Indexable Face Mill Cutter 90 Degree 3 x 1 inch 7 Flute APMT APKT CNC Insert. 3 Pounds Rough Estimation. Suitable For Most Face Milling Applications. Setting Angle: 90 Degree. Number Of Flute: 7. Cutting Diameter: 3 Inch. Arbor Hole: 1 Inch. Insert Size: APKT 33.

Servo Type 140X POWER FEED, 140 INCH POUNDS OF TORQUE. Milling Machine Power Feed: 140 in/lb Max Peak Torque, 90 in/lb Max Continuous Torque. Type 140 – Knee, Table, and Cross Feeds. Semi-automated machining on Class 1 mills to 3 hp. Peak Torque (half-wave series motor): to 140 in. / 15.8 NM torque. Intermittent Torque: 105 in. / 11.9 NM. Continuous Torque: 90 in. / 10.2 NM. 75-25 IPM / 19-635 mm/min (table & cross). 5-12 IPM / 13-305 mm/min (knee). 35 IPM / 889 mm/min (table & cross). 12 IPM / 305 mm/min (knee). Gear Reduction Ratio (motor to screw shaft): 72:1. Helical gearing and torque limiting friction safety clutch with new and improved gear. Electrical: 110V, 50/60 Hz, 2.5A. / 6.8 kg.

Servo Type 350X Power Feed MADE IN THE USA! Below is a list of our newest innovations. Brushless DC motor (BLDC) provides greater efficiency and increased reliability. Continual monitoring of limit switches/E-Stop status, motor speed, voltage, and current using microprocessor technology. Produces a minimum of 350 inch/pounds of. Torque as low as 0.3 inches/minute feed rate. This unit replaces our previous Type 140/150/200, resulting in one power feed that can be used on all three axes. Shop-tested performance proves superior to the legendary “Bridgeport” 6F/8F power feeds. Extremely accurate speed regulation under varying load conditions, as well as dynamic braking for quick stops. Dual voltage capable with an internal connector position change on the circuit board, plus an extremely wide input voltage range (90vac to 145vac) and high voltage selection (195vac to 250vac), resulting in stable operation during power fluctuations. Utilizes 75% less current under the same operating conditions than the present industry standard brushed DC motor designs. Drive gear changed from Delrin to hard coat anodized 7075 aluminum for extreme reliability and ability to handle the high torque loads. Safety overcurrent protection has been added to the motor/gear drive circuit. No more stripped gears. The ability to easily convert the unit from a table feed to a knee feed. Only power feed on the market with a safety E-Stop button. The limit switches no longer have line voltage (115vac) through them, they now have 5vdc which is much safer in case of cable damage or cuts. No risk of electrical shock. Safety logic circuitry to prevent accidental operation after an emergency stop, or during power up. The power feed will not operate after the E-Stop is released if the direction handle is either in the left or right position. Letting you know you can now operate the power feed either right or left direction. NEED PARTS FOR YOUR BRIDGEPORT? WE STOCK ALL BRIDGEPORT SERIES I REPLACEMENT PARTS! We are a distributor for HIGH QUALITY TOOLS, Inc. And carry their complete line of replacement parts and accessories. For all of your Bridgeport and other knee-mill replacement parts needs. We also carry cutting tools, work holding, tool holders, measuring tools and much much more. New inventory being added regularly! Thank You for looking! We always try to improve our customer service to ensure that you, the customer , receive best service available! Just let us send you updated invoice. We guarantee that the items are exactly as stated in the description.

Please take advantage of the zoom feature on the photos to judge cosmetics for yourself. All photos are part of the description and were taken from our own products. What you see in the photos is what exactly you receive. If it’s not pictured it’s not included. (Excluding weekends and holidays). Will apply for all. PO boxes, APO, DPO or FPO zip code. Note to Buyers: All the content of the description have been written base on the facts and our best knowledge. Mistakes may happen and might go above and beyond to resolve any issues. We always reply within a few hours. It barely exceed 24 hours to respond. If you receive an item and there is something wrong or you think it’s not Authentic, please don’t worry because you are 100% protected by us! Just send us a message which goes a very long way. We will respond and resolve any issue very shortly. We have passion to serve and give more service to customers, just let us know.

Sunnen MB770 5 Inch 3 Jaw Chuck with mandrel mount. What you see is, what you get. Please, due diligence’ to be sure these are the appropriate number you need. We are an actual business [58yrs] in automotive repair and machine shop. That specializes in engine rebuilding. So there has been a LOT accumulated, over the years. We only post what we have in stock! And every effort is put in to make sure the information is posted is correct.

HFS (R) 6 Inch Compound Slide Table CNC Table Precision Milling Machine Worktable Drill Vise Fixture Working Table. [Milling Machine Table Size]: 5.7 x 12.2(inches); T slot width: 0.6 inches; T slot spacing width: 2.5 inches. The longitudinal travel of the table is 5.1 inches, and the lateral travel is 6.6 inches. [Material]: Built by heavy-duty cast iron material. [Premium Quality Structure]: Trapezoidal thread spindle can be precisely adjusted; precise scale for better work; 2 chip flutes on the working surface. [Wide Application]: This milling working cross table machine is great for mounting on drilling machines for precise positioning. It can be used for most types of milling and drilling, ideal for all drill stands, drilling, and milling machines. Orders over a certain dollar amount will be insured and sent signature required. CANCELLATION NOTICE: Please be sure your address is correct before placing your order!

OEM Quality Acme Cross feed Screw made as a replacement for Bridgeport Milling machines with 12 inches of y axis travel. Lead is 5 turns per inch.

Milling Machine Vise Used 6 Inch Bearing Screw Nut For BRIDGEPORT Mill Parts. Applicable models:milling machine.

Devlieg 2.5 model 2b-36 spiramatic jig mill S/N 8384 with dro-magnetic 3 axis digital readout. Harbert-Devlieg 2.5 inch model 2b-36 with anilam 3 axis digital readout.

BULLARD 54 INCH VTL MAN AU TROL VERTICAL TURRET LATHE. LOADED ONTO CUSTOMERS TRUCK PLEASE CALL JIM FOR MORE.