Sign up to Newsletters. Feed 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage: 110 V, 60 Hz. Rotate speed: 0-200 rpm. Length: 33 cm (13 inch). Width: 20 cm (7.9 inch). Height: 18 cm (7 inch). Gross weight: 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. International Buyers Please Note. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within 12-24hours. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Westminster Hwy, Richmond, BC, Canada. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machine 0-200 RPM” is in sale since Wednesday, December 11, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “hotitemsale” and is located in Richmond. This item can be shipped worldwide.

• Brand: VEVOR
• MPN: 74AZY00331523585124
• Model: AS-250-150
• Power Source: Electric
• Voltage: 110 V, 60 Hz
• Control: See description
• Function: Milling
• Machine Type: Milling Machine
• Type: X-axis
• Torque: 150lbs
• Rotate speed: 0-200 rpm

The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. We have Four warehouses located in CA, NY, NJ & GA. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. The item “X-Axis 150 LBS Torque Power Feed For Bridgeport Vertical Milling Machine 200 RPM” is in sale since Wednesday, September 23, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “homesupplies01″ and is located in Westbury, New York. This item can be shipped to United States.

• Voltage: 110V
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″
• Gross weight: 6.5 kg(14.3 lb)
• Warranty: 5 Years
• Function: Milling
• Machine Type: Milling Machine
• Power Source: Electric
• Control: Manual
• Brand: VEVOR
• Model: AS-250-150
• MPN: ZCXZG0085

The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. We have Four warehouses located in CA, NY, NJ & GA. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. The item “X-Axis Power Feed for Vertical Milling Machine 150 Lbs Torque Knee Mills Fits” is in sale since Thursday, July 16, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “homesupplies01″ and is located in Westbury, New York. This item can be shipped to United States.

• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″
• Gross weight: 6.5 kg(14.3 lb)
• Warranty: 5 Years
• Machine Type: Milling Machine
• Power Source: Electric
• Function: Milling
• Control: Manual
• Voltage: 110V
• Brand: VEVOR
• Model: AS-250-150
• MPN: ZCXZG0085

This is an Original Bridgeport 6F power feed for the X-Axis. Gears work smooth both directions. Included: Shift Handle, Lead Screw Coupling, Crank Handle, Electronic Circuit board. Normal scratches and scrapes for its age. See photos for included items and condition. This is an Untested unit. The unit is missing the Graduated Dial & power cord. The item “6F Power Feed for X-Axis on Bridgeport milling (mill) machine Powerfeed” is in sale since Thursday, October 29, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “larrdog” and is located in Agoura Hills, California. This item can be shipped to United States.

• Country/Region of Manufacture: United States
• Machine Type: Milling Machine
• MPN: 6F
• Brand: Bridgeport
• Voltage: 110 V

Sign up to Newsletters. Brand New AL-310S X-Axis Power Feed Kit For Milling Machine. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AL-310S X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). To stop jog operating, you must first turn FEED KNOB to 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Brand new power feed. X traverse (left-right travel). Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Rotate speed: 0-200 RPM. Max torque: 450 in-lb. Max feed rate: 650mm/min. Max return speed: 850mm/min. Dimension: 8 x 4.5 x 13 inches. Package size: 11.8 x 8.7 x 13.8 inches. Gross weight: 16.5 lbs. 1 x Power Feed For Milling Machine. 8 x Adjustable Pad. 2 x Tiavel Stop Assembly. 1 x Bevel Gear. 1 x Dial Nut. 1 x Locking Nut. 1 x Product Manual. Power Feed Milling Machine. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. California Warehouse: City of Industry, CA. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “AL-310S X-AXIS Power Feed Milling Machine 450in-lb peak 0-200RAL-310S Bridgeport” is in sale since Wednesday, August 2, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “prettystylesoul” and is located in Houston, Texas. This item can be shipped to United States, all countries in Europe, Canada, Mexico, Australia.

• Brand: VEVOR
• MPN: gdg7800132
• Model: AL-310S
• Power Source: Electric
• Voltage: 110V, 50/60Hz
• Control: Manual
• Function: Milling
• Machine Type: Milling Machine
• Rotate speed: 0-200 RPM
• Max torque: 450 in-lb
• Max feed rate: 650mm/min
• Max return speed: 850mm/min
• Dimension: 8 x 4.5 x 13 inches
• Gross weight: 16.5 lbs

The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Please contact our customer service team immediately if: 1. You changed your mind and wish to request a return. Your product was damaged during transit. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. The item “Power Feed X-Axis 150 LBS Torque Power Table Feed Milling Machine For Bridgeport” is in sale since Thursday, July 9, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “fansdealonline” and is located in Westbury, New York. This item can be shipped to United States.

• Brand: FANSDEALONLINE
• Model: AS-250
• MPN: ZY8LX00361
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″

X-Axis Power Feed 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage: 110 V, 60 Hz. Rotate speed: 0-200 rpm. Machine Type: Milling Machine. Package size: 332018 cm (137.97 in). Gross weight: 6.5 kg(14.3 lb). 1 x AS-250-150 X-Axis Power Feed for Milling Machine. 1 x Set of Necessary Accessories. 1 x Product Manual. Power Feed Milling Machine. Sign up to newsletter. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. California Warehouse: City of Industry, CA. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “AS-250 150Lbs Torque Power Feed Milling Machine X-Axis 110V Bridgeport 0-200RPM” is in sale since Wednesday, October 18, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “bestfashionitem” and is located in Hebron, Kentucky. This item can be shipped to United States, Canada, Mexico, Germany.

• Brand: VEVOR
• MPN: FRCXZ00945
• Model: AS-250
• Power Source: Electric
• Voltage: 110 V
• Control: Manual
• Function: Milling
• Machine Type: Milling Machine
• RPM: 0~200
• TORQUE: 150LBS
• Gross weight: 6.5 kg(14.3 lb)

Made of aluminum material. Rotate Speed: 200 RPM, Max Torque: 450in-lb. 7 x 3.5 x 12inc. QUIET & RAPID OPERATION. With speed adjust knob, speed can be adjusted according to operator’s requirement, ranging from 0-9. Jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. DURABLE & LONG LASTING. Safe design helps to protect transmission gear and electronic components; accessories of this power table feed will not mesh and wear at the same spot, maximizing durability and longevity. Power feed is equipped with safety feature to protect transmission gear and electronic components as to meet the requirements of ergonomics. Small volume and easy installation, noiseless direction changes. Fit almost any horizontal knee type milling machine and other small machinery. Milling Machine Power Feed. Power Feed X-Axis, Voltage: 220V, Rotate Speed: 0-200 RPM, Max Torque: 450 in-lb, Dimension: 9 x 4.5 x 14 inches. Rotate Speed: 0-200 RPM, Max Feed Rate: 650mm/min. Milling machine power feed features noiseless direction changes and direction control knob for easy and rapid operation. Equipped with several necessary accessories, this not only increases durability and longevity but even reduces noise over time. Power table feed won’t vibrate or strain in low speed. This small volume and easy installation X-axis power feed is designed to automate the feeding process on Bridgeport type milling machines. Suitable for horizontal installation models including turret milling machine, drilling and milling machine and other small machinery. Power Feed Milling Machine With Rotate Speed. If you want to get the most out of your milling drilling machine you really need a power feed. This power feed comes with everything required to start milling with exact contro. Our brand new Mill Power Feed featuring Max. Rotate speed 200Rpm, power torque 450 in-lb, is for bridgeport and similar knee type milling machines. Quiet & Rapid Operation. Durable & Long Lasting. Rotate Speed: 0-200 RPM. 1 x Power Feed Milling Machine. 1 x Necessory Accessories. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. California Warehouse: City of Industry, CA. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. Caifornia Warehouse: 18501 Arenth Ave, City of Industry, CA 91748. 300 W Airtex Blvd, Suite 200, Houston, TX 77090. 2125 Gateway Blvd, Hebron, KY 41048. 1000 High Street, Perth Amboy, NJ 08861. The item “Power Feed X-Axis 200RPM 450in-lb for Bridgeport Type Milling Machine 220V” is in sale since Monday, February 17, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “digitalzoneproduct” and is located in Rowland Heights, California. This item can be shipped to United States, Canada, Mexico.

• Brand: VEVOR
• MPN: GFSAZ007481574753692
• Power Source: Electric
• Voltage: 220V
• Material: Aluminum
• Rotate Speed: 0-200 RPM
• Max Torque: 450in-lb
• Dimension: 7 x 3.5 x 12inches (17x9x30cm)
• Package Content 1: Power Feed Milling Machine
• Package Content 2: Necessory Accessories

X-Axis Power Drive Feed Kit for Warco Milling Machines VMC, WM20 & VSE Single Phase UK mains 220/240 volt model Excellent Quality Unit. Specifications = Model = AL-310S-XW 220/240 volt model (UK). Torque = Normal = 135in-lb /11.25ft-lb. Maximum = 450in-lb = 37.5ft-lb. Genuine Power unlike others state! Forward/Reverse with 1.5 sec delay Variable speed control = 0 to 140 rpm Fast speed push button = 200 rpm Table Safety limit switch & fittings Overload cut breaker protection package weight = 7kg Fits Warco VMC with extended 15.9mm – 5/8 Diameter Lead-Screw End Easy Fit Kit = you need to Drill 2x 5mm Holes & Tap with 6x1mm tap Please Note. Telephone contact number is required when ordering for Courier. The item “X-Axis Power Drive Feed Kit for Warco VMC, WM20, VSE Milling Machines UK-240volt” is in sale since Wednesday, April 26, 2017. This item is in the category “Business, Office & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “wtv-uk” and is located in Norfolk. This item can be shipped worldwide.

• MPN: AL-310S-XW
• Brand: ALSGS

American Business ALL ITEMS IN STOCK IN CALIFORNIA. American STANDARD PRODUCTS QUALITY GUARANTEED. AS-250 150Lbs Torque Power Feed Milling Machine X-Axis ALSGS 0-200RPM. WHY SHOP WITH BLTPRESS? Item was as described and arrived quickly. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). AS-250-150 X-Axis Power Feed for Milling Machine x 1. Set of Necessary Accessories x 1. Product Manual x 1. All items are dispatched from our warehouse in HACIENDA HEIGHTS, CA. Some products may be dispatched in more than one carton. International Buyers – Please Note. If you have a problem with the product. We will require a picture of the damaged part for verification. The item “AS-250 X-Axis Torque 150 in-lb Power Feed Milling Machine 200PRM For Bridgeport” is in sale since Saturday, March 2, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “bltpress” and is located in Hacienda Heights, California. This item can be shipped to United States.

• Brand: bltpress
• Model: AS-250
• MPN: ZY8LX00361
• Voltage: 110V, 50/60Hz
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13″x8″x7″