or disengage the tools. Model #: ADB-300 V.

VEVOR Milling Machine Power Feed. Our power table feed brings a stable transmission ratio and high load-bearing capabilities. Take control of speed with ease using the manual lever and automatic knob. Ideal for 5/8” end shaft diameter machines and Z-axis milling machines. Experience efficiency and reliability like never before! Equipped with Gleason spiral bevel gears, our milling machine power feed ensures a stable transmission ratio, low noise output, high transmission efficiency, and excellent load-bearing capacity. With noise levels? 85dB, providing a conducive environment for your work or study without disruptions. Our power feed table mill is equipped with overload protection. In instances of rapid transmission, if there is a collision or instantaneous reversal between the tool and the workpiece, a special security mechanism safeguards the gearbox’s plastic gears and electronic components from damage. Our compact and lightweight power table feed is easy to install and operate. The control panel features clear functions, making the operation straightforward. Additionally, we provide a detailed installation and user manual, ensuring you have all the information you need to operate effectively. Our power feed milling machine comes with 1 x copper gear, 1 x install the retainer plate, 2 x limit blocks, 4 x fixing screws, 1 x limit switch waterproof box, 2 x limit switch springs, 15 x adjusting shims, 1 x extended shaft, 11 x extended shaft springs, 1 x copper gear gasket, and 1 x flat key. Ultimate High-Compatibility Solution: Our power feed table mill Includes everything needed to mount on most knee-type mills with a 5/8” end shaft diameter that shares the same installation pattern, such as Bridgeport, Precision Matthews, Enco, Jet, Sharp, Acer, Webb, and others. Infinitely Variable Speed Control: With the continuously variable speed knob, you can adjust the speed according to your needs. Our milling machine power feed offers a rated torque of 450 in-lb(50.7 NM), a maximum speed of 200 RPM, a maximum feed rate of 965 mm/min, and a maximum return speed of 1385 mm/min. Highly Stable and Efficient: Featuring Gleason spiral bevel gears, our power table feed boasts stable transmission ratios, low noise, high transmission efficiency, and high load-bearing capacity. Plus, it comes with a special security device that protects the gearbox plastic gears, and electronic components from damage in the event of tool collision or sudden reversal during rapid transmission. Easy to Use, Manual or Automatic: Our power feed milling machine offers two different speed adjustment modes: manual and automatic. With manual control buttons, you can adjust the speed as needed. Alternatively, set the device to automatic constant speed mode for hands-free operation, making your milling tasks a breeze. Designed for Z-axis Direction: This power feed woodworking enables smooth movement in the Z-axis direction. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. Please be aware that. Please DO NOT fill in the PO Box address. California Warehouse: City of Industry, CA. New York State Warehouse: Perth Amboy, NJ. Georgia Warehouse: Austell, GA. North Carolina Warehouse: Grove NC. Oregon Warehouse: AIRPORT WAY Portland, OR. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. VEVOR is a leading brand that specializes in equipment and tools. Along with thousands of motivated employees, VEVOR is dedicated to providing our customers with tough equipment & tools at incredibly low prices.

VEVOR Milling Machine Power Feed. Our power table feed brings a stable transmission ratio and high load-bearing capabilities. Take control of speed with ease using the manual lever and automatic knob. Ideal for 5/8” end shaft diameter machines and X-axis/Z-axis milling machines. Equipped with Gleason spiral bevel gears, our milling machine power feed ensures a stable transmission ratio, low noise output, high transmission efficiency, and excellent load-bearing capacity. With noise levels? 85dB, providing a conducive environment for your work or study without disruptions. Our power feed table mill is equipped with overload protection. In instances of rapid transmission, if there is a collision or instantaneous reversal between the tool and the workpiece, a special security mechanism safeguards the gearbox’s plastic gears and electronic components from damage. Our compact and lightweight power table feed is easy to install and operate. The control panel features clear functions, making the operation straightforward. Additionally, we provide a detailed installation and user manual, ensuring you have all the information you need to operate effectively. Our power feed milling machine comes with a set of sturdy metal parts that are built to last, including 1 x copper gear, 1 x install the retainer plate, 3 x fixing screws, 2 x limit switch springs, 15 x adjusting shims, 1 x bearing inner ring, and 1 x copper gear gasket. Here we will provide you with 3 types of Power Feed for your option: X-Axis 450 in-lb, X-Axis 150 in-lb, Z-Axis 450 in-lb. Ultimate High-Compatibility Solution: Our power feed table mill Includes everything needed to mount on most knee-type mills with a 5/8” end shaft diameter that shares the same installation pattern, such as Bridgeport, Precision Matthews, Enco, Jet, Sharp, Acer, Webb, and others. Infinitely Variable Speed Control: With the continuously variable speed knob, you can adjust the speed according to your needs. Our milling machine power feed offers a rated torque of 450 in-lb(50.7 NM)/150 in-lb(16.9 NM), a maximum speed of 200 RPM, a maximum feed rate of 965 mm/min, and a maximum return speed of 1385 mm/min. Highly Stable and Efficient: Featuring Gleason spiral bevel gears, our power table feed boasts stable transmission ratios, low noise, high transmission efficiency, and high load-bearing capacity. Plus, it comes with a special security device that protects the gearbox plastic gears, and electronic components from damage in the event of tool collision or sudden reversal during rapid transmission. Easy to Use, Manual or Automatic: Our power feed milling machine offers two different speed adjustment modes: manual and automatic. With manual control buttons, you can adjust the speed as needed. Alternatively, set the device to automatic constant speed mode for hands-free operation, making your milling tasks a breeze. Designed for X-axis Direction: This power feed woodworking enables smooth movement in the X-axis/Z-axis direction. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. Please be aware that. Please DO NOT fill in the PO Box address. California Warehouse: City of Industry, CA. New York State Warehouse: Perth Amboy, NJ. Georgia Warehouse: Austell, GA. North Carolina Warehouse: Grove NC. Oregon Warehouse: AIRPORT WAY Portland, OR. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. VEVOR is a leading brand that specializes in equipment and tools. Along with thousands of motivated employees, VEVOR is dedicated to providing our customers with tough equipment & tools at incredibly low prices.