Dividing Head Indexing Foot Rest Tail Stock. Please ask questions and specific size to be sure it fits your machine. Has a centerline of about 5″ to 6″. In very good condition. You can clean it up a bit to make it look nice.

Stand is not included in listing, please check our other listings if you need the stand. This machine uses 220V Standard Power! Highlights Of This Machine that set it apart from others on the market. MUCH Larger Travels and work area. Quill DRO Included Standard (This is for the spindle up/down movement). 3 Bolt Head Mount is now standard (where the head mounts to the Z Axis), for more rigidity when milling – Much improved over the single bolt mount type. Main Z Axis Column is attached to the base with 4 bolts, and mounted from the top, with a wide, proper. Mounting surface for much more rigidity over other models in this size range. 001? Readings with larger dials on the X and Y axis, with true 10 Thread Per Inch Leadscrews make it. Easier to cut accurately – One line on the dial is. 001? , one full turn of the handwheel is. 100? , much easier to use than those with odd metric conversions. 50-3000 RPM variable speed with the turn of a knob, properly set up with Low and High for a wider speed range, and plenty of power at lower speeds. Precision ground ways for smoother movements – Not just rough milled. Thrust Bearings in leadscrew ends – not bushings – Much smoother movements and less backlash. Split nuts on X and Y Axis to allow for backlash adjustment. DC BRUSHLESS MOTOR, Variable Speed, POWERFUL, SMOOTH, and RELIABLE. Belt Drive from Motor to Spindle runs MUCH quieter than others, and eliminates any. Failure prone plastic gears (And the hassle of changing them when stripped). Variable Speed with Belt Drive and Brushless DC Motor. Average time delivered is 2-7 days depending on how far from Pittsburgh you are, it could be a little longer in remote places but normally is very fast. 1060 Montour West Industrial Park. We are machinists here too, so we know what we sell. This is really a top quality machine, and will last a long, long time. AND we are here for support too. We sell these machines regularly, we know them inside and out, and have been in business for many years, so if there is any question, we can help. PM30MV (DC Brushless Motor, and Belt Drive Head is Standard). End Milling Capacity 3/4? Face Milling Capacity 3-1/2? Table Size 8-1/4? X 33? Cross Travel (Y Axis) 8-3/4? Longitudinal Travel (X Axis) 23? Table Leadscrew Pitch 10 TPI. Vertical Travel (Z Axis) 14? Max Distance Spindle to Table 17? Taper of Spindle R-8, w/7/16-20 Drawbar Thread. T Slot Size Actual size 14mm, our 9/16? Kit listed is sized for this machine. Range of Spindle Speeds 50-3000 rpm, 2 Ranges (Properly set up with high and low range belt positions for more power at lower speeds as it should be). Headstock Tilt Left & Right ±90°. Net Weight (Not Including Base) 530 LBS. Net Weight (With Base) 605 LBS (630 LBS with base w/leveling feet). Country or Origin: China. Power Required 220V, Single Phase, 10 Amp. Cord Connection/Type: Cord approx. 5′ length, User to supply plug needed for your outlet 20A 240V With Ground, No Neutral Required. Optional Stand Height: 28? (Base w/leveling feet 32?) Bolt Pattern, Machine Base Mounting Holes: APPROX. 13-1/8″W x 15″ Front to back, with 1/2? Holes. (we recommend waiting until your machine arrives before drilling any mounting holes in case this varies) Table Surface Height (On Stand): 36? (with base w/leveling feet 40?) Height, Head at normal working height (W/O Stand): 39″ Max Height, Head at top of travel (W/O stand): 48″ Height, Head at normal working height (On Stand): 67″ (on base w/leveling feet 71?) Max Height, Head at top of travel (On stand): 76″ (on base w/leveling feet 80?) Width, Tip to Tip of table handles: 46-1/4″ Dimension Front To Back, from back of chip pan, to front table handle tip: 31″ (Can be pushed back against a wall, and table handle tip will be 31 from wall). NO extra charge for residential or anything on these, as long as a truck can get to you, its covered. If you have ANY questions, feel free to message us. Check out our other auctions for more lathes and mills.

TECHNO ISEL DAVINCI CNC ROUTER/PROTOTYPING MILL KRESS ROIUTER W/ SAFETY ENCLOSURE. THIS UNIT IS IN GOOD WORKING CONDITION (COMPUTER/SOFTWARE NOT INCLUDED). COMES WITH EXTRA COLLET, ROUTER WRENCH, & DUST COLLECTING SHOP VAC. THIS UNIT IS OFFERED FOR SALE AS PICTURED. Size of unit : 32″ x 45″ x 66 (L x W x H). GREAT DEALS EXPORT WHOLESALE AUCTIONS.

100% MADE IN TAIWAN. (No stand is included in this listing, if you would like a machine with the stand, please see our other listing). This machine uses 220V Power! Highlights Of This Machine. Very High Quality Milling Machine, 100% Made in Taiwan. Built For Those Users Who Are Looking For Higher Quality In A Dovetail Type Mill Configuration. Very Large Y and Z Travels Compared With Other Models In This Class, over 11? Of Y axis Travel. One Shot Lube System Standard. Very High Grade Castings Used Throughout Machine. Head Swivels 90 degrees Left and Right for angled milling / drilling operations. Hand Scraped way Surfaces for better oil retention and fit, which leads to ultra smooth. One Shot Lubrication system is standard equipment, which also extends machine life, and. High precision Inch Pitch lead screws, for ease of use and greater accuracy (10 TPI Screws). High Precision Spindle with +/. 0002 or less runout for greater tool life and accuracy. Balanced gears in head for smooth and quiet operation, Hardened and Precision Ground for long. Life, and extremely quiet running for a geared head machinE. Precision Honed Quill Bore for tighter tolerance fit, which leads to improved accuracy when. Drilling and precision boring. The Quill is Precision Ground, for higher accuracy. No belts to change, simply stop and move levers for speed changes, quick and easy. Tolerance Test check, each machine is checked for accuracy through a careful inspection. That exceeds their expectations. Question 2: Is there any other difference in the machines, besides what is described above? All accessories such as power feeds, stands, DRO, etc. Are the same between both models. Answer 3: It really depends what you are doing or think you will be doing. The 833T is still fine with cutting Aluminum and similar materials, no problem with that, you just have a lower spindle speed, so you may just have to go a little bit slower with feed rates, but it will still do the job just fine. So the 833T-V is a better choice if you are doing more higher speed aluminum cutting and want to get maximum feed rates, but it still has plenty of power at lower speeds for any type of general purpose work in steel, stainless steel, cast iron, etc. Just not quite as much power as the 833T at lower speeds. Either machine can do any materials that you can machine on a mill just fine, some things are just more suitable for one of the particular models. Table T Slot Size / Spacing Between. Z Axis Travel (Head). Distance, Spindle to Table. 4-3/4, 2.952? (75MM). Precision Ground ACME Leadscrew W/ Backlash Adjustments on. X and Y Axis. 100 (10 Threads Per Inch). High Precision Tapered Roller Bearings, Fully Adjustable. Overall Height, to reach Maximum top of Z Axis Travel. Height with head at normal working height. Height of Table Working Surface, mounted on optional stand. Front to back, rear of machine to front of Y Axis Handle. Chip Tray Size (At top of base). Width X Axis Table Handles, Tip to Tip. 900 LBS (Without Stand) 1030 (With Stand). 220 Volt Single Phase Power. NO extra charge for residential or anything on these, as long as a truck can get to you, its covered. If you have ANY questions, feel free to message us. Check out our other auctions for more lathes and mills.

TYPE PRECISION MILLING MACHINE. (No Stand is included in this listing). This machine requires a Standard 120V Power Supply! Variable Spindle Speeds, with a range from 40 to 3000 RPM, in 6 steps, allows you to perfectly match the speed for each job. Compact, Accurate, Economical Machine. Great for those who are looking for a. Compact machine for a smaller work shop, yet need the ability to take heavier cuts. Compared with other machines in this size range. Spindle is Supported by High Precision Tapered Roller Bearings. Mill Head May be Tilted ±90° (both left and right). Precision Manual Fine Down Feed is standard. Adjustable Tapered Gibs for longer life. Positive Locks are standard for Table, Head, Quill, and Column. Easy Reading Dials Have Satin Chrome Finish, Graduated in. Quill DRO is Standard, Accuracy of the Display 0.0005, Selectable from. Generous 18-1/4? Spindle To Table Max Distance for taller work. 8-1/2? Y Axis Travel, More than other machines in this class. 3 Axis DRO Installed. Note: if a 3 axis DRO is added to the machine, the 3rd axis of the DRO reads the HEAD up and down, Not the quill, so it is not doubling up on the measurement. If you add the 3 axis DRO, now both Z Axis movements are covered. Drilling Capacity: 1-1/4? Max. End Milling Capacity: 1? Max. Face Milling Capacity: 3? Table Size: 27-1/2? X 7-1/8? Cross Travel (Y Axis): 8-1/2? Longitudinal Travel (X Axis): 15? Table Leadscrew Pitch 10 TPI. 100? Per Turn Table Dial Graduations. 001? Vertical Travel (Z Axis): 16? Max Distance Spindle to Table: 18-1/4? Taper of Spindle: R-8, w/7/16-20 Drawbar Thread Spindle (Quill) Travel: 3? T Slot Size: 1/2? (T Slots are slightly less than 1/2? , actual size 12mm, our 1/2? Kit is sized for this machine) Range of Spindle Speeds: 40-3000rpm, 6 Steps, variable in each range Head Tilt: Left & Right ±90° Motor: 1.5 HP Net Weight (Not Including Base): 475 LBS Net Weight (With Optional Base): 575 LBS Power Required: 110/120V, 20A Circuit. 5′ cord, Includes 120V Plug with ground Dimensions (Assembled on stand): 39? W x 74? H x 30? D Height with head at top of Z travel: 80? (On Stand) Height with head at normal working height: 75? (On Stand) Optional Stand Height 32? Country of Origin: China. Machine Base Dimensions (Cast Iron Base of machine, where it sits on the chip pan) Approx. 13-1/2″Wx21″D Machine Base Dimension (Bolt Pattern) Approx. 11″Wx14-1/4″D Table Height, machine base (Where it sits on the chip tray) to table, approx. 8-1/2? Footprint of stand at floor, approx. 14-1/2? W x 21-1/4? Front to back. Average time delivered is 2-7 days depending on how far from Pittsburgh you are located. If you need liftgate service, please message us one you place your order to let us know. Quality Machine Tools / Precision Matthews Machinery Co. 1060 Montour West Industrial Park. We are machinists here too and have been in business for over 20 years. We know our machines and we know what we sell. So if there is any question, we can help.

TYPE PRECISION MILLING MACHINE. LISTING INCLUDES THE FOOTSTAND FOR THE PM25MV WITH 4PCS LEVELING FEET AND PADS INCLUDED! This machine requires a Standard 120V Power Supply! Highlights Of This Machine. Extremely Reliable, Brushless DC Variable Speed Motor Included Standard. Belt Drive Design, For Smoother, Quieter Running. Extra Large Column To Base Mount, Over 400% More Area, Makes A Much More Rigid Machine, Greatly Improved Over Other Machines In This Size Range. 3 Bolt Head to Column Mount is Standard, Also For Increased Rigidity. Runs in both Forward and Reverse, Good for Tapping. Larger Dials at Table Ends, Graduated in. 001, For Easier to Read, Accurate Table Movements. Leadscrews Are True Inch Pitch Screws (Not Metric Conversions Like Many), 10 Threads Per Inch. Variable Speed with Belt Drive and Brushless DC Motor. Installed 3-Axis DRO w/LCD Display. PM25MV (DC Brushless Motor, and Belt Drive Head is Standard). End Milling Capacity 3/4? Face Milling Capacity 2/1/2? Table Size 27-1/2? X 7-1/8? Cross Travel (Y Axis) 7? Longitudinal Travel (X Axis) 19? Table Leadscrew Pitch 10 TPI. Vertical Travel (Z Axis) 13? Max Distance Spindle to Table 13? Taper of Spindle R-8, with 7/16-20 Drawbar Thread. T Slot Size Actual size 12mm, our 1/2? Kit listed is sized for this machine. Range of Spindle Speeds 50-2500rpm, 2 Steps. Headstock Tilt Left & Right ±90°. Machine Height (Without Stand) 38-1/2. Stand Dimensions: 13-3/4? W x 16-3/4? D (Top surface where machine mounts). Net Weight (Not Including Base) 275 LBS. Net Weight (With Base) Approx. Country of Origin: China. Power Required 110/120V, Minimum 15 Amp Circuit Approx. 5′ cord with standard 120V plug included. Average time delivered is 2-7 days depending on how far from Pittsburgh you are located. If you need liftgate service, please message us one you place your order to let us know. Quality Machine Tools / Precision Matthews Machinery Co. 1060 Montour West Industrial Park. We are machinists here too and have been in business for over 20 years. We know our machines and we know what we sell. So if there is any question, we can help.

STAND INCLUDED WITH LISTING! This machine requires a Standard 120V Power Supply! Compact, Accurate, Economical Machine. Great for those who are looking for a. Compact machine for a smaller work shop, yet need the ability to take heavier cuts. Compared with other machines in this size range. Spindle is Supported by High Precision Tapered Roller Bearings. Mill Head May be Tilted ±90° (both left and right). Precision Manual Fine Down Feed is standard. Adjustable Tapered Gibs for longer life. Positive Locks are standard for Table, Head, Quill, and Column. Easy Reading Dials Have Satin Chrome Finish, Graduated in. Quill DRO is Standard, Accuracy of the Display 0.0005, Selectable from. Generous 18-1/4? Spindle To Table Max Distance for taller work. 8-1/2? Y Axis Travel, More than other machines in this class. 3 Axis DRO Installed. Note: if a 3 axis DRO is added to the machine, the 3rd axis of the DRO reads the HEAD up and down, Not the quill, so it is not doubling up on the measurement. If you add the 3 axis DRO, now both Z Axis movements are covered. Drilling Capacity: 1-1/4? Max. End Milling Capacity: 1? Max. Face Milling Capacity: 3? Table Size: 27-1/2? X 7-1/8? Cross Travel (Y Axis): 8-1/2? Longitudinal Travel (X Axis): 15? Table Leadscrew Pitch 10 TPI. 100? Per Turn Table Dial Graduations. 001? Vertical Travel (Z Axis): 16? Max Distance Spindle to Table: 18-1/4? Taper of Spindle: R-8, w/7/16-20 Drawbar Thread Spindle (Quill) Travel: 3? T Slot Size: 1/2? (T Slots are slightly less than 1/2? , actual size 12mm, our 1/2? Kit is sized for this machine) Range of Spindle Speeds: 115 – 1700 rpm, 6 Steps Head Tilt: Left & Right ±90° Motor: 1 HP Net Weight (Not Including Base): 475 LBS Net Weight (With Optional Base): 575 LBS Power Required: 110/120V, 20A Circuit. 5′ cord, Includes 120V Plug with ground Dimensions (Assembled on stand): 39? W x 74? H x 30? D Height with head at top of Z travel: 80? (On Stand) Height with head at normal working height: 75? (On Stand) Optional Stand Height 32? Country of Origin: China. Machine Base Dimensions (Cast Iron Base of machine, where it sits on the chip pan) Approx. 13-1/2″Wx21″D Machine Base Dimension (Bolt Pattern) Approx. 11″Wx14-1/4″D Table Height, machine base (Where it sits on the chip tray) to table, approx. 8-1/2? Footprint of stand at floor, approx. 14-1/2? W x 21-1/4? Front to back. Average time delivered is 2-7 days depending on how far from Pittsburgh you are located. If you need liftgate service, please message us one you place your order to let us know. Quality Machine Tools / Precision Matthews Machinery Co. 1060 Montour West Industrial Park. We are machinists here too and have been in business for over 20 years. We know our machines and we know what we sell. So if there is any question, we can help.

Listing and template services provided by inkFrog.

Bridgeport model 6F power feed. I took this off my 1983 Bridgeport mill. The motor was checked by Servo Products Company and a new circuit board was installed by them in May of 2023. Unit has the following new parts : motor brushes, potentiometer, shaft seal, limit switches, on/off power switch, indicator light, and gasket for gear case cover. Runs great without any issues. It will have to be filled before using. They will be included in same box.