Good used shape, is in good working condition. Shows some normal usage wear, has some paint loss as seen. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “snydersjunkyard” and is located in this country: US. This item can be shipped to United States.

• Brand: Bridgeport
• Function: Milling
• Machine Type: Milling Machine

BRIDGEPORT THE OFF-SET TOOL CO. VERY RARE VINTAGE MORSE TAPER OFFSET MILLING TOOL. USED, but in good working condition. Need to combine orders from different listings. Some exceptions may apply. If your item is received in a different condition than stated DOA, not working properly etc… 11 LBS KL 7/6/2022 QTY 1. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “southbendindustrial” and is located in this country: US. This item can be shipped worldwide.

• Brand: BRIDGEPORT

Original Schaublin 102 150mm cross slide, good condition. This item is in the category “Business, Office & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “martes-instruments” and is located in this country: NL. This item can be shipped to North, South, or Latin America, all countries in Europe, Australia.

Rare Vintage Kearney & Trecker Astronomical Dividing Head Machinists Tool. Thank you for checking out my items. I always try and provide the best photos I can to show the condition of each item. PLEASE FEEL FREE TO MAKE AN OFFER! Notes: up for sale is a nice Rare Vintage Kearney trecker astronomical divider. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “srqantiques” and is located in this country: US. This item can be shipped to United States.

• Brand: KEARNEY & TRECKER

SPECIAL ORDER FROM BRIDGEPORT HIGH SPEED STEP HEAD 5400 RPM MAX 1-1/2 HP MOTOR RARE HEAD. COMES WITH A VISE COLLETS DRILL CHUCK HEAD WAS TUNED UP TABLE IS TIGHT 3 PHASE WE CAN DO A VFD IF YOU NEED SINGLE PHASE. WE CAN AD A POWER FEED OR A DRO , POWER DRAW BAR AT COST FOR YOU. WE CAN ALSO PAINT IT IF YOU NEED IT TO LOOK PRETTY AT COST. (DONT LET THE UGLY PAINT FOOL YOU). THIS IS A GOOD RUNNING MACHINE BEARINGS ARE GOOD. ANY MACHINES THAT NEED TO BE PALLETIZED WILL HAVE TO PAY EXTRA 200 THANK YOU. The item “BRIDGEPORT MILLING MACHINE 1 -1/2 Hp High Speed Step Pully Head CHROME WAYS RARE” is in sale since Friday, August 27, 2021. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “shawn-7334″ and is located in Cromwell, Connecticut. This item can be shipped to United States.

• Machine Type: MILLING
• Model Year: J HEAD
• X-Axis Travel Bed: AAA
• Y-Axis Travel Bed: AAA
• MPN: Does Not Apply
• Spindle Taper: 1
• Function: Milling
• Brand: BRIDGEPORT
• Table Width: 9×42
• Control: Manual
• Voltage: 220 or single phase

BRIDGEPORT’T’ HEAD – CHERRYING ATTACHMENT. EXTREMELY RARE- USED FOR MACHINING CONVEX SHAPES, KEYWAYS, DIE SINKING ETC. MT2 SPINDLE – UPTO 4250 RPM. HARDLY EVER BEEN USED- LIKE NEW. FITS TO ALL BRIDGEPORT TURRET MILLS- WOULD MAKE A GREAT ADDITION TO BRIDGEPORT ENTHUSIASTS. The item “BRIDGEPORT’T’ HEAD CHERRYING ATTACHMENT- 3 PHASE, IMMACULATE- VERY RARE” is in sale since Wednesday, May 26, 2021. This item is in the category “Business, Office & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “sorted-uk” and is located in bristol. This item can be shipped to United Kingdom, Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Australia, United States, Bahrain, Canada, Japan, New Zealand, China, Israel, Hong Kong, Norway, Indonesia, Malaysia, Mexico, Singapore, South Korea, Switzerland, Taiwan, Thailand, Bangladesh, Bermuda, Bolivia, Barbados, Brunei darussalam, Cayman islands, Egypt, Guernsey, Gibraltar, Guadeloupe, French guiana, Iceland, Jersey, Jordan, Cambodia, Liechtenstein, Sri lanka, Macao, Monaco, Maldives, Martinique, Nicaragua, Oman, Paraguay, Reunion, Saudi arabia, South africa, United arab emirates, Ukraine, Bahamas, Colombia, Jamaica, Kuwait, Panama, Philippines, Qatar, Uruguay.

• Machine Type: Turret Mill
• Power Source: Electric
• Function: Milling
• Brand: Bridgeport
• Control: Manual

CLAUSING MODEL 8530 VERTICAL MILLING MACHINE W / GEAR HOBBING ATTACHMENT. PLEASE CALL JIM FOR MORE INFO 7146121480 TNT INDUSTRIAL ORANGE CALIFORNIA. Clausing vertical and horizontal Millers were manufactured by the Johansson Company, a firm that Atlas/Clausing eventually bought out. The vertical machine was built in two models, the original 8520 and 8525 (that differed only in their quill fittings) and the later and improved 8530; the horizontal miller was designated as the 8540, 8541, 8550 and 8551, again with only relatively minor details (the type of electric motor or the provision of hand or power table feeds) to distinguish between them. A sought-after machine in its home country – and with good reason – the Clausing was a compact, strongly-built machine that could be driven by either a single or three-phase 1725 rpm 60 cycle rear-mounted motor that provided (through an all-V-belt drive system with an intermediate jockey pulley) a range of useful spindle speeds: 180, 350, 600, 1000, 1900 and 3250 rpm. To slow the spindle from higher r. A hand-operated brake was provided.. The hardened, chrome-nickel steel spindle could be ordered with either a No. 2 Morse (Model 8520) or a No. 7 Brown and Sharpe taper (Model 8525) – both perhaps a little undersize for heavier work – while the hard-chrome plated quill, with a micrometer adjustable stop, had 3 of travel by either a (useful and clever) two-speed, quick-feed lever – or a handwheel. Each quill was individually fitted at the production stage, with the housing being honed to fit. Not only could the head carrying the spindle be rotated in a vertical plane but the whole of the turret head also rotated horizontally – allowing great versatility in setting jobs and machining otherwise difficult angles. The 24″ x 6″ table, with 15″ of longitudinal and 5″ of cross movement, carried three T slots, had handles at both ends and large, clearly engraved micrometer dials. The table feed screws were of high quality, having ground threads and supported in ball bearings where they passed through the table-end brackets; options available for the table feed were an hydraulic drive for production work and (though possibly only on the later 8530 model) a hand-operated fast table feed. The latter unit consisted of a gearbox casing hung from the end of the table with a handwheel permanently attached to the lower shaft that connected directly to the reduction gearing. With the handle pushed in the feed screw was driven at a 1:1 ratio but when pulled out a “high-speed” 4 : 1 drive was engaged – where one turn of the handle rotated the feed screw through 4 turns to re-position the table very much more quickly. On the Model 8530 the option was offered of an electronically controlled power feed unit; this could be provided in two forms, to move the table just longitudinally, or in traverse as well – though unfortunately both versions earned a reputation for unreliability. For the size of miller the number and closeness of the gib-strip adjustment screws on both table and knee must be a record – but how much easier it would have been to fit a proper tapered, screw-adjusted, gib “block”. The vertical travel of the table was 11 3/8 “, the clearance between the spindle nose and table top 15 5/8 ” and the throat (from spindle centre to column) 8.5. Supplied as standard with each miller was an electrical reversing switch, collet draw bar, floor cabinet storage shelf, collet storage and chip tray. The overall dimensions were 36 ” deep x 40″ wide x 70 high. However, despite the advantages outlined, the machine was not without its problems – and there are one or two points worth keeping an eye on: the quill down-feed pinion is rather “light” for heavier work and the gears which operate the fine-down feed are also insubstantial – damage to the last gear in this train is not uncommon. On early machines the quill assembly had no return spring – and hence there was nothing to keep it from dropping if the screw that acted as a friction control was allowed to come loose (this is one miller not to use for very heavy-duty drilling with a 6-foot length of tubing slipped over the feed handle). The later and improved version of the miller carried the Model Type 8530 and had, amongst other improvements, a heavier knee with a horizontal base, a column made taller by the inclusion of a distance piece and a two-speed hand-feed to the table.. The item “RARE! CLAUSING MODEL 8530 VERTICAL MILLING MACHINE W / GEAR HOBBING ATTACHMENT” is in sale since Monday, July 5, 2021. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “tnt_industrial” and is located in Huntington Beach, California. This item can be shipped to United States.

• Machine Type: Vertical Milling Machine
• Function: Milling
• Brand: Clausing

Rockwell 21-100 Veryical Milling Machine With Rare Vises Single Phase Baldor 220 V 1 hp 3450 rpm motor. New never used 2 boring head, super rare Planken German multi angle jaw vise & large rotating vise. I got this thinking Id use it and spend many days cleaning. The aluminum motor mount housing was broke & I repaired it & it runs quiet & smooth. This is a very heavy machine, approximately 900 lbs , so you will need some sort of lift to get it. Its right by my garage door so itll be easy to move outside to load. I have No lifts, so loading is all you. Located in Masonville/ Sidney Center, NY. The previous owner said his dad made one shaft back in early 1970s & was the only time he personally used it. Look at all photos and ask any questions, all sales are final. Very hard to find. The item “Rockwell 21-100 Vertical Milling Machine With Rare Vises Single Phase” is in sale since Saturday, June 19, 2021. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “skinglenn” and is located in Masonville, New York. This item can’t be shipped, the buyer must pick up the item.

• Machine Type: Milling Machine
• Model: Rockwell 21 – 100

Hardinge BB2V Vertical Milling Machine + Rare Collets + Very Rare Vise. Hate to have to part with this beefy little Hardinge mill but it’s been a tough year. She’s in good shape and comes with the following. New polyurethane spindle belt. A set of (very rare) Hardinge 2VB collets (sizes 1/16″, 1/8″, 3/16″, 1/4″, 5/16″, 3/8″, 7/16″, 1/2″). An original low-profile Hardinge swivel vise (not pictured). All parts needed to convert to lever feed on the X-axis (designed and made by me). The previous owner swapped the original motor over to a 120V motor. I had planned to put in a VFD and link it to the levers eventually, but never got around to it. Works fine as is, but adding a VFD would give you easier speed changes. The table working surface is 12″ x 3 3/16″. The travel of the table is 5″ (longitudinal) x 3 1/8″ (transverse) x 5 (vertical). The machine footprint is: 39″ x 38″ (allows cabinet door to open) x 60 tall. The item “Hardinge BB2V Vertical Milling Machine + Rare Collets + Very Rare Vise” is in sale since Thursday, December 10, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “hessehessehesse” and is located in Kalamazoo, Michigan. This item can’t be shipped, the buyer must pick up the item.

• Brand: Hardinge
• Machine Type: Vertical Milling Machine
• Model Year: Unknown
• Function: Milling
• Power Source: Electric
• Spindle Horsepower: 1 hp
• Control: Manual

Even Though The Machine Looks Good It Is Used So We Prefer And/Or Strongly Recommend You Visit & Inspect It Yourself In Person ;However, Should This Not Be Possible Or Practical Please Review The Photos & Ask As Many Questions As Possible So You Know What To Expect When It Arrives!! This Has Been , Inspected And Tested For It’s Function Only… We Can Not & Do Not Determine If It Meets Any And/Or All Safety Issues And/Or Concerns With Regards To The Machine, It’s Installation , Operation & Safe Guarding. Any And/Or All Issues Or Concerns With Regards Safety Are The Buyers Sole Responsibility And By Purchasing This Machine You Are Agreeing And Accepting The Terms Above. Machine Details & Specifications. Brown & Sharpe Light No 2 Universal Milling Machine W/Loads & Loads Of Mostly New Tooling Including Dividing Head W/ Tail Stock And More! What You See Is What You Get!! Safety Requirements & Standards. Brenda & Cliff Davis. Bdavis AT davismachinery DOT c o m. The item “Brown & Sharpe Light No 2 Universal Milling Machine WithLoads Tooling. Rare Find” is in sale since Sunday, October 18, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “davismachinery” and is located in Providence, Rhode Island. This item can be shipped to United States.

• Country/Region of Manufacture: United States
• Model Year: Antique
• Type: Horizontal Milling Machine
• Make: Van Norman