Table Size: 9.0″ x 42.0″. X-Axis Travel: 26.0. Y-Axis Travel: 12.0. Knee Travel: 16.0. Quill Travel: 5.0. Spindle Horsepower: 1 HP. Spindle Rpm: (8) 80 – 2720 RPM. Machine Weight: 2,200 lbs. Voltage: 220v – 3 Phase.

This listing is for an “on-site” or “at your shop” Bridgeport milling machine service. Pricing is for Midwest region. We can go to any region however the price increases a bit. The things that can cause the price to fluctuate a bit is how far out you are from St. Louis Missouri, where we are located. Also, the condition of your machine, sometimes allows for options on site that cause the price to be a little higher. Typically though it’s your choice to replace these things while we are doing the service. This basic service includes a complete upper housing rebuild, the lower spindle housing gets tuned up and spindle bearings replaced, the transmission housing gets cleaned out and repacked with grease. Things that are an added cost in the head are the splined and spindle gear hubs And the bull gears. Also if your motor shaft is all banged up, sometimes a new motor is necessary, which would be an extra cost. The base of the machine gets completely disassembled, cleaned out and reassembled with new wipers, new leads, screw, bearings, and new nuts. The oil system gets checked and limiters get replaced if they’re clogged also a new reservoir on your oiler is included because they get brittle and have a tendency to crack overtime. Things that would be an additional charge are lead screws, the oiler pump itself, Power feed and read out. Obviously, there are quite a few things they could addressed as we proceeded through the machine that are not listed in the description. Get in touch via the messaging option for further details.

Type 150 Power Feed. Type 150 – Y Axis Cross Feed. Semi-automated machining on Class 1 mills to 3 hp. Peak Torque (full-wave SCR control compound DC motor): to 150 in. / 17 NM torque. Intermittent Torque: 120 in. / 13.6 NM. Continuous Torque: 100 in. / 11.3 NM. 50-35 IPM / 13-889 mm/min. Rapid Traverse: 35 IPM / 889 mm/min. Gear Reduction Ratio (motor to screw shaft): 72:1. Smooth surface finish at speeds as low as 0.5 ipm or 13 mm/min. Superior speed regulation, ramping, dynamic breaking, friction safety clutch and limiting circuit protection. Helical gearing and torque limiting friction saftey clutch with new and improved gear. Electrical: 110V, 50/60 Hz, 3 Amps. / 6.8 kg.

Bridgeport 6F power feed controller with Seco Electronics Corp. D28595 (117VAC, 60Hz, 10A) and Boehm 4640 crossfeed motor milling machine assembly. From a closing industrial facility. Untested but presumed to be working well. The following information is provided by an AI description service. The Bridgeport 6F Power Feed Controller Seco D28595 Boehm 4640 Crossfeed Motor Assy is a specialized component designed for milling machines. This product is known for its quality and durability, making it a reliable choice for metalworking equipment in various industries. With the Bridgeport brand reputation and compatibility with milling machines, this power feed controller ensures precise and efficient control of the machine’s movements, enhancing overall performance and productivity in cutting and drilling tasks.

Pulled this off my mill, works fine, comes with forward reverse switch and cord. 1hp, 3 phase, 3/4 shaft. Not sure all of what machines it will fit, but it was on my Bridgeport J-head.

BRIDGEPORT R8 RIGHT ANGLE HEAD MILLING ATTACHMENT.

Bridgeport milling machine used.

X-Axis Power Feed 450 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM. About of the item. X-Axis power feed is made of aluminuml;Power Parameter:90Watt, 110V input voltage, 50/60Hz, single phase;Rotate Speed:0-200 RPM. Max Torque:450in-lb;Max feed rate: 650mm/min; Max return speed: 850mm/min. This power feed fits some milling machines like Bridgeport, Precision Matthews, Enco, Jet, Sharp, Acer, Webb, etc. AUTOMATIC AND MANUAL CONTROL? You have the option to operate this power feed in automatic mode at a constant speed, allowing you to work hands-free. Alternatively, you can manually adjust the speed control knob for more precise milling work. This versatile power feed provides excellent speed control throughout the entire range to meet your specific needs. Equipped with the Gleason Spiral Bevel Gear, this power feed ensures stable transmission ratio, minimal transmission noise, high efficiency, and superior bearing capacity. Additionally, it features a special safety device that protects the transmission plastic gear and electronic parts from damage in case of tool collision or instantaneous reversal during fast transmission. PORTABLE AND EASY TO INSTALL? Compact and portable, this milling machine power feed weighs only 3.75kg/8.27lbs and measures 73.512.8 inches in size. Whether you are a novice or a skilled operator, installing this power feed is a breeze. Just follow the instructions and online video or install it on your own. Designed to fit milling machines such as Bridgeport, Precision Matthews, Enco, Jet, Sharp, Acer, Webb, and more, this power feed is versatile. It specifically fits vertical knee-type mills with the same mounting pattern and a 5/8 diameter shaft on the end. However, please note that it will not fit mills with a different mounting pattern or different sized leadscrews, such as Powermatic and some other irregularly sized machines. Therefore, please ensure that your machine follows the typical Bridgeport type mentioned above. We accept Payoneer only. The parcel maybe delay 1-2day of the weekend. Due to the bad weather, Holidays, Hot Season ect. The parcel maybe delay, If you have any problems, mssage us, we will try our best to solve it. We cannot deliver your order if your state is PR. Message us for return instructions. If you are not satisfied with the item for any reason, please do not quick to leave negative/neutral feedback even open request and case without any communication with us. We devote ourselves making EVERY CUSTOMER in 100% Satisfactory and resolve any problem.

VINTAGE MACHINEST TOOL BRIDGEPORT? 6 MILLING WORKHOLDING MACHINE VICE. Recent Barn Find Please See Pictures As They Are.

Complete head 220 we can do a vfd if u need single phase.