The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Please contact our customer service team immediately if: 1. You changed your mind and wish to request a return. Your product was damaged during transit. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. The item “Power Feed X-Axis 150 LBS Torque Power Table Feed Milling Machine For Bridgeport” is in sale since Thursday, July 9, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “fansdealonline” and is located in Westbury, New York. This item can be shipped to United States.

• Brand: FANSDEALONLINE
• Model: AS-250
• MPN: ZY8LX00361
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″

SERVO 3 Axis CNC Knee Mill. This machine originally came with SERVO-II cnc system, it’s made by SERVO 20 years ago. We recently rebuilt this CNC knee mill. We installed new CNC control, servo motors/drivers and VFD. We reduced the price. We would also look at any reasonable offer! Brand new SERVO ORION servo motors for X, Y axis and Z axis(servo motor drivers the quill as Z axis). SERVO power feed for knee feed. Precision grounded ball screws for XYZ axis. 220v 3ph, HITACHI VFD for spindle motor, speed up to 5000 rpm. Table size: 10 x 52 (inch). Feed rate: 95 IPM. Home switches and limit switches for X/Y and Z axis. Limit switches for knee power feed. GSK980 CNC controller, one of most reliable CNC controllers on the market. USB port and RS232 interface available for data transfer. NEED PARTS FOR YOUR BRIDGEPORT? WE STOCK ALL BRIDGEPORT SERIES I REPLACEMENT PARTS! We are a distributor for HIGH QUALITY TOOLS, Inc. And carry their complete line of replacement parts and accessories. We also carry cutting tools, work holding, tool holders, measuring tools and much much more. New inventory being added regularly! Thank You for looking! We always try to improve our customer service to ensure that you, the customer , receive best service available! Just let us send you updated invoice. We guarantee that the items are exactly as stated in the description. The item “SERVO 3 AXIS KNEE MILL, NEW CNC AND SERVOS, BALL SCREWS, NEW VFD, POWER DRAW BAR” is in sale since Wednesday, February 6, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “toolguys2″ and is located in Eastlake, Ohio. This item can be shipped to United States.

• Country/Region of Manufacture: United States
• MPN: KNEE-MILL
• Country of Manufacture: United States
• Brand: Servo