Very nice knee mill, Enco base with eagle (like Seiki XL) head converted from mechanical varidrive to fixed pulley belt with variable frequency drive and baldor 3hp inverter duty motor. Erickson quick change qc 30 taper spindle with wrench and one tool holder. No messing with a drawbar wrench, this is 1/4 turn quick release right at the spindle and your cutter is always the same length, no fooling with adjusting cutter up and down in an r-8 collet. One shot oiler, power feed on x axis, power vent fan on motor, vise included. This unit runs on regular single phase 230v power and you can vary the speed right at the inverter drive mounted on the head. Good ways, good candidate for a cnc conversion- the ac drive can be controlled by your cnc controller should you eventually go that route. In zip code 30527. Contact for clarification if this is unclear. Look at ALL of the photos. If you do not respond after the 3. Jelly on the right side of the listing page, then “contact member” link on the left side of the next page. “COMMERCIAL ADDRESS” MEANS A LICENSED BUSINESS WITH A SIGN OUT FRONT AND DOCK OR LIFT. This could be hundreds of dollars difference. For our location google Clermont GA 30527 or industrialtoolandmachineworks (one word). If damaged in transit you will need to file the claim. CONDITION: Every attempt is made at accurate description. ASK for full res photos, video of operational testing, etc. Photos may have distortion, are for general scale only. Do not rely on photos even with rulers for critical dimensional data or quantity. Opinion of condition is only that, an opinion. SOME ITEMS MAY HAVE DUST, DIRT, PAINT, ENGRAVING OR GREASE, CORDS MAY HAVE REPAIRS. HARDWARE NOT SHOWN IS NOT INCLUDED. Ask for better pics if you care. All items subject to local sale while listed. DO NOT JUST ASK FOR UPS RED. THERE ARE 6 DIFFERENT SPEEDS OF UPS: Ground, 2. Day air end of day for about 2x ground price, next day air saver for about 2x 2. Day air price, next day air 10:30am (add about 10%), and next day air 8am for about 2x the 10:30am price. If that data is incorrect you may never get your package, so make sure your info is current. We have absolutely no control over time in transit with any carrier. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “tom.jelly” and is located in this country: US. This item can be shipped to United States.

• Spindle Horsepower: 3 hp
• Machine Type: Vertical Milling Machine
• Power Source: Electric
• Custom Bundle: No
• Spindle Taper: QC 30
• Modified Item: No
• Brand: Unbranded
• Function: Drilling, Milling
• Control: Automatic, Manual, Semi-Automatic
• Max Spindle Speed (RPM): 4200
• Voltage: 240 V

American Business ALL ITEMS IN STOCK IN CALIFORNIA. American STANDARD PRODUCTS QUALITY GUARANTEED. AS-250 150Lbs Torque Power Feed Milling Machine X-Axis ALSGS 0-200RPM. WHY SHOP WITH BLTPRESS? Item was as described and arrived quickly. AS-250-150 X-Axis Power Feed Kit. 0-200 RPM Rotate Speed & 150 in-lb Torque & 110 V, 60 Hz. The machine is used for X axis, if you want to used for Y axis, a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Speed can be adjust according to operator’s requirement, ranging from 0-9. Normally, jog switch should be at “FEED” position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. X-axis Power FeedPower Feed X-Axis, Voltage: 110V, 60Hz, Rotate Speed: 200 RPM, Max Torque: 150 in-lb, Dimension: 33 x 20 x 18cm / 12.99” x 7.87” x 7.09”. Easy SetupFit almost any vertical knee type milling machine with the 5/8 shaft end. Small volume and easy installation, noiseless direction changes. Durable & Long LastingSecure design helps to keep transmission gear and electronic components; two gears of this power table feed will not mesh and wear at the same spot, maximizing durability and longevity. Ergonomic DesignPower feed is equipped with security feature to keep transmission gear and electronic components as to meet the requirements of ergonomics. Quiet & Rapid OperationWith speed adjust knob, speed can be adjusted according to operator’s requirement, ranging from 0-9. Jog switch should be at “FEED” position. Fit almost any vertical knee type milling machine with the 5/8 shaft end. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Make sure the power feed stops before you change the direction. The switch should be in the “OFF” position when the machine is not in use or before plugging. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). X-axis power feed for Bridgeport type milling machines. Reversible and auto shut-off at end of cut. Limit switch for sensitive stop. No loss of dial or hand crank. Small volume and easy installation. Excellent speed control in the entire range. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Voltage : 110 V, 60 Hz. Rotate speed : 0-200 rpm. Length : 33 cm (13 inch). Width : 20 cm (7.9 inch). Height : 18 cm (7 inch). Gross weight : 6.5 kg(14.3 lb). AS-250-150 X-Axis Power Feed for Milling Machine x 1. Set of Necessary Accessories x 1. English Manual x 1. All items are dispatched from our warehouse in HACIENDA HEIGHTS, CA. Some products may be dispatched in more than one carton. International Buyers – Please Note. If you have a problem with the product. We will require a picture of the damaged part for verification. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “best_factory” and is located in this country: US. This item can be shipped to United States.

• Rotate speed: 0-200 RPM
• Torque: 150 lbs
• Package size: 13\
• Gross weight: 6.5 kg(14.3 lb)
• Warranty: Lifetime
• UPC: 0895800908294
• EAN: 0895800908294
• Brand: VEVOR
• Function: Milling
• Control: Manual
• Machine Type: Milling Machine
• Power Source: Electric
• Max Spindle Speed (RPM): 200 rpm
• Voltage: 110 V
• Model: AS-250
• MPN: XUNBS00840

This FlashCut CNC 4-Axis Milling Machine looks to be in decent cosmetic condition, showing some signs of wear. Among other things, the system feature a FlashCut FCS-3182P-01 CNC Servo Controller, a FlashCut 501A Signal Generator, a Systro Isel FC 1200-D Spindle Motor Controllers, and a Menzel Metallchemie Valve Assembly. I do not have the key for the base unit, and I was unable to test it to power up, but the other controllers powered up, as shown. The buttons on the front of the main housing unit are somewhat damaged, as shown. I had to unscrew the cover in order to open the enclosure. Approximate overall unpacked dimenions: 48″L x 40″W x 38H. No software, power cords, or other accessories are included unless stated above. The unpacked weight of this item is 428 pounds. Is there a Dock or Forklift available? The sale of this item may be subject to regulation by the U. Food and Drug Administration and state and local regulatory agencies. Outback Equipment Company Gilroy, California. Listing and template services provided by inkFrog. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Machining Centers & Milling Machines”. The seller is “outback6″ and is located in this country: US. This item can be shipped to United States.

• Machine Type: Milling Machine
• Brand: FlashCut CNC