Mainly used for side milling and face milling. Ø 2mm to 16mm. 45 Degree 60 Degree. Angle: 45 Degree, 60 Degree. Applicable machines: CNC machining center, engraving machine and other high-speed machines.

Removed from a semiconductor inspection machine made in Japan. Incredibly heavy, this structure was made to suspend heavy moving fixtures without flexing.

End Milling Cutter Steel Right Angle Shoulder Disc CNC Lathe Machining Center. Precaution for using cutting tools. Precariousness: Direct touch to a sharp cutting edge may cause injury. Countermeasures: When you set up tools to the machine or take tools out of the case, please wear protective gloves. Precariousness: Misuse or inappropriate working conditions may cause tool breakage or dispersion of broken pieces. Countermeasures:Please use safety item, such as safety glasses and protective gloves. Please use in the range of our recommended cutting condition. See our catalog or instruction manuals. Precariousness: Excessive impact or heavy wear will increase cutting resistance and may cause tool breakage and dispersion of broken pieces. Countermeasures: Please use safety item, such as safety glasses and protective gloves. Early exchanging tools is preferable. Precariousness: Dispersion of heated or prolonged chips may cause injury or burn. For chips removal, please stop the machine beforehand and use safety items, such as safety glasses and protectives gloves. Precariousness: Tools and materials reach high temperatures during cutting operation. Direct touch to the tools and materials shortly after cutting may cause burn. Precariousness: Sparks, generation of heat or chips in high temperature during operation may cause file. Countermeasures: Please do not operate around Hazardous zone, in which there is some possibility of fire or explosion. In case of using oil-coolant, please make sure there is sufficient fire-protection equipment. Precariousness: Lack of dynamic balance during high-speed revolutions leads to vibrations which can make the tool break. Please conduct test-operation before cutting, and confirm that there is no vibration or unusual sound. Precariousness: Direct touch to the burs which were generated on the rough surface of the workpiece may cause injury. Countermeasures: Do not touch the workpiece with bare hand. Precariousness: If the insert or other tool parts are not installed properly, they can fall down or break which may cause injuries. Countermeasures: Please clean up insert pockets or clamping parts before setting insert. Please set up inserts with supplied wrench only, and confirm that the inserts or parts are clamped completely. Never use inserts or parts other than those prescribed. Precariousness: If inserts are clamped too tightly by supplementary tools like pipe etc. Inserts or body may break. Countermeasures: Do not use aids such as pipes. Please set up using supplied wrench only. Precariousness: When tools are used in high-speed revolution, inserts or parts may burst out of the body due to centrifugal force. Countermeasures: Please use in the range of our recommended cutting condition. Accuracy and balance of machine spindle should be checked and adjusted regularly to prevent wear of the bearing due to eccentric rotation. Milling Cutters and other Cutting Tools. Precariousness: Since milling cutter have sharp edged, direct contact with bare hands may cause injury. Precariousness: If a cutter lack balance, the tool can start to vibrate. The dispersion of broken piece can cause injuries. Precariousness: When drilling a through-bore, it is possible that a disc is created during the drilling procedure that can fly out of the workpiece at a high speed. This is very dangerous since the disc has sharp edges. Countermeasures: Please use safety items, such as safety glasses and protective gloves. Also attach a cover on a chuck part. Precariousness: Dispersion of falling down of broken inserts may cause injury. Countermeasures:Please Check that the cutting inserts are brazed firmly before use. Please do not use brazed tools in the condition that requires high cutting temperature. Precariousness: If Brazing is carried out many times, the strength of carbide insert is deteriorated and can break easily during cutting. Countermeasures: Please do not use tools that have brazed several times. The quality of the tool deteriorates. Precariousness: The tools can only be used for the appropriate application. It may damage tools and machines. Countermeasures: Please follow our recommended usage for the tools. There may be some delays due to flight, holiday, weather, local post, local natural disaster impact. It must also be in the original packaging.

Metal Boring Head Lathe Bar Hex Wrenched Durable Steel Milling Machine Tools. F1 Boring Head excludes tools and tool holders. 12mm-9pcs tool excluding F1 boring head and tool rest. BT40 tool rest does not include F1 boring head and cutting tools. There may be some delays due to flight, holiday, weather, local post, local natural disaster impact. It must also be in the original packaging.

These vise jaws are made with versatility in mind. First reversible and stackable jaws. Talongrip and Veregrip in one. One side is for Talongrip and the other is for Versagrip. Recommend MiteeBite #33050 Talon Grip clamps, #33030 stop VersaGrip #32175 (NOT included). Made out of stress relieved 1018 steel. 8″ pairs extend your 6″ vise to 8 of clamping width. Allows edge griping on 0.060. Black oxide to prevent rusting. AB Workholding side low profile stop with 6-40 screws are included. For large production setup and expanding your vice capacity. 75 shafts not included. Holds large material stock with built in stop and allows you to mill and drill thru without risers and cutting into the vise steel jaws. 2.9 lbs each. Set is for 3.

HV6 /150 mm /6 Inches-4 Slots Rotary Table & Steel Dividing Plates Set with Free Manual-Milling Indexing Kit. Rotary table’s Overall Height : 80 mm (3-1/4) Centre Height in Vertical Position: 105 mm Worm- Gear Ratio- 1:90, which means that the 1 handle rotation shall turn the table by 4 Degrees. Table Graduated 360 Degrees, Resettable Dial & Handwheel graduated in seconds. Vernier scale is caliberated to 10 seconds. Quality Adjustable Tailstock for HV4/ HV6 Rotary Table. Alloy Steel Hardened & Ground Point Center. Minimum Center Height 80 mm & Maximum Center Height is 105. Set of 3 dividing plates designed to fit this HV6 Rotary Tables is included in the kit. Centre Hole of the Plate is 21 mm No. Of Holes in each Plate Plate A- 15, 16, 17, 18, 19, 20, Plate B- 21, 23, 27, 29, 31, 33 Plate C- 37, 39, 41, 47, 49 It is supplied with a brass stopper key, Bracket, Crank Handle & fixing screws. Vices & work Holding. Jewelry & Watch Making. Do It Yourself (DIY Tools). HSS Cutting & Finishing Tools. HV6 150mm 6/4 Slots Rotary Table, Adjustable Tailstock, Steel Dividing Plates Set. Pls note :- 1/. It is important to note that after the pandemic, although the logistic services have been improved a lot. However, they are still to reach their original positions. We expect our customers to understand and support us in such issues which are unforeseen and not in our control. However, we take complete onus and responsibility of supplying you a completely brand new product without any manufacturing or transit damage. Though we packed our goods with utmost care and strong packaging material, since our products are heavy in weight, there could be transit damage in a few cases. However it has been seen that such issues are not always a problem and our customers could still use them. In majority of the cases, we have experienced that we manage to resolve the issue amicably without any trouble. So a discussion is the best way of a desired resolution. Listing and template services provided by inkFrog.

End Face Milling Cutter Holder Steel Durable Housing Adapter CNC Machine Parts. Product Name: Face Mill Tool holder. Overall clamping Precision: 0.010.015mm. Product Precision: =0.005mm. Material: High Quality 20CrMnTi Steel. True roundness: 0.8 u. Carburizing depth: 0.8 u. Surface roughness: 0.8 u. Standard speed: =10000 RPM. This product is suitable for all products of D size in the dimensional drawing. Manual measurement may have errors, please understand! Note: If the 45L product is out of stock, products of other lengths will be sent by default. The product is made of High Quality 42CrMnTi Steel and processed by the current advanced quenching and hardening technology to make the product harder, more concentric, and improve work efficiency. The accuracy of the product is 0.005mm, and the accuracy of the whole assembly is 0.010.05mm, which can help you complete the production of high-quality products. There may be some delays due to flight, holiday, weather, local post, local natural disaster impact. It must also be in the original packaging.

Item Description: Set 8 Pcs DP6, DP8, DP10, DP12, DP16, DP18, DP20, DP22 PA14-1/2 #1-8 Involute Gear Cutters Model: DP10, DP12, DP16, DP18, DP20, DP22, DP24(Inner Bore 22mm) DP6, DP8(Inner Bore 27mm) pressure angle: 14.5° degree Outside Dia: 55mm Inner Bore: 22mm /27mm Material: HSS No1 :Z1213; No2 :Z1416; No3 :Z1720; No4 :Z2125; No5 :Z2634; No6 :Z3554; No7 :Z55134; No8 :=135. 1 Set x Involute Gear Cutters. Note: Please allow 0.1- 0.5 cm error due to manual measurement. The colors may have different as the difference display, please understand. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “otosmile” and is located in this country: CN. This item can be shipped worldwide.

• Model: DP6
• Brand: Unbranded
• Function: Milling
• Machine Type: Milling Machine

Item Description: Set 8 Pcs DP6, DP8, DP10, DP12, DP16, DP18, DP20, DP22 PA14-1/2 #1-8 Involute Gear Cutters Model: DP10, DP12, DP16, DP18, DP20, DP22, DP24(Inner Bore 22mm) DP6, DP8(Inner Bore 27mm) pressure angle: 14.5° degree Outside Dia: 55mm Inner Bore: 22mm /27mm Material: HSS No1 :Z1213; No2 :Z1416; No3 :Z1720; No4 :Z2125; No5 :Z2634; No6 :Z3554; No7 :Z55134; No8 :=135. 1 Set x Involute Gear Cutters. Note: Please allow 0.1- 0.5 cm error due to manual measurement. The colors may have different as the difference display, please understand. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “llucky666″ and is located in this country: CN. This item can be shipped worldwide.

• Model: DP8
• Machine Type: Milling Machine
• Apply to: For high speed steel
• Type: Gear milling cutter
• material: HSS
• Quantity: 8Pcs(No1-8)/Set
• Pressure angle: 14.5° (degree)
• Outside Dia: 55mm
• Inner Bore: 22mm /27mm
• Brand: Unbranded
• Function: Milling