A Class APF-750Z, Z Axis Power feed. 100% Made in Taiwan. Can fit Acer, Bridgeport, and most Taiwanese import mills. Add an auto power table feed to your milling machine for a simple and inexpensive way to increase user productivity on any conventional milling machine. “Aclass” powerfeeds feature next-generation design that boasts a number of improvements. Clutch device, direction changes are noiseless and effortless to operate. If tool crashes into workpiece or if there’s abrupt change in direction, the powerfeed has. Safety feature to protect the transmission gear and electronic components. Rapid traverse button is built right on top of the direction switch. The ergonomic design reduces fatique and stress. Jog function can be operated at any feed speed, so workpeice can be moved into position easily. On the table limit switchs are coolant proof, oil proof and protected from dust. Zero point repositionings repeatable within 0.05mm (0.00019) at the same speed. The powerfeed uses spiral bevel gear to transfer power to leadscrew for low noise operation and long operating life. Excellent speed control across the entire range. When cutting, speed variation is very low for better surface finishes. On the other hand, at low speed traverse, the power table feed won’t vibrate or strain. The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. 107T for plastic transmission gear and 6T for motor shaft gear 107 is not divisible by 6, 107 % 6 = 17.8333333333… The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Maximum Torque Using new patent Electron-Magnetic Clutch Devise for quiet operation and easy maintenance. Rapid Feed switch designed with the Direction Control Knob for easy and rapid operation. JOG Function working with any speed for operator easily find the machined point of working piece. X or Y axis. 110V / 2.8amp. X, Y or Z axis. 110V / 3.0amp. 110V / 3.4amp. Fullerton Office 2320 E Valencia Dr Fullerton, CA 92831. Piscataway Office 244 N. Randolphville Road Piscataway, NJ 08854. 2320 E Valencia Dr Fullerton, CA 92831. Note: Weight restrictions may apply in some cases. Orders under 150 lbs. Orders above 150 lbs. We guarantee the items are exactly as said in description. Thank you for viewing. Supra Machine Tool appreciates your business very much. Supra Machine Tool E-bay Store. For a wide selection of parts for milling machine, machining center, surface grinder, and engine lathes. The free listing tool. The item “Milling Machine Part- Z Axis Power feed fits Bridgeport- A Class APF-750Z” is in sale since Wednesday, January 20, 2016. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “supramachinetool” and is located in Fullerton, California. This item can be shipped worldwide.

• Brand: A Class
• Country/Region of Manufacture: Taiwan
• MPN: APF-750Z

Milling Machine Accessory – Right Angle Attachment R8 fits Bridgeport. Milling Machine Right Angle Attachment. Fits Bridgeport-style milling machines with a 3 3/8 (8586mm) quill diameter and R8 spindle taper Converts a vertical mill into a horizontal mill. Note: Maximum allowed speed with right angle attachment is 2000 rpm. Spindle runout is ± 20 micron (0.00078″) WHAT YOU’LL RECEIVE Right angle attachment, R8 stub arbor, Drawbar extension socket, 7/16-20 bolt with 1/2″ hex head Wooden box. If You have any questions regarding this item, please let us know we’ll be happy to help. The item “Milling Machine Accessory Right Angle Attachment R8 fits Bridgeport” is in sale since Saturday, March 23, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “eisenmachineryinc” and is located in Ontario, California. This item can be shipped worldwide.

• Brand: GemPower
• Model: G102-R8
• MPN: G102-R8
• Country/Region of Manufacture: Taiwan

Milling Machine Accessory – Right Angle Attachment R8 fits Bridgeport. Milling Machine Right Angle Attachment. Fits Bridgeport-style milling machines with a 3 3/8 (8586mm) quill diameter and R8 spindle taper. Converts a vertical mill into a horizontal mill. Note: Maximum allowed speed with right angle attachment is 2000 rpm. Spindle runout is ± 20 micron (0.00078). WHAT YOU’LL RECEIVE. 7/16-20 bolt with 1/2 hex head. The item “Milling Machine Accessory Right Angle Attachment R8 fits Bridgeport” is in sale since Sunday, March 3, 2019. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “jojo9000c” and is located in Mira Loma, California. This item can be shipped to United States.

• Brand: GemPower
• Model: G102-R8
• Country/Region of Manufacture: Taiwan
• MPN: G102-R8

Milling Machine Accessory – Right Angle Attachment R8 fits Bridgeport. Milling Machine Right Angle Attachment. Fits Bridgeport-style milling machines with a 3 3/8 (8586mm) quill diameter and R8 spindle taper Converts a vertical mill into a horizontal mill. Note: Maximum allowed speed with right angle attachment is 2000 rpm. Spindle runout is ± 20 micron (0.00078″) WHAT YOU’LL RECEIVE Right angle attachment, R8 stub arbor, Drawbar extension socket, 7/16-20 bolt with 1/2″ hex head Wooden box. If You have any questions regarding this item, please let us know we’ll be happy to help. The item “Milling Machine Accessory Right Angle Attachment R8 fits Bridgeport” is in sale since Monday, December 31, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “eisenmachineryinc” and is located in Ontario, California. This item can be shipped worldwide.

• Brand: GemPower
• Model: G102-R8
• MPN: G102-R8
• Country/Region of Manufacture: Taiwan

X Axis (Left/Right Table Travel) Power Feed Kit for Precision Matthews, Bridgeport, and Similar Knee Type Milling Machines. SHIPS SAME DAY IF ORDERED BY 2PM EASTERN STANDARD TIME! These will fit almost any vertical knee type mill out there, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First, and many, many more. As long as it is the Bridgeport Type Machine, it should fit. These use 110V, Single Phase Power, just a standard 110/120V outlet is needed. This set includes everything you should need to install this power feed, including the power feed unit, mounting bracket, drive gear, shims, safety stop with track, and hardware. If you have any questions about this unit at all, please feel free to ask. Our Part # PF-X-AL310SX. The item “X AXIS POWER FEED KNEE MILLS FITS BRIDGEPORT & OTHER MILLING MACHINE FREE SHIP” is in sale since Saturday, August 4, 2018. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “qualitymachinetools” and is located in Pittsburgh, Pennsylvania. This item can be shipped to United States.

• Model: PF-X-AL310SX
• Modified Item: No
• Custom Bundle: No
• MPN: PF-X-AL310SX
• Brand: PRECISION MATTHEWS
• Non-Domestic Product: No

Sign up to Newsletters. Power Feed APF-500X Torque for Type Milling Machines 0-210 RPM Feeding Device. You are looking at our new Power Feed X for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. 107T for plastic transmission gear and 6T for motor shaft gear 107 is not divisible by 6, 107 % 6 = 17.8333333333… The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Set the fix stand on work table, set table bearing bushing on the axis screw, then set the power table feed on the fix stand, take out the gear housing. Use one hand to hold the center transmission shaft. Set the bevel gear on axis screw with the other hand. Then check if the backlash between gears is between 0.1-0.2mm. Add shims (1.0t, 0.25t, 0.1t) if the backlash is too large. Repeat step 2-3 until reaching satisfying backlash. Tighten the handle to start setting socket parallel key and bevel gear. Rotate the handle slightly to feel if any interfere occurs in between. If do, please repeat step 3-4 to add more shims. If not, go to next step. Take out the handle, add proper shim (43×33), adjust the backlash between dial & bevel gear and lock with fix ring. Set the handle and tighten, slightly rotate the handle. Normally it should be smooth without any interfere. Finally, set the gear housing and limit switch. Power supply switch and reset switch. The right side of power switch is ON. The left side is OFF. Red light will show when machine is on. The red round button on right side is reset switch. Reset button will jump up to cut off the power if the machine overloads. The operator must reduce cutting load, then press reset switch to continue operating. Feed knob and rapid button. Rotate feed knob after power is on. Turn left for left side feeding and vice versa. The button in the middle is rapid button. Tool will travel rapidly to left side if you keep pressing the button. Release to make power table feed will back to normal speed. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. NOTE: To stop jog operating, you must first turn FEED KNOB TO 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Add an auto power table feed to your milling machine. A simple and inexpensive way to increase productivity. Small volume and easy installation. Excellent speed control in the entire range. Jog function operates at any feed speed. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Package Dimensions: 11713(275175335mm). 1 x X-Axis Fix Stand with Bushing. 1 x Bevel Gear with Fix Ring. 1 x Handle Washer. 2 x Stop Blocks. 2 x Stop Set. 2 x Socket Screws (M8P1.2535). X Socket Screws M8P1.0. 6 x Small Shims. 2 x Small Shims 26.2. 3 x Small Shims 26.2. 4 x Large Shims. 2 x Spring Pins. 1 x Cable Clamp. 1 x User Manual. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “Milling machine accessory ACLASS X-Axis Power Feed APF-500X fits Bridgepor” is in sale since Monday, May 22, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “wholesale2worldwide” and is located in Ontario, California. This item can be shipped to United States, all countries in Europe, Canada, Mexico, Australia.

• Brand: VEVOR
• MPN: UGFSA006
• Model: APF-500X
• Country/Region of Manufacture: CHINA
• Torque: 135lbs
• Weight: 13.2lbs
• Color: White
• Current: 2.8A
• R.P.M.: 0-210
• Package Dimension: 11 x 7 x 13 inch

Sign up to Newsletters. Power Feed APF-500X Torque for Type Milling Machines 0-210 RPM Feeding Device. You are looking at our new Power Feed X for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. 107T for plastic transmission gear and 6T for motor shaft gear 107 is not divisible by 6, 107 % 6 = 17.8333333333… The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Set the fix stand on work table, set table bearing bushing on the axis screw, then set the power table feed on the fix stand, take out the gear housing. Use one hand to hold the center transmission shaft. Set the bevel gear on axis screw with the other hand. Then check if the backlash between gears is between 0.1-0.2mm. Add shims (1.0t, 0.25t, 0.1t) if the backlash is too large. Repeat step 2-3 until reaching satisfying backlash. Tighten the handle to start setting socket parallel key and bevel gear. Rotate the handle slightly to feel if any interfere occurs in between. If do, please repeat step 3-4 to add more shims. If not, go to next step. Take out the handle, add proper shim (43×33), adjust the backlash between dial & bevel gear and lock with fix ring. Set the handle and tighten, slightly rotate the handle. Normally it should be smooth without any interfere. Finally, set the gear housing and limit switch. Power supply switch and reset switch. The right side of power switch is ON. The left side is OFF. Red light will show when machine is on. The red round button on right side is reset switch. Reset button will jump up to cut off the power if the machine overloads. The operator must reduce cutting load, then press reset switch to continue operating. Feed knob and rapid button. Rotate feed knob after power is on. Turn left for left side feeding and vice versa. The button in the middle is rapid button. Tool will travel rapidly to left side if you keep pressing the button. Release to make power table feed will back to normal speed. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. NOTE: To stop jog operating, you must first turn FEED KNOB TO 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Add an auto power table feed to your milling machine. A simple and inexpensive way to increase productivity. Small volume and easy installation. Excellent speed control in the entire range. Jog function operates at any feed speed. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Package Dimensions: 11713(275175335mm). 1 x X-Axis Fix Stand with Bushing. 1 x Bevel Gear with Fix Ring. 1 x Handle Washer. 2 x Stop Blocks. 2 x Stop Set. 2 x Socket Screws (M8P1.2535). X Socket Screws M8P1.0. 6 x Small Shims. 2 x Small Shims 26.2. 3 x Small Shims 26.2. 4 x Large Shims. 2 x Spring Pins. 1 x Cable Clamp. 1 x User Manual. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “X Axis Power Feed Milling Mill Fits Table Milling Machine Bridgeport Acer” is in sale since Sunday, July 23, 2017. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Equipment Specific Tooling\Milling”. The seller is “rumei-shopping” and is located in Ontario, California. This item can be shipped to United States, all countries in Europe, Canada, Mexico, Australia.

• Brand: VEVOR
• MPN: KJLXC009
• Model: APF-500X
• Country/Region of Manufacture: CHINA
• Torque: 135lbs
• Weight: 13.2lbs
• Color: White
• Current: 2.8A
• R.P.M.: 0-210
• Package Dimension: 11 x 7 x 13 inch

Milling Machine Accessory – Right Angle Attachment R8 fits Bridgeport. Milling Machine Right Angle Attachment. Fits Bridgeport-style milling machines with a 3 3/8 (8586mm) quill diameter and R8 spindle taper Converts a vertical mill into a horizontal mill. Note: Maximum allowed speed with right angle attachment is 2000 rpm. Spindle runout is ± 20 micron (0.00078″) WHAT YOU’LL RECEIVE Right angle attachment, R8 stub arbor, Drawbar extension socket, 7/16-20 bolt with 1/2″ hex head Wooden box. If You have any questions regarding this item, please let us know we’ll be happy to help. The item “Milling Machine Accessory Right Angle Attachment R8 fits Bridgeport” is in sale since Thursday, June 21, 2018. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “eisenmachineryinc” and is located in Ontario, California. This item can be shipped worldwide.

• Brand: GemPower
• MPN: G102-R8
• Country/Region of Manufacture: Taiwan
• Model: G102-R8

Maxi Torque Rite Power Draw Bar – Authorized Distributor – Proudly Made in the USA. Maxi torque rite drawbar Tech Data and Quantity Specials. SEE OTHER MAXI TORQUE MODELS FOR SALE SPECIFY MODEL & SPINDLE TYPE. TR 100 DB164 For Jet Model JTM4VS + Atlas 2VS08,3VS08 Machines. Acer Manual Machines CAT 40 SpindleTR 100 DB286. Kent Models KTM3VKF & KTM4VKF Machines (R8). TR 100 DB289 For Kent Model KTM5VKF Machines (NMTB 40). TR 100 DB325 For Jet Model JTM1050 Machines (R8). TR 100 DB343 For Summit VS350 (R8) Machines. TR 100 DB 273 For All 3V Style Acer Mils. Maxi Torque Rite Air Power Draw Bar For Manual & CNC Milling Machines. TR100-DB100 Automatic Drawbar complete system (shown above). Maxi Torque Rite Air Power Draw Bar is a Air Powered Drawbar Pneumatically Operated. TR100-DB100 Automatic Drawbar complete system. Fits BRIDGEPORT Manual Mills/Milling Machines WITH R-8 SPINDLE. SELECT 2 & 3 Axis BRIDGEPORT CNC Milling Mills. Saves Labor Time in Tool Changeovers. Improves work Holding Accuracy and Repeatability. Ergonomically Designed for Ease of Operator Repetitive Usage! Factory Trained Full Support and Service with Local Stocked Parts Availability and Interchangeability. COMPARE OUR 100% USA MADE with Our Superior Quality, performance, manufacturing features and LOW COST. Maxi Torque Rite Air Power Draw Bar. The item “Maxi Torque Air Power Drawbar TR100DB100 FITS Bridgeport Manual Mill R8 Spindle” is in sale since Tuesday, August 8, 2017. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “machinery4less” and is located in Greeneville, Tennessee. This item can be shipped to United States, Canada.

• Model: TR100-DB100
• Country/Region of Manufacture: United States
• MPN: TR100-DB100
• Brand: MAXI TORQUE Airpower Drawbar

Sign up to Newsletters. Power Feed APF-500X Torque for Type Milling Machines 0-210 RPM Feeding Device. You are looking at our new Power Feed X for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8 Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First… The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. 107T for plastic transmission gear and 6T for motor shaft gear 107 is not divisible by 6, 107 % 6 = 17.8333333333… The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Set the fix stand on work table, set table bearing bushing on the axis screw, then set the power table feed on the fix stand, take out the gear housing. Use one hand to hold the center transmission shaft. Set the bevel gear on axis screw with the other hand. Then check if the backlash between gears is between 0.1-0.2mm. Add shims (1.0t, 0.25t, 0.1t) if the backlash is too large. Repeat step 2-3 until reaching satisfying backlash. Tighten the handle to start setting socket parallel key and bevel gear. Rotate the handle slightly to feel if any interfere occurs in between. If do, please repeat step 3-4 to add more shims. If not, go to next step. Take out the handle, add proper shim (43×33), adjust the backlash between dial & bevel gear and lock with fix ring. Set the handle and tighten, slightly rotate the handle. Normally it should be smooth without any interfere. Finally, set the gear housing and limit switch. Power supply switch and reset switch. The right side of power switch is ON. The left side is OFF. Red light will show when machine is on. The red round button on right side is reset switch. Reset button will jump up to cut off the power if the machine overloads. The operator must reduce cutting load, then press reset switch to continue operating. Feed knob and rapid button. Rotate feed knob after power is on. Turn left for left side feeding and vice versa. The button in the middle is rapid button. Tool will travel rapidly to left side if you keep pressing the button. Release to make power table feed will back to normal speed. Speed can be adjust according to operators requirement, ranging from 0-9. Normally, jog switch should be at FEED position. For jog movement, just switch to “0″ position. Kept holding the switch until it travels to requires position. NOTE: To stop jog operating, you must first turn FEED KNOB TO 0(OFF) position. Then move JOG SWITCH to FEED position. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). Add an auto power table feed to your milling machine. A simple and inexpensive way to increase productivity. Small volume and easy installation. Excellent speed control in the entire range. Jog function operates at any feed speed. Power table feed won’t vibrate or strain in low speed. Direction control knob for easy and rapid operation. Safety feature to protect transmission gear and electronic components. Package Dimensions: 11713(275175335mm). 1 x X-Axis Fix Stand with Bushing. 1 x Bevel Gear with Fix Ring. 1 x Handle Washer. 2 x Stop Blocks. 2 x Stop Set. 2 x Socket Screws (M8P1.2535). X Socket Screws M8P1.0. 6 x Small Shims. 2 x Small Shims 26.2. 3 x Small Shims 26.2. 4 x Large Shims. 2 x Spring Pins. 1 x Cable Clamp. 1 x User Manual. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “X AXIS POWER FEED MILLING BRIDGEPORT ACER MILLING MACHINE MILL FITS” is in sale since Thursday, April 13, 2017. This item is in the category “Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Equipment Specific Tooling\Milling”. The seller is “happykisssoul” and is located in Ontario, California. This item can be shipped to United States, all countries in Europe, Canada, Mexico, Australia.

• Brand: VEVOR N
• MPN: GFGFD006
• Model: APF-500X
• Country/Region of Manufacture: CHINA
• Torque: 135lbs
• Weight: 13.2lbs
• Color: White
• Current: 2.8A
• R.P.M.: 0-210
• Package Dimension: 11 x 7 x 13 inch