ACER “e” Series Bed Mill, 14″ x 54″ – e-1454B. Standard Accessories for the e-1454B Bed Mill. Tool box with tools. CAT or BT #40 drawbar (NST optional). Operation manual with parts manual. Leveling pads & screws. 5 HP inverter motor with fan cooling system that dissipates heat efficiency. Extra oilers to lubricate the high-low moving device and to oil the quill. One piece quill pinion & shaft. Precision hardened & ground slideways. Precision ground C5 ball screws. Precision ground guide line to 0.0002. Turcite-B coated saddle ways. Grease fitting for lubricating bull gear. CNC & operator console. Hand scraped saddle ways. X, Y and knee axes are hardened and ground to HRC 52 degrees. Drives & accessories cabinet. Hardened & ground table top to HRC 52 degrees. 230V / 460V three phase ready and available to run at single phase 230V when specified. We are liquidating a machine shop with tons of great tooling. So far we have only listed a fraction of the items for sale. We still have to go thru several warehouses as well. The property has 100′s of chucks, tables, spacers, indexers and carts and carts of tooling. Racks and Racks of Cat 50, cat 40, cat 30 and many others. Racks and Racks of face mills (sorry no carbide) and other tooling. You can expect we have most everything that goes into a typical machine shop. Over the next couple of weeks we will be listing tons of new chucks. If you are looking for a particular size let us know and we probably have it and can make a deal and will design a special ad for you. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “howfactor” and is located in this country: US. This item can be shipped to United States.

• Model: Acer E-1454B CNC
• Function: Milling
• Brand: Acer
• Control: CNC

For more information on our products. Please send message to us. AS-250 150Lbs Torque Power Feed Milling Machine X-Axis ALSGS 0-200RPM. What Customers Have To About Us. ” Delivered as promised and item is as described “. Just what i was looking for. Had a problem-was able to successfully resolve it. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). 110 V, 60 Hz. 33 cm (13 inch). 20 cm (7.9 inch). 18 cm (7 inch). 6.5 kg(14.3 lb). AS-250-150 X-Axis Power Feed for Milling Machine. Set of Necessary Accessories. X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. All items are dispatched from our warehouse in HACIENDA HEIGHTS, CA. Some products may be dispatched in more than one carton. International Buyers – Please Note. If you have a problem with the product. We will require a picture of the damaged part for verification. We offer detailed product descriptions and images to give you a real advantage in finding the products you’re looking for. 25 years Industry Experience. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “super-hypress” and is located in this country: US. This item can be shipped to United States.

• Brand: SUPER-HYPRESS
• Model: AS-250-150
• MPN: ZY8LX00361
• Voltage: 110V
• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13\
• Gross weight: 6.5 kg(14.3 lb)
• Warranty: 5 Years
• Function: Milling
• Machine Type: Milling Machine
• Power Source: Electric
• Control: Manual
• UPC: 980610788829